How to Service and Repair the Rear Three-Piece Drive Shaft on 2008 Ford F-350 Super Duty?

A hoist should support the vehicle in neutral gear when servicing the rear three-piece driveshaft. Index-mark the driveshaft flanges and slip joints. A plastic or rubber soft-faced hammer should be used to tap on the yoke or bearing cup assembly in order to unseat the bearing cup assembly. You must disconnect the driveshaft from the axle flange by removing and discarding the 4 bolts and the 2 U-joint retainers before supporting the driveshaft with mechanic's wire. The next step requires draining the driveshaft coupling shaft by separating 4 bolts along with 2 U-joint retainers for disposal in addition to driveshaft maintenance support. The rear coupling shaft assembly together with the 2 bearing support bolts must be taken out. Drive the driveshaft yoke removal process by using a plastic or rubber soft-faced hammer on the yoke surface when no pry area is present. You should remove both center bearing support bolts and discard the 4 flange bolts in order to extract the front driveshaft. Wash away grease deposits together with dirt and rust from both driveshaft yoke regions and all driveshaft elements while leaving the driveshaft center bearing bearing and rubber insulator exposed to solvent-free cleaning only. The inspection of the universal joint slip yoke boot should include testing for holes or tears with a replacement boot if necessary and examination of the driveshaft center bearing support for wear or rough action which requires a new support. The front driveshaft installation requires index mark alignment before attaching it to the transmission while using 4 new bolts with hand-only tightening. First install the center support bearing before adding the two bolts while hand-tightening them. The installation requires torquing the 4 driveshaft-to-transmission flange bolts to 100 Nm (74 ft. lbs.) as well as the 2 driveshaft center bearing bolts to 70 Nm (52 ft. lbs.). Position the rear coupling shaft assembly before installing 2 center support bearing bolts that should be tightened with hand pressure. Install the rear coupling shaft assembly to the front driveshaft by using 2 new retainers and 4 driveshaft-to-coupling shaft bolts that require a torque setting of 70 Nm (52 ft. lbs.). When fitting the flange onto the rear axle pinion flange pilot ensure a tight fit before equally tightening all bolts according to a cross pattern. The rear coupling shaft assembly installation ends with attaching it to the rear axle while applying 70 Nm torque to 4 new bolts and 70 Nm torque to 2 center support bearing bolts.

OEM 2008 Ford F-350 Super Duty Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

67 Drive Shafts found

View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4R602-EG
$680.03 MSRP: $940.75
You Save: $260.72 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 63.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-EG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Lariat, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4R602-HH
$403.37 MSRP: $558.03
You Save: $154.66 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 68.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-HH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Axle Shaft, Front Driver Side Part Number: EC3Z-3220-E
$445.71 MSRP: $654.50
You Save: $208.79 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Assembly
- Position: Front Driver Side
- Replaces: AC3Z-3220-B, EC3Z-3220-C, BC3Z-3220-C
- Item Weight: 28.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: EC3Z-3220-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, Platinum, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.4 L DIESEL, 8 Cyl 6.7 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4R602-AX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 64.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-AX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4602-AH
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 43.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-AH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4R602-GH
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-GH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4R602-HA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 57.90 Pounds
- Item Dimensions: 75.8 x 11.1 x 8.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-HA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: AC3Z-4R602-A
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 7C3Z-4R602-FC, 7C3Z-4R602-BZ
- Base No.: 4R602
- Item Weight: 59.70 Pounds
- Item Dimensions: 25.7 x 6.0 x 15.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: AC3Z-4R602-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 4C3Z-4602-DA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 42.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-4602-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 6C3Z-4602-A
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 27.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6C3Z-4602-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4602-AD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 64.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-AD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4602-AJ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 46.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-AJ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4602-AQ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 26.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-AQ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4602-AV
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 24.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-AV
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4602-BF
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 14.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-BF
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4602-BG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 43.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-BG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4602-BL
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4602-AK
- Base No.: 4602
- Item Weight: 35.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-BL
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL, 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4602-BP
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 7C3Z-4602-AR
- Item Weight: 23.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-BP
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4R602-AZ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 58.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-AZ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- XL | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford F-350 Super Duty Drive Shaft Part Number: 7C3Z-4R602-BB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 63.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS

| Page 1 of 4 |Next >

1-20 of 67 Results

2008 Ford F-350 Super Duty Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2008 Ford F-350 Super Duty Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2008 Ford F-350 Super Duty Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2008 Ford F-350 Super Duty Drive Shaft Parts Q&A

Q: How to Service and Repair the Rear Three-Piece Drive Shaft on 2008 Ford F-350 Super Duty?
A: A hoist should support the vehicle in neutral gear when servicing the rear three-piece driveshaft. Index-mark the driveshaft flanges and slip joints. A plastic or rubber soft-faced hammer should be used to tap on the yoke or bearing cup assembly in order to unseat the bearing cup assembly. You must disconnect the driveshaft from the axle flange by removing and discarding the 4 bolts and the 2 U-joint retainers before supporting the driveshaft with mechanic's wire. The next step requires draining the driveshaft coupling shaft by separating 4 bolts along with 2 U-joint retainers for disposal in addition to driveshaft maintenance support. The rear coupling shaft assembly together with the 2 bearing support bolts must be taken out. Drive the driveshaft yoke removal process by using a plastic or rubber soft-faced hammer on the yoke surface when no pry area is present. You should remove both center bearing support bolts and discard the 4 flange bolts in order to extract the front driveshaft. Wash away grease deposits together with dirt and rust from both driveshaft yoke regions and all driveshaft elements while leaving the driveshaft center bearing bearing and rubber insulator exposed to solvent-free cleaning only. The inspection of the universal joint slip yoke boot should include testing for holes or tears with a replacement boot if necessary and examination of the driveshaft center bearing support for wear or rough action which requires a new support. The front driveshaft installation requires index mark alignment before attaching it to the transmission while using 4 new bolts with hand-only tightening. First install the center support bearing before adding the two bolts while hand-tightening them. The installation requires torquing the 4 driveshaft-to-transmission flange bolts to 100 Nm (74 ft. lbs.) as well as the 2 driveshaft center bearing bolts to 70 Nm (52 ft. lbs.). Position the rear coupling shaft assembly before installing 2 center support bearing bolts that should be tightened with hand pressure. Install the rear coupling shaft assembly to the front driveshaft by using 2 new retainers and 4 driveshaft-to-coupling shaft bolts that require a torque setting of 70 Nm (52 ft. lbs.). When fitting the flange onto the rear axle pinion flange pilot ensure a tight fit before equally tightening all bolts according to a cross pattern. The rear coupling shaft assembly installation ends with attaching it to the rear axle while applying 70 Nm torque to 4 new bolts and 70 Nm torque to 2 center support bearing bolts.