How to service and repair the upper intake manifold on Ford E-150 Econoline?

Service and repair of the upper intake manifold starts by taking out the air cleaner assembly together with the engine cover. Unload the accelerator cable and speed control cable only when necessary before you dispose of the push pin clip to discard. Remove the IAC valve by disconnecting its electrical connector then pulling out the assembly. The throttle body requires cable removal for both accelerator cable and speed control actuator cable while present. The cables should be disconnected from their cable bracket before removing their spark plug wire holders. Proceed by taking out the 12 upper intake manifold securing bolts. The installation requires a new accelerator control splash shield clip push pin and a gasket check of the intake manifold upper surface so it can be replaced when needed. The bolt installation consists of two steps where initial torque should be set to 6 Nm (53 inch lbs.) followed by a final torque of 10 Nm (89 inch lbs.).

OEM Ford E-150 Econoline Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Intake Manifolds found

View related parts
Ford E-150 Econoline Intake Manifold
Part Number: 2L1Z-9424-AA
$286.02 MSRP: $420.00
You Save: $133.98 (32%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold; Lower Manifold
- Manufacturer Note: Includes valley stuffer 6P013
- Replaces: YL3Z-9424-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2002 Ford E-150 Econoline | Base, XL | 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Upper
Part Number: 1L3Z-9424-AA
$64.58 MSRP: $94.00
You Save: $29.42 (32%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Lower, Upper
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford E-150 Econoline | Base | 6 Cyl 4.2 L GAS
View related parts
Ford E-150 Econoline Intake Manifold
Part Number: YL3Z-9424-EA
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999 Ford E-150 Econoline | Base, XL | 6 Cyl 4.2 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Lower
Part Number: YL3Z-9424-BA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Lower
- Manufacturer Note: Lower, Romeo engine
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000 Ford E-150 Econoline | Base, XL | 8 Cyl 4.6 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Upper
Part Number: YC2Z-9424-CA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2001 Ford E-150 Econoline | Base, XL | 8 Cyl 4.6 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Upper
Part Number: XL3Z-9424-CA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2000 Ford E-150 Econoline | Base, XL | 6 Cyl 4.2 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Lower
Part Number: F85Z-9424-AA
Product Specifications
- Other Name: Housing; Engine Intake Manifold, Lower
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2000 Ford E-150 Econoline | Base, XL | 6 Cyl 4.2 L GAS
View related parts
Ford E-150 Econoline Intake Manifold
Part Number: F75Z-9424-AB
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold; Lower Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford E-150 Econoline | Base, XL | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Econoline Intake Manifold
Part Number: F6TZ9424A
Product Specifications
- Other Name: Manifold Assembly Inlet; Engine Intake Manifold; Upper Manifold; Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996 Ford E-150 Econoline | Base, XL | 8 Cyl 5.0 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Upper
Part Number: F65Z-9424-C
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper
- Manufacturer Note: Upper. Also service detail tube 9D428
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford E-150 Econoline | Base, XL | 8 Cyl 4.6 L GAS
View related parts
Ford E-150 Econoline Intake Manifold
Part Number: F4TZ9424B
Product Specifications
- Other Name: Manifold Assembly Inlet; Engine Intake Manifold; Upper Manifold; Manifold Assembly - Inlet
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Ford E-150 Econoline | Base, XL | 8 Cyl 5.0 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Lower
Part Number: 2L1Z-9424-BA
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford E-150 Econoline | Base | 8 Cyl 4.6 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Upper
Part Number: 1L3Z-9424-BA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford E-150 Econoline | Base | 8 Cyl 4.6 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Lower
Part Number: 1L2Z-9424-AA
Product Specifications
- Other Name: Kit - Manifold Hardware; Engine Intake Manifold, Lower
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford E-150 Econoline | Base | 8 Cyl 4.6 L GAS
View related parts
Ford E-150 Econoline Intake Manifold, Lower
Part Number: 1L1Z-9424-AA
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford E-150 Econoline | Base | 8 Cyl 4.6 L GAS
View related parts
Ford E-150 Econoline Intake Manifold
Part Number: F85Z-9424-BA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Upper Manifold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford E-150 Econoline | Base, XL | 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L GAS

Ford E-150 Econoline Intake Manifold

Welcome to our website where you can discover high-quality, genuine Ford E-150 Econoline Intake Manifold. We offer an extensive inventory of OEM Ford E-150 Econoline Intake Manifold at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Ford E-150 Econoline Intake Manifold Parts Questions & Experts Answers

Intake Manifold
2L1Z-9424-AA
Q: How to service and repair the upper intake manifold on Ford E-150 Econoline?
A: Service and repair of the upper intake manifold starts by taking out the air cleaner assembly together with the engine cover. Unload the Accelerator Cable and speed control cable only when necessary before you dispose of the push pin clip to discard. Remove the IAC valve by disconnecting its electrical connector then pulling out the assembly. The Throttle Body requires cable removal for both accelerator cable and speed control actuator cable while present. The cables should be disconnected from their cable bracket before removing their spark plug wire holders. Proceed by taking out the 12 upper intake manifold securing bolts. The installation requires a new accelerator control splash shield clip push pin and a gasket check of the intake manifold upper surface so it can be replaced when needed. The bolt installation consists of two steps where initial torque should be set to 6 Nm (53 inch lbs.) followed by a final torque of 10 Nm (89 inch lbs.).