How to Service the Side Impact Air Bag Sensor on Ford Crown Victoria?

The first step for side impact sensor servicing requires depowering the SRS to minimize accidental deployment risks since memory saver devices may result in fatal injuries or deaths. When executing side impact sensor work on vehicles that experienced a collision check the restraints control module (RCM) and impact sensor installation sites for any shape change before fitting new components which must include both a fresh RCM and sensors regardless of if air bags deployed. The air bag warning indicator operates normally during RCM fuse removal while the ignition switch is ON. This does not indicate any fault condition. The vehicle must return to the customer only when the SRS demonstrates full operational capability along with no detected faults. After part replacement the original component needs reinstallation while conducting another diagnostic test to verify repairs. To begin the procedure start by removing scuff plates from doors then unfasten the B-pillar weather stripping before taking off trim panels beneath the B-pillar. The specified sequence of bolt removal frees up the side impact sensor for disconnection of its electrical connector so the bracketed sensor can be removed. The proper installation requires setting the RCM and impact sensor fasteners at exactly 12 Nm (9 lb-ft) torque since it determines correct device operation. Dress the side impact sensor with bracket while properly connecting its electrical connector before performing the reassembly steps involving alignment and seating of the lower B-pillar trim panel followed by weather stripping attachment and later reinstallation of scuff plates along with the SRS power cycle.

OEM Ford Crown Victoria Air Bag Sensor

Air Bag Impact Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Air Bag Sensors found

View related parts
Ford Crown Victoria Front Impact Sensor Part Number: 3W1Z-14B006-AA
$124.18 MSRP: $171.78
You Save: $47.60 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Sensor; Center Sensor
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Side Impact Sensor, Front Outer Part Number: 6W1Z-14B345-AA
$86.88 MSRP: $120.19
You Save: $33.31 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Side Air Bag; Air Bag Impact Sensor, Front Outer; Air Bag Sensor; Side Sensor
- Manufacturer Note: RH/LH
- Position: Front Outer
- Replaces: 5W1Z-14B345-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2011 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Air Bag Sensor Part Number: 1W1Z-14B006-AA
$112.10 MSRP: $178.00
You Save: $65.90 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; Front Impact Sensor; Front Sensor; Center Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | Base, LWB, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Front Sensor Part Number: F5AZ14B004A
$88.65 MSRP: $122.64
You Save: $33.99 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; Air Bag Sensor; Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Front Sensor Part Number: F2AZ14B004B
$28.61 MSRP: $39.57
You Save: $10.96 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; Air Bag Sensor; Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1994 Ford Crown Victoria | Base, LX, Police Interceptor, S, Touring Sedan | 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Diagnostic Module Part Number: 4W7Z-14B321-AA
$138.33 MSRP: $191.37
You Save: $53.04 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly - Airbag; Sensor Assembly - Air Bag
- Manufacturer Note: Restraint control module and bracket, w/o side air bags, AFTER 11/17/03
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Side Impact Sensor, Front Outer Part Number: 3W7Z-14B345-BB
$28.38 MSRP: $39.26
You Save: $10.88 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Side Air Bag; Air Bag Impact Sensor, Front Outer; Air Bag Sensor; Side Sensor
- Position: Front Outer
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Front Impact Sensor Part Number: 5W1Z-14B004-AA
Product Specifications
- Other Name: Sensor Assembly; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Sensor
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2011 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Air Bag Sensor, Front Part Number: F8AZ-14B005-AA
Product Specifications
- Other Name: Sensor Assembly; Front Impact Sensor; Front Sensor
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Rear Sensor Part Number: F1VY14B007A
Product Specifications
- Other Name: Sensor Assembly; Air Bag Sensor; Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1994 Ford Crown Victoria | Base, LX, Police Interceptor, S, Touring Sedan | 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Diagnostic Module Part Number: 4W7Z-14B321-BA
Product Specifications
- Other Name: Sensor Assembly - Airbag; Sensor Assembly - Air Bag
- Manufacturer Note: Restraint control module and bracket, with side air bags, AFTER 11/17/03
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: 1W7Z-14B321-AC
Product Specifications
- Other Name: Sensor Assembly - Airbag; Diagnostic Module; Sensor Assembly - Air Bag
- Manufacturer Note: Restraint control module and bracket
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | Base, LWB, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS

Ford Crown Victoria Air Bag Sensor

OEM Air Bag Sensor boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Air Bag Sensor with long life and a perfect fit. Come to our website and find genuine Ford Crown Victoria parts. We keep a wide inventory of OEM Crown Victoria parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

It plays a crucial role in raising the safety level of Ford Crown Victoria automobile as well as serves as a prerequisite for other important equipment, namely Air Bag Sensor also called a crash sensor. This Air Bag Sensor is widely used for its performance; it is tasked with the role of sensing an impact in the event of a collision, then Sends a message to the control unit to trigger the air bags hence protecting the passengers. It is also credited for its performance and effectiveness on different Crown Victoria models and is a main component in determining the impact and air bag discharge. The luxury Ford Crown Victoria sedan was first produced in the early part of the century and has gone through many models since then The air bag sensor is still in place since the inception of the Crown Victoria. This small device not only improves the functioning of the vehicle safety features, but also highlights the priority of Ford cars' passengers' safety. In particular, the Air Bag Sensor can be purchased in several versions, thus allowing drivers of the Crown Victoria to use all the protection options. At the same time, the timely deployment of air bags is one of the distinctive features of the sensor in the automotive market, which again confirms the Ford Crown Victoria as a safe and reliable automobile for consumers. Indeed, Ford Crown Victoria Air Bag Sensor offers performance, safety, and durability, which are the hallmarks of Ford car products and the Auto Tech organization.

Ford Crown Victoria Air Bag Sensor Parts and Q&A

Front Impact Sensor
5W1Z-14B004-AA
Q: How to Service the Side Impact Air Bag Sensor on Ford Crown Victoria?
A:
The first step for side impact sensor servicing requires depowering the SRS to minimize accidental deployment risks since memory saver devices may result in fatal injuries or deaths. When executing side impact sensor work on vehicles that experienced a collision check the restraints control module (RCM) and impact sensor installation sites for any shape change before fitting new components which must include both a fresh RCM and sensors regardless of if air bags deployed. The air bag warning indicator operates normally during RCM fuse removal while the ignition switch is ON. This does not indicate any fault condition. The vehicle must return to the customer only when the SRS demonstrates full operational capability along with no detected faults. After part replacement the original component needs reinstallation while conducting another diagnostic test to verify repairs. To begin the procedure start by removing scuff plates from doors then unfasten the B-pillar weather stripping before taking off trim panels beneath the B-pillar. The specified sequence of bolt removal frees up the side impact sensor for disconnection of its electrical connector so the bracketed sensor can be removed. The proper installation requires setting the RCM and impact sensor fasteners at exactly 12 Nm (9 lb-ft) torque since it determines correct device operation. Dress the side impact sensor with bracket while properly connecting its electrical connector before performing the reassembly steps involving alignment and seating of the lower B-pillar trim panel followed by weather stripping attachment and later reinstallation of scuff plates along with the SRS power cycle.