How to service the ABS Control Module, specifically the Electronic Brake Control Module on 2008 Lincoln Navigator?

The service of Electronic Brake Control Module ABS Module should begin with knowledge that Anti-Lock Brake System (ABS) Module calibration pairs with the hydraulic control unit (HCU) on roll stability control (RSC)-equipped vehicles with ABS module interchange between such vehicles prohibited. The ABS module exists independently from the HCU for RSC-equipped vehicles though the installation of a new HCU requires both parts to be fitted as one assembly using latest service parts. To install a new ABS module the system needs configuration through download/upload or as-built data procedures. Start the procedure by removing the battery ground cable to stop damage caused by static electrical discharge. The mass air flow (MAF) sensor electrical connector requires detachment before removing the air cleaner cover retaining clips. Detach the air cleaner outlet clamp and remove the air cleaner cover from the outlet pipe before reinstalling it tightly at 4 Nm (35 lb-in). Three bolts securing the HCU bracket to the frame need to be removed before tightening them to 20 Nm (15 lb-ft) when reinstalling them. Disconnect the ABS electrical connector before you remove four ABS bolts to take out the ABS module assembly and tighten all bolts to 18 lb-in (2 Nm) when reinstalling. Whenimplementing a new ABS module on a vehicle equipped with RSC it is essential to properly set up the module according to specifications.

OEM 2008 Lincoln Navigator ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 ABS Control Modules found

View related parts
2008 Lincoln Navigator Control Module
Part Number: 8L1Z-2C219-D
$643.50 MSRP: $880.00
You Save: $236.50 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Base No.: 2C219
- Item Weight: 3.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L1Z-2C219-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Lincoln Navigator Submodels:
- Base, L | 8 Cyl 5.4 L GAS
View related parts
2008 Lincoln Navigator Control Module
Part Number: 7L1Z-2C219-A
$655.88 MSRP: $896.92
You Save: $241.04 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Base No.: 2C219
- Item Weight: 2.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L1Z-2C219-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Lincoln Navigator Submodels:
- Base, L, L Luxury, L Ultimate, Luxury, Ultimate | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
2008 Lincoln Navigator Control Module
Part Number: 7L1Z-2C219-F
$765.00 MSRP: $1046.15
You Save: $281.15 (27%)
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Replaces: 7L1Z-2C219-D, 7L1Z-2C219-E
- Base No.: 2C219
- Item Weight: 2.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L1Z-2C219-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Lincoln Navigator Submodels:
- Base, L, L Luxury, L Ultimate, Luxury, Ultimate | 8 Cyl 5.4 L GAS
View related parts
2008 Lincoln Navigator Control Module
Part Number: 7L1Z-2C215-A
Product Specifications
- Other Name: Module; ABS Control Module; Modulator Valve
- Base No.: 2C215
- Item Weight: 5.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L1Z-2C215-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Lincoln Navigator Submodels:
- Base, L, L Luxury, L Ultimate, Luxury, Ultimate | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
2008 Lincoln Navigator Control Module
Part Number: 7L1Z-2C405-E
Product Specifications
- Other Name: Unit Assembly - Control; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve; ABS Control Unit
- Replaces: 7L1Z-2C405-D
- Base No.: 2C405
- Item Weight: 8.10 Pounds
- Item Dimensions: 9.0 x 8.1 x 8.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L1Z-2C405-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Lincoln Navigator Submodels:
- Base, L, L Luxury, L Ultimate, Luxury, Ultimate | 8 Cyl 5.4 L GAS
View related parts
2008 Lincoln Navigator Control Module
Part Number: 8L1Z-2C405-B
Product Specifications
- Other Name: Unit Assembly - Control; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve; ABS Control Unit
- Manufacturer Note: Complete Unit HCU And ECU
- Base No.: 2C405
- Item Weight: 8.80 Pounds
- Item Dimensions: 8.6 x 8.5 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L1Z-2C405-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Lincoln Navigator Submodels:
- Base, L | 8 Cyl 5.4 L GAS

2008 Lincoln Navigator ABS Control Module

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2008 Lincoln Navigator ABS Control Module available at FordPartsDeal.com. You can confidently purchase our OEM 2008 Lincoln Navigator ABS Control Module as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2008 Lincoln Navigator ABS Control Module Parts Questions & Experts Answers

Q: How to service the ABS Control Module, specifically the Electronic Brake Control Module on 2008 Lincoln Navigator?
A: The service of Electronic Brake Control Module ABS Module should begin with knowledge that Anti-Lock Brake System (ABS) Module calibration pairs with the hydraulic control unit (HCU) on roll stability control (RSC)-equipped vehicles with ABS module interchange between such vehicles prohibited. The ABS module exists independently from the HCU for RSC-equipped vehicles though the installation of a new HCU requires both parts to be fitted as one assembly using latest service parts. To install a new ABS module the system needs configuration through download/upload or as-built data procedures. Start the procedure by removing the battery ground cable to stop damage caused by static electrical discharge. The mass air flow (MAF) sensor electrical connector requires detachment before removing the air cleaner cover retaining clips. Detach the air cleaner outlet clamp and remove the air cleaner cover from the outlet pipe before reinstalling it tightly at 4 Nm (35 lb-in). Three bolts securing the HCU bracket to the frame need to be removed before tightening them to 20 Nm (15 lb-ft) when reinstalling them. Disconnect the ABS electrical connector before you remove four ABS bolts to take out the ABS module assembly and tighten all bolts to 18 lb-in (2 Nm) when reinstalling. Whenimplementing a new ABS module on a vehicle equipped with RSC it is essential to properly set up the module according to specifications.