How to Remove and Replace the Rear Three-Piece Drive Shaft on 2009 Ford F-250 Super Duty?

The removal process of rear three-piece driveshaft requires your vehicle to be engaged in neutral gear while hoisted up. Index-mark the driveshaft flanges and slip joints. A plastic or rubber soft-faced hammer enables successful unseating of bearing cup assemblies through yoke or bearing cup tapping. Extract the driveshaft from the axle flange through 4 bolt removal followed by U-joint retainer discard then secure the driveshaft with mechanic's wire installation. The driveshaft separation from the coupling shaft requires the removal of 4 mounting bolts together with 2 U-joint retainers as well as the utilization of mechanic's wire to support the driveshaft. The removal process starts by taking out both bearing support bolts and the coupling shaft rear assembly. The driveshaft yoke requires tapping with a plastic or rubber soft-faced hammer before removal of the 4 flange bolts and then 2 center bearing support bolts to extract the front driveshaft. The driveshaft yoke areas along with all driveshaft components need cleaning from grease and dirt and rust before wiping the bearing and rubber insulator of the driveshaft center bearing without submerging it in solvent. Check the slip yoke boot of the U-joint for damages or tears while replacing it if needed to inspect the driveshaft center bearing support for signs of wear and replace it with a new support if required. You should use new bolts for setup when aligning the index marks between the transmission and front driveshaft while keeping the installation torque at minimum. Install two bolts to the center support bearing before completing each step by hand only. Secure 4 driveshaft-to-transmission flange bolts with a torque of 100 Nm (74 lb-ft) while 2 driveshaft center bearing bolts should be tightened to 70 Nm (52 lb-ft). Fits the rear coupling shaft assembly before installing the 2 center support bearing screws with light manual torque. The front driveshaft receives the rear coupling shaft assembly through the installation of 2 new retainers and 4 driveshaft-to-coupling shaft bolts which need torqued to 62 Nm (46 lb-ft). Tighten the bolts gradually across the pattern around the flange until it produces a tight fit with the rear axle pinion flange pilot. The last step involves connecting the rear coupling shaft assembly to the rear axle by installing 4 new bolts which should be tightened to 100 Nm (74 lb-ft) then tighten the 2 rear coupler shaft assembly center support bearing bolts to 70 Nm (52 lb-ft).

OEM 2009 Ford F-250 Super Duty Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

39 Drive Shafts found

View related parts
2009 Ford F-250 Super Duty Axle Shaft, Front Driver Side Part Number: EC3Z-3220-E
$445.71 MSRP: $654.50
You Save: $208.79 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Assembly
- Position: Front Driver Side
- Replaces: AC3Z-3220-B, EC3Z-3220-C, BC3Z-3220-C
- Item Weight: 28.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: EC3Z-3220-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, Platinum, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.4 L DIESEL, 8 Cyl 6.7 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-GZ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 67.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-GZ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: AC3Z-4R602-A
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 7C3Z-4R602-FC, 7C3Z-4R602-BZ
- Base No.: 4R602
- Item Weight: 59.70 Pounds
- Item Dimensions: 25.7 x 6.0 x 15.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: AC3Z-4R602-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4602-BF
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 14.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-BF
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4602-BH
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 23.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-BH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4602-BM
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 43.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-BM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4602-BN
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 41.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4602-BN
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-DT
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 53.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-DT
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-EC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 65.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-EC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-EF
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 70.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-EF
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- XL | 8 Cyl 6.4 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-EZ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 72.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-EZ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-FA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 64.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-GD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 61.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-GD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-GF
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 65.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-GF
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-GL
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 62.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-GL
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-GS
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 65.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-GS
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-GT
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 65.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-GT
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-HB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 68.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-HB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.4 L DIESEL
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-HD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 70.20 Pounds
- Item Dimensions: 79.8 x 10.7 x 8.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-HD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2009 Ford F-250 Super Duty Drive Shaft Part Number: 7C3Z-4R602-HE
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 69.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7C3Z-4R602-HE
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford F-250 Super Duty Submodels:
- Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS

| Page 1 of 2 |Next >

1-20 of 39 Results

2009 Ford F-250 Super Duty Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2009 Ford F-250 Super Duty Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2009 Ford F-250 Super Duty Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2009 Ford F-250 Super Duty Drive Shaft Parts Q&A

Q: How to Remove and Replace the Rear Three-Piece Drive Shaft on 2009 Ford F-250 Super Duty?
A: The removal process of rear three-piece driveshaft requires your vehicle to be engaged in neutral gear while hoisted up. Index-mark the driveshaft flanges and slip joints. A plastic or rubber soft-faced hammer enables successful unseating of bearing cup assemblies through yoke or bearing cup tapping. Extract the driveshaft from the axle flange through 4 bolt removal followed by U-joint retainer discard then secure the driveshaft with mechanic's wire installation. The driveshaft separation from the coupling shaft requires the removal of 4 mounting bolts together with 2 U-joint retainers as well as the utilization of mechanic's wire to support the driveshaft. The removal process starts by taking out both bearing support bolts and the coupling shaft rear assembly. The driveshaft yoke requires tapping with a plastic or rubber soft-faced hammer before removal of the 4 flange bolts and then 2 center bearing support bolts to extract the front driveshaft. The driveshaft yoke areas along with all driveshaft components need cleaning from grease and dirt and rust before wiping the bearing and rubber insulator of the driveshaft center bearing without submerging it in solvent. Check the slip yoke boot of the U-joint for damages or tears while replacing it if needed to inspect the driveshaft center bearing support for signs of wear and replace it with a new support if required. You should use new bolts for setup when aligning the index marks between the transmission and front driveshaft while keeping the installation torque at minimum. Install two bolts to the center support bearing before completing each step by hand only. Secure 4 driveshaft-to-transmission flange bolts with a torque of 100 Nm (74 lb-ft) while 2 driveshaft center bearing bolts should be tightened to 70 Nm (52 lb-ft). Fits the rear coupling shaft assembly before installing the 2 center support bearing screws with light manual torque. The front driveshaft receives the rear coupling shaft assembly through the installation of 2 new retainers and 4 driveshaft-to-coupling shaft bolts which need torqued to 62 Nm (46 lb-ft). Tighten the bolts gradually across the pattern around the flange until it produces a tight fit with the rear axle pinion flange pilot. The last step involves connecting the rear coupling shaft assembly to the rear axle by installing 4 new bolts which should be tightened to 100 Nm (74 lb-ft) then tighten the 2 rear coupler shaft assembly center support bearing bolts to 70 Nm (52 lb-ft).