How to service the right-hand catalytic converter on all on Ford Edge?

Service of the right-hand catalytic converter for all vehicles involves two possible options for the catalytic converter heat shield fixing. A proper seal requires the use of new fasteners and gaskets together with flange face cleaning before applying new gaskets. When the vehicle has neutral engagement move it onto a hoist before removing the catalyst monitor sensor then the exhaust Y-pipe. Services on cars with all-wheel drive require you to index-mark your driveshaft for reinstallation and afterward remove the four U-joint flange bolts to separate the front driveshaft and use mechanic's wire for securing. Reinstall the driveshaft by tightening its bolts to 70 Nm (52 lb-ft) torque. Proceed to remove the intermediate shaft followed by the two bolts holding the catalytic converter support bracket to the engine block while tightening them to 40 Nm when reinstalling. The shield of a power steering rack must be unfastened by removing its two bolts at a torque of 15 Nm (11 lb-ft) before reinstalling. Detach the catalytic converter support bracket-to-engine block bolt followed by the nut while tightening them to 40 Nm (30 lb-ft) during the reinstallation procedure. When replacing all components you must remove two nuts and the roll restrictor shield afterward torquing these parts to 11 Nm (8 lb-ft). The roll restrictor bolt must be removed then the engine needs to be turned forward before tightening it to 90 Nm (66 lb-ft). Regular tightness should be maintained at 20 Nm (15 lb-ft) when reinstalling the two bracket-to-right-hand catalytic converter bolts. Disassemble the four nuts from the right-hand catalytic converter and discard both the nuts as well as the gasket. The installation of the right-hand catalytic converter requires users to replace and tighten nuts to 40 Nm (30 lb-ft) followed by removal and disposal of all four right-hand catalytic converter-to-exhaust manifold studs while new studs should be torqued to 25 Nm (18 lb-ft). After completing the opposite procedures keep installed a new gasket and replace all nuts and studs.

How to service the LH catalytic converter on Ford Edge?

The servicing of the LH catalytic converter should start with placing the vehicle in neutral on a hoist. Service of the catalytic converter heat shield occurs separately from other components. New fasteners must be used for installation together with clean flange faces before using the new gasket to achieve proper sealing. It is necessary to remove both the exhaust Y-pipe and the catalyst monitor sensor electrical connector. First remove the two bolts which fasten the catalytic converter support bracket to the transmission while you install them tightly at 48 Nm (35 lb-ft). Install new nuts to both catalytic converter ends with 40 Nm (30 lb-ft) torque and throw away the nuts along with the gasket. You should also replace all four LH catalytic converter-to-exhaust manifold studs that need to be tightened to 25 Nm (18 lb-ft). The last step includes the reverse removal method with new gasket installation and nuts and studs placement.

OEM Ford Edge Catalytic Converter

Cat. Converter

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 Catalytic Converters found

View related parts
Ford Edge Catalytic Converter, Passenger Side Part Number: F2GZ-5G232-B
$1239.00 MSRP: $1678.57
You Save: $439.57 (27%)
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter with Integrated Exhaust Manifold, Right; Exhaust Manifold; Manifold W/Converter
- Manufacturer Note: Rear
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Exhaust Manifold, Driver Side Part Number: BT4Z-5G232-C
$745.50 MSRP: $940.00
You Save: $194.50 (21%)
ADD TO CART
Product Specifications
- Other Name: Exhaust Manifold And Catalyst; Catalytic Converter with Integrated Exhaust Manifold, Left; Manifold Converter; Manifold W/Converter; Exhaust Manifold And Catalyst Assembly; Catalytic Converter
- Position: Driver Side
- Replaces: BT4Z-5G232-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | Limited, SE, SEL, Sport | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Ford Edge Catalytic Converter, Front Driver Side Part Number: 7T4Z-5E213-A
$777.00 MSRP: $1050.00
You Save: $273.00 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left, Right
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Ford Edge | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Catalytic Converter Part Number: DT4Z-5E212-A
$1149.00 MSRP: $1445.71
You Save: $296.71 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2013 Ford Edge | Limited, SE, SEL | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Catalytic Converter, Passenger Side Part Number: 7T4Z-5E212-A
$894.75 MSRP: $1122.86
You Save: $228.11 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left, Right
- Manufacturer Note: Rear
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Ford Edge | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Catalytic Converter Part Number: EB5Z-5E212-A
$1066.88 MSRP: $1341.43
You Save: $274.55 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Manifold W/Converter
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Edge | Limited, SE, SEL | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Catalytic Converter, Passenger Side Part Number: F2GZ-5E212-B
$656.48 MSRP: $820.29
You Save: $163.81 (20%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2017 Ford Edge | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Catalytic Converter, Front Driver Side Part Number: 9T4Z-5E213-B
$485.36 MSRP: $604.29
You Save: $118.93 (20%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010 Ford Edge | Limited, SE, SEL, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Catalytic Converter Part Number: G2GZ-5E212-A
$1551.19 MSRP: $1956.43
You Save: $405.24 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | SE, SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Catalytic Converter, Driver Side Part Number: F2GZ-5E213-B
$718.05 MSRP: $905.14
You Save: $187.09 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2017 Ford Edge | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Catalytic Converter Part Number: L2GZ-5E212-A
$1073.63 MSRP: $1350.00
You Save: $276.37 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly
- Replaces: K2GZ-5E212-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2024 Ford Edge | SE, SEL, ST-Line, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Catalytic Converter, Passenger Side Part Number: F2GZ-5E212-H
$837.38 MSRP: $1050.00
You Save: $212.62 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Right
- Position: Passenger Side
- Replaces: F2GZ-5E212-D, F2GZ-5E212-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2024 Ford Edge | Sport, ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Catalytic Converter Part Number: F2GZ-5E212-A
$645.00 MSRP: $805.71
You Save: $160.71 (20%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2016 Ford Edge | SE, SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Catalytic Converter Part Number: G2GZ-5E212-B
$871.13 MSRP: $1092.86
You Save: $221.73 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | SE, SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Catalytic Converter, Passenger Side Part Number: F2GZ-5E212-G
$713.63 MSRP: $892.86
You Save: $179.23 (21%)
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Right
- Position: Passenger Side
- Replaces: F2GZ-5E212-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | Sport, ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Catalytic Converter, Driver Side Part Number: F2GZ-5E213-G
$1006.39 MSRP: $1271.29
You Save: $264.90 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left
- Position: Driver Side
- Replaces: F2GZ-5E213-D, F2GZ-5E213-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2024 Ford Edge | Sport, ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Catalytic Converter Part Number: 7T4Z-5E212-BC
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left
- Manufacturer Note: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007 Ford Edge | SE, SEL, SEL Plus | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Catalytic Converter, Passenger Side Part Number: 9T4Z-5E212-B
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Right
- Manufacturer Note: Rear
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010 Ford Edge | Limited, SE, SEL, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Catalytic Converter, Front Part Number: 7T4Z-5E213-BC
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Right
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007 Ford Edge | SE, SEL, SEL Plus | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Catalytic Converter, Driver Side Part Number: F2GZ-5E213-F
$694.88 MSRP: $875.71
You Save: $180.83 (21%)
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left
- Position: Driver Side
- Replaces: F2GZ-5E213-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | Sport, ST | 6 Cyl 2.7 L GAS

| Page 1 of 2 |Next >

1-20 of 22 Results

Ford Edge Catalytic Converter

OEM Catalytic Converter boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Catalytic Converter with long life and a perfect fit. Come to our website and find genuine Ford Edge parts. We keep a wide inventory of OEM Edge parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Catalytic Converter is among the most key parts of the emission system fitted in Ford Edge passenger cars, which helps change dangerous gases like Carbon Monoxide, Hydrocarbons, and Oxides of Nitrogen into less hazardous gases like water, Carbon Dioxide, and Nitrogen. This device has several noble metals such as platinum, palladium, rhodium and others that act as a catalysts meaning that the substances are used in a chemical reaction but they are not themselves changed. Various models of Catalytic Converters have been applied in the past, recent designs include an interior made up of honeycomb for proper catalytic activity with the emission gases. Ford Edge gives a high flow performance converter to allow the maximum capability for the engine, with the availability of the direct or universal converter kits. These converters are of importance in minimizing emission of hazardous gases and discharge of fumes to the atmospheres in conformance to standard requirements.

Ford Edge Catalytic Converter Parts and Q&A

Catalytic Converter, Passenger Side
7T4Z-5E212-A
Q: How to service the right-hand catalytic converter on all on Ford Edge?
A:
Service of the right-hand catalytic converter for all vehicles involves two possible options for the catalytic converter heat shield fixing. A proper seal requires the use of new fasteners and gaskets together with flange face cleaning before applying new gaskets. When the vehicle has neutral engagement move it onto a hoist before removing the catalyst monitor sensor then the exhaust Y-pipe. Services on cars with all-wheel drive require you to index-mark your driveshaft for reinstallation and afterward remove the four U-joint flange bolts to separate the front driveshaft and use mechanic's wire for securing. Reinstall the driveshaft by tightening its bolts to 70 Nm (52 lb-ft) torque. Proceed to remove the intermediate shaft followed by the two bolts holding the catalytic converter support bracket to the engine block while tightening them to 40 Nm when reinstalling. The shield of a power steering rack must be unfastened by removing its two bolts at a torque of 15 Nm (11 lb-ft) before reinstalling. Detach the catalytic converter support bracket-to-engine block bolt followed by the nut while tightening them to 40 Nm (30 lb-ft) during the reinstallation procedure. When replacing all components you must remove two nuts and the roll restrictor shield afterward torquing these parts to 11 Nm (8 lb-ft). The roll restrictor bolt must be removed then the engine needs to be turned forward before tightening it to 90 Nm (66 lb-ft). Regular tightness should be maintained at 20 Nm (15 lb-ft) when reinstalling the two bracket-to-right-hand catalytic converter bolts. Disassemble the four nuts from the right-hand catalytic converter and discard both the nuts as well as the gasket. The installation of the right-hand catalytic converter requires users to replace and tighten nuts to 40 Nm (30 lb-ft) followed by removal and disposal of all four right-hand catalytic converter-to-exhaust manifold studs while new studs should be torqued to 25 Nm (18 lb-ft). After completing the opposite procedures keep installed a new gasket and replace all nuts and studs.
Catalytic Converter, Front Driver Side
7T4Z-5E213-A
Q: How to service the LH catalytic converter on Ford Edge?
A:
The servicing of the LH catalytic converter should start with placing the vehicle in neutral on a hoist. Service of the catalytic converter heat shield occurs separately from other components. New fasteners must be used for installation together with clean flange faces before using the new gasket to achieve proper sealing. It is necessary to remove both the exhaust Y-pipe and the catalyst monitor sensor electrical connector. First remove the two bolts which fasten the catalytic converter support bracket to the transmission while you install them tightly at 48 Nm (35 lb-ft). Install new nuts to both catalytic converter ends with 40 Nm (30 lb-ft) torque and throw away the nuts along with the gasket. You should also replace all four LH catalytic converter-to-exhaust manifold studs that need to be tightened to 25 Nm (18 lb-ft). The last step includes the reverse removal method with new gasket installation and nuts and studs placement.