How to Service and Repair the Engine Front Timing Cover on Ford Escape?

The process to fix an engine front cover requires dirt-free conditions because dirt spots may lead to engine failure. Placing the vehicle on a hoist in neutral position should begin every service process followed by evacuation of fuel system pressure. Start by disconnecting the ground cable from the battery then strip the crankshaft front seal while removing five bolts, pin-type retainer and the RH lower splash shield. The service procedure begins by removing the generator upper air duct bolt along with the air duct before continuing with removal of the generator shield pin-type retainer followed by its bolt and shield. Start by detaching the 2 generator bolts and the generator stud along with nut before setting the generator to the side. First detach the LH and RH valve covers along with the engine support insulator then proceed to eliminate the accessory drive belt tensioner bolt and the idler pulley bolt. Following HO2S electrical connector bracket nut removal you should set the bracket aside before disconnecting CMP and CKP sensor electrical connectors. The power steering pump requires removal of 3 bolts which should keep the power steering pressure tube bolt installed in the pump housing as you place the pump aside. Then set aside the speed control actuator after you remove its 3 nuts when equipped. Disassemble the 2 oil pan-to-front cover bolts followed by removing all 13 bolts together with 3 stud bolts which requires discarding the gaskets. Induce new gaskets by cleaning all sealing surfaces with metal surface cleaner through application of a plastic scraping tool. Use 6 mm (0.23 inch) diameter dots of silicone gasket and sealer on the cylinder block surfaces and lower cylinder block and cylinder head and oil pan mating areas before installing the engine front cover and tightening its bolts within four minutes post-sealing. Install the engine front cover onto its proper position and use a specified bolt sequence to tighten them to 25 Nm (18 ft. lbs.) before torquing the 2 oil pan-to-front cover bolts to the same force. Draining the engine oil requires uninstalling the oil pan plug before reinstallation with a torque of 26 Nm (19 ft. lbs.). Place the power steering pump in its correct position before you install the 3 bolts and apply torque of 25 Nm (18 ft. lbs.). Connect the HO2S bracket with its nut secured at 10 Nm (89 inch lbs.) after joining the CMP and CKP electrical connectors. First, tighten the idler pulley bolt to 25 Nm (18 ft. lbs.) while installing the pulley and next fasten the accessory drive belt tensioner with its bolt to 45 Nm (33 ft. lbs.). The speed control actuator and its 3 nuts should be installed next to the LH and RH valve covers and engine support insulator. Secure the generator by tightening both its stud to 7 Nm (62 inch lbs.) and stud nut to 47 Nm (35 ft. lbs.) then torque the 2 generator bolts to the same value. Place the generator shield and bolt together with the pin-type retainer then fasten these elements to 4 Nm (35 inch lbs.). After that add the generator upper air duct along with its bolt and secure them to 4 Nm (35 inch lbs.). Finally you should install the RH lower splash shield by tightening its 5 bolts and pin-type retainer to 8 Nm (71 inch lbs.), then reinstall the crankshaft front seal, fill the engine with clean engine oil before reconnecting the battery ground cable.

OEM Ford Escape Timing Cover

Engine Timing Cover

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Timing Covers found

View related parts
Ford Escape Timing Cover, Front Part Number: 5S7Z-6019-A
$119.42 MSRP: $165.20
You Save: $45.78 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Replaces: 1S7Z-6019-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Escape | Limited, XLS, XLT | 6 Cyl 3.0 L GAS
View related parts
Ford Escape Timing Cover, Front Upper Part Number: BM5Z-6019-C
$82.25 MSRP: $119.72
You Save: $37.47 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Upper; Front Cover
- Position: Front Upper
- Replaces: BM5Z-6019-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Escape | SE, SEL, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: 9E5Z-6019-B
$127.21 MSRP: $185.17
You Save: $57.96 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Manufacturer Note: Use RTV Silicone Sealer In Place Of Gasket For This Application. Refer To Workshop Manual For Specification
- Position: Front
- Replaces: 9E5Z-6019-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.5 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: 2L8Z-6019-AA
$122.93 MSRP: $178.93
You Save: $56.00 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford Escape | Hybrid, XLS, XLT, XLT No Boundaries | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: 9L8Z-6019-A
$152.40 MSRP: $221.83
You Save: $69.43 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Ford Escape | Limited, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: K2GZ-6019-H
$138.55 MSRP: $201.67
You Save: $63.12 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Replaced by: K2GZ-6019-L
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022 Ford Escape | SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Front Cover Part Number: P2GZ-6019-A
$129.73 MSRP: $188.83
You Save: $59.10 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Cylinder Front
- Position: Front
- Replaced by: P2GZ-6019-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2023 Ford Escape | Platinum, ST-Line Elite, ST-Line Select | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: JX6Z-6019-E
$147.36 MSRP: $214.50
You Save: $67.14 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2022 Ford Escape | S, SE, SEL | 3 Cyl 1.5 L GAS
View related parts
Ford Escape Valve Cover, Front Part Number: K2GZ-6019-B
$52.77 MSRP: $75.50
You Save: $22.73 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover Assembly - Cylinder Head Front; Engine Cover; Timing Cover; Front Cover; Lower Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2022 Ford Escape | SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Valve Cover, Front Part Number: LX6Z-6019-B
$133.51 MSRP: $194.33
You Save: $60.82 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Timing Cover; Front Cover
- Position: Front
- Replaces: LX6Z-6019-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2023 Ford Escape | Platinum Hybrid, Plug-In Hybrid, SE Hybrid, SE Plug-In Hybrid, SE Sport Hybrid, SEL Hybrid, SEL Plug-In Hybrid, ST-Line Elite Hybrid, ST-Line Hybrid, ST-Line Select Hybrid, Titanium Hybrid, Titanium Plug-In Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Timing Cover, Front Part Number: PV4Z-6019-A
$144.84 MSRP: $210.83
You Save: $65.99 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Cylinder Front; Front Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2023 Ford Escape | Active, Base, ST-Line | 3 Cyl 1.5 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: CJ5Z-6019-D
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Replaces: CJ5Z-6019-A, CJ5Z-6019-B, CJ5Z-6019-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Escape | SE, SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Timing Cover, Front Center Part Number: F8CZ-6019-CA
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Center, Lower Outer; Front Cover; Outer Timing Cover
- Position: Front Center
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: 5M6Z-6019-AA
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2012 Ford Escape | Hybrid, Limited Hybrid, XLS, XLT | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Escape Timing Cover, Front Part Number: CV6Z-6019-B
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Replaces: CV6Z-6019-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Escape | S, SE | 4 Cyl 2.5 L GAS
View related parts
Ford Escape Timing Cover, Front Inner Part Number: YS4Z-6019-AA
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Front Inner, Lower; Front Cover
- Manufacturer Note: Front Inner
- Position: Front Inner
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: 8L8Z-6019-A
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Escape | Limited, XLT | 6 Cyl 3.0 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: 5L8Z-6019-A
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Replaces: 4L8Z-6019-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 6 Cyl 3.0 L GAS
View related parts
Ford Escape Timing Cover, Front Part Number: K2GZ-6019-C
Product Specifications
- Other Name: Cover - Cylinder Front; Engine Timing Cover; Front Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2022 Ford Escape | SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Escape Timing Cover, Front Upper Outer Part Number: YS4Z-6019-DA
Product Specifications
- Other Name: Cover - Timing Belt; Engine Timing Cover, Upper, Upper Outer; Front Cover; Inner Timing Cover
- Manufacturer Note: Outer Upper
- Position: Front Upper Outer
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.0 L GAS

Ford Escape Timing Cover

OEM Timing Cover boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Timing Cover with long life and a perfect fit. Come to our website and find genuine Ford Escape parts. We keep a wide inventory of OEM Escape parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Timing Cover for Ford Escape is extremely important when it comes to protecting the engine timing assembly that can comprise of the timing belt, timing chain or the cam belt. Made of strong material like Aluminum, plastic, steel etc. time cover shields those delicate parts by covering them and preventing access by debris. Some of the Ford Escape Timing Covers have been designed to include gaskets that go further in protecting the timing belt. In the Ford Escape models, different styles of Timing Covers have been used in the course of years with the aim to offer maximum durability and protection. Even so, ordinary and thick Timing Covers do not last a lifetime and may require replacement so as to ensure that any vehicle, Ford Escape in particular, is safe for use on the roads.

Ford Escape Timing Cover Parts and Q&A

Timing Cover, Front
2L8Z-6019-AA
Q: How to Service and Repair the Engine Front Timing Cover on Ford Escape?
A:
The process to fix an engine front cover requires dirt-free conditions because dirt spots may lead to engine failure. Placing the vehicle on a hoist in neutral position should begin every service process followed by evacuation of fuel system pressure. Start by disconnecting the ground cable from the battery then strip the crankshaft front seal while removing five bolts, pin-type retainer and the RH lower splash shield. The service procedure begins by removing the generator upper Air Duct bolt along with the air duct before continuing with removal of the generator shield pin-type retainer followed by its bolt and shield. Start by detaching the 2 generator bolts and the generator stud along with nut before setting the generator to the side. First detach the LH and RH valve covers along with the engine support insulator then proceed to eliminate the accessory drive belt tensioner bolt and the idler pulley bolt. Following HO2S electrical connector bracket nut removal you should set the bracket aside before disconnecting CMP and CKP sensor electrical connectors. The power steering pump requires removal of 3 bolts which should keep the power steering pressure tube bolt installed in the pump housing as you place the pump aside. Then set aside the speed control actuator after you remove its 3 nuts when equipped. Disassemble the 2 Oil Pan-to-front cover bolts followed by removing all 13 bolts together with 3 stud bolts which requires discarding the gaskets. Induce new gaskets by cleaning all sealing surfaces with metal surface cleaner through application of a plastic scraping tool. Use 6 mm (0.23 inch) diameter dots of silicone gasket and sealer on the cylinder block surfaces and lower cylinder block and cylinder head and oil pan mating areas before installing the engine front cover and tightening its bolts within four minutes post-sealing. Install the engine front cover onto its proper position and use a specified bolt sequence to tighten them to 25 Nm (18 ft. lbs.) before torquing the 2 oil pan-to-front cover bolts to the same force. Draining the engine oil requires uninstalling the oil pan plug before reinstallation with a torque of 26 Nm (19 ft. lbs.). Place the power steering pump in its correct position before you install the 3 bolts and apply torque of 25 Nm (18 ft. lbs.). Connect the HO2S bracket with its nut secured at 10 Nm (89 inch lbs.) after joining the CMP and CKP electrical connectors. First, tighten the idler pulley bolt to 25 Nm (18 ft. lbs.) while installing the pulley and next fasten the accessory drive belt tensioner with its bolt to 45 Nm (33 ft. lbs.). The speed control actuator and its 3 nuts should be installed next to the LH and RH valve covers and engine support insulator. Secure the generator by tightening both its stud to 7 Nm (62 inch lbs.) and stud nut to 47 Nm (35 ft. lbs.) then torque the 2 generator bolts to the same value. Place the generator shield and bolt together with the pin-type retainer then fasten these elements to 4 Nm (35 inch lbs.). After that add the generator upper air duct along with its bolt and secure them to 4 Nm (35 inch lbs.). Finally you should install the RH lower splash shield by tightening its 5 bolts and pin-type retainer to 8 Nm (71 inch lbs.), then reinstall the crankshaft front seal, fill the engine with clean engine oil before reconnecting the battery ground cable.