Other Name: Remanufactured Pump Assembly - Power Steering; Pump Assembly - Power Steering
Manufacturer Note: Tag ID: HBD-DF, HBD-GG, Blue, Police, taxi, fleet
Replaces: F85Z-3A674-AARM
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
Fits the following Vehicles:
1997-2001 Ford F-150 | Base, Harley-Davidson Edition, King Ranch, Lariat, Lightning, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
Fits the following Vehicles:
2004-2008 Ford F-150 | FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Limited, STX, THE 60TH ANNIVERSARY EDITION, XL, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
Other Name: Remanufactured Pump Assembly - Power Steering
Replaces: 2L3Z-3A674-AARM
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
Fits the following Vehicles:
2002-2004 Ford F-150 | FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
Other Name: Remanufactured Pump Assembly - Power Steering; Pump Assembly - Power Steering
Replaces: STP-230, 9L3Z-3A674-B
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
Fits the following Vehicles:
2009 Ford F-150 | FX4, King Ranch, Lariat, Platinum, STX, XL, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L FLEX
Ford F-150 Power Steering Pump
Welcome to our website where you can discover high-quality, genuine Ford F-150 Power Steering Pump. We offer an extensive inventory of OEM Ford F-150 Power Steering Pump at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.
Ford F-150 Power Steering Pump Parts Questions & Experts Answers
Q: How to service and repair the power steering pump on Ford F-150?
A: A proper power steering pump service begins with disassembly of the power steering pump pulley. A proper suction device should be used to remove power steering fluid from the reservoir. You must detach the clamp then disconnect the power steering pump supply hose followed by removing and tightening the pressure line bracket-to-engine nut to 40 Nm (30 lb-ft) for the 5.4L engine and 12 Nm (106 lb-in) for the 4.6L engine when reinstalling. Stop and remove the pressure line-to-pump fitting which comes with a Teflon(R) seal that needs disposal and should have a torque of 65 Nm (48 lb-ft) during reinstallation. The power steering pump stud bolt needs removal after disconnecting the oil pressure sending unit wire harness retainer from the power steering pump stud. Torque specifications are 25 Nm (18 lb-ft) for both installation and removal. The power steering pump requires its two bolts removed from underneath the hood while the pump itself follows before installing back the bolts to 25 Nm (18 lb-ft) torques. When disconnecting the power steering pump lines install a new Teflon(R) seal through correct installation using the Teflon(R) Seal Installer Set on the pressure line-to-pump fitting. Completing the service requires performing a power steering system fill operation.