How to service and repair the front brake caliper on Ford Crown Victoria?

At the start of front brake caliper maintenance work only select brake fluid that fulfills manufacturer criteria while always discarding any prior drained fluid to stop damage through contamination. The servicing operation requires first disabling any fire suppression system to minimize safety risks. First remove the tire along with the wheel before you detach the brake caliper flow bolt and discard both copper washers. The service requires removal of two brake guide pin caliper bolts which enables full removal of the brake caliper and disconnects the brake pads. Check the brake caliper as well as guide pins along with locating pins to identify wear or damage; replace the brake caliper with a new components in case of leakage or damage. Keep your focus on seating the guide pin boots directly since incorrect placement may result in brake damage. The installation process requires starting with the lower brake caliper bolt followed by torquing the two guide pin bolts to 36 Nm (27 ft.lbs.) to attach the anchor and caliper plate together. The brake caliper flow bolt needs two new copper washers for installation before it receives a tightening torque of 48 Nm (35 ft. lbs.). When finishing the procedure bleed the brake caliper before installing the wheel and tire. Repower the vehicle while enabling its fire suppression system and check to ensure normal brake performance exists.

How to bleed the brake caliper on Ford Crown Victoria?

The first step to bleed a brake caliper requires using a box end wrench on the disc brake caliper bleeder screw after attaching a rubber drain tube which should be submerged in partially full clean brake fluid. Have your assistant both pump the brake pedal along with maintaining continuous pressure on it. The brake caliper disc bleeder screw should be loosely opened to allow brake fluid to flow before the grip disappears under the assistant's pedal pressure. Complete the clearing process by filling up the brake master cylinder reservoir only when clear fluid with no air bubbles appears. End the bleeder screw tightening process based on the provided brake caliper specifications.

OEM Ford Crown Victoria Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Brake Calipers found

View related parts
Ford Crown Victoria Caliper, Passenger Side Part Number: F5AZ2B120A
$84.95 MSRP: $114.17
You Save: $29.22 (26%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper Part Number: F5AZ2552A
$11.01 MSRP: $15.24
You Save: $4.23 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Brake Caliper Repair Kit; Brake Caliper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Ford Crown Victoria | Base, LX, Police Interceptor, S, Touring Sedan | 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Driver Side Part Number: F8VZ-2B121-AB
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Passenger Side Part Number: F8VZ-2B120-AB
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Rear Part Number: F7AZ-2552-AA
Product Specifications
- Other Name: Housing; Brake Caliper Repair Kit; Brake Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2000 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Driver Side Part Number: F3VY-2V121-ARM
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Passenger Side Part Number: F3VY-2V120-ARM
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Driver Side Part Number: F1VY-2V121-ARM
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1994 Ford Crown Victoria | Base, LX, Police Interceptor, S, Touring Sedan | 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Passenger Side Part Number: F1VY-2V120-ARM
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1994 Ford Crown Victoria | Base, LX, Police Interceptor, S, Touring Sedan | 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Front Driver Side Part Number: 7W7Z-2B121-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Front Driver Side
- Replaces: 6W7Z-2B121-AA, 3W1Z-2B121-AB, 3W7Z-2B121-AA, 6W1Z-2B121-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Front Passenger Side Part Number: 7W7Z-2B120-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Front Passenger Side
- Replaces: 3W1Z-2B120-AB, 6W7Z-2B120-AA, 3W7Z-2B120-AA, 6W1Z-2B120-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Rear Driver Side Part Number: 7W1Z-2553-B
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Rear Passenger Side Part Number: 7W1Z-2552-B
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Driver Side Part Number: 6W7Z-2B121-AA
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pads; Brake Caliper Repair Kit; Brake Caliper
- Position: Driver Side
- Replaced by: 7W7Z-2B121-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Passenger Side Part Number: 6W7Z-2B120-AA
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pads; Brake Caliper Repair Kit; Brake Caliper
- Position: Passenger Side
- Replaced by: 7W7Z-2B120-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Ford Crown Victoria | Police Interceptor | 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper, Passenger Side Part Number: 1W1Z-2B120-AA
Product Specifications
- Other Name: Caliper With Pads; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH - with pads
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | Base, LWB, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Caliper Part Number: YW1Z-2552-BA
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Manufacturer Note: RH & LH Housing less pads
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS

Ford Crown Victoria Brake Caliper

OEM Brake Caliper boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Caliper with long life and a perfect fit. Come to our website and find genuine Ford Crown Victoria parts. We keep a wide inventory of OEM Crown Victoria parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Brake Caliper of Ford Crown Victoria vehicles is one significant part of the vehicles' brake system that is used to clamp the brake pads against the rotors to enable a friction that is needed to bring the vehicles to a halt. These calipers come in two main types: The types of tariffs are: direct, fixed and floating. Clamp type: Fixed calipers make use of two opposing pistons to clamp from the two faces of the disc - this gives improved performance of the tool but has comparatively low tolerance of hardness irregularities. On the other hand, floating calipers are positioned perpendicular to the disc's rotating axis; they work with only one piston that forcefully pushes the internal brake pad and urges the caliper to slide and apply pressure to both ends of the disc. However, floating calipers suffer from this problem due to some reasons and this results into poor fuel consumption, excessive heat in the discs, and variations in pad wear. Concerning the Ford Crown Victoria vehicles, one of the most important components is the brake caliper since it guarantees contraction and silent running. There is also option for more specific type of calipers; replacement calipers, semi-loaded calipers, and loaded calipers. Standard brake calipers are made by the auto manufacturers for their cars and are adequate for normal driving; however, performance brake calipers are better for more stopping power and better performance, particularly if one is a performance driver or a/heavy user. These performance calipers are available in 1-piston and cast 2-piston calipers at a basic or affordable level right up to billet aluminum 8-piston calipers that offer the cyclist the performance improvement and the look.

Ford Crown Victoria Brake Caliper Parts and Q&A

Caliper, Front Driver Side
7W7Z-2B121-A
Q: How to service and repair the front brake caliper on Ford Crown Victoria?
A:
At the start of front brake caliper maintenance work only select brake fluid that fulfills manufacturer criteria while always discarding any prior drained fluid to stop damage through contamination. The servicing operation requires first disabling any fire suppression system to minimize safety risks. First remove the tire along with the wheel before you detach the brake caliper flow bolt and discard both copper washers. The service requires removal of two brake guide pin caliper bolts which enables full removal of the brake caliper and disconnects the Brake Pads. Check the brake caliper as well as guide pins along with locating pins to identify wear or damage; replace the brake caliper with a new components in case of leakage or damage. Keep your focus on seating the guide pin boots directly since incorrect placement may result in brake damage. The installation process requires starting with the lower brake caliper bolt followed by torquing the two guide pin bolts to 36 Nm (27 ft.lbs.) to attach the anchor and caliper plate together. The brake caliper flow bolt needs two new copper washers for installation before it receives a tightening torque of 48 Nm (35 ft. lbs.). When finishing the procedure bleed the brake caliper before installing the wheel and tire. Repower the vehicle while enabling its fire suppression system and check to ensure normal brake performance exists.
Caliper
F6AZ-2552-CA
Q: How to bleed the brake caliper on Ford Crown Victoria?
A:
The first step to bleed a brake caliper requires using a box end wrench on the disc brake caliper bleeder screw after attaching a rubber drain tube which should be submerged in partially full clean brake fluid. Have your assistant both pump the Brake Pedal along with maintaining continuous pressure on it. The brake caliper disc bleeder screw should be loosely opened to allow brake fluid to flow before the grip disappears under the assistant's pedal pressure. Complete the clearing process by filling up the brake master cylinder reservoir only when clear fluid with no air bubbles appears. End the bleeder screw tightening process based on the provided brake caliper specifications.