How to remove and replace the rear bumper cover on Ford Flex?

A technician should perform bumper cover replacement when the vehicle sits on a hoist with its transmission shifting to neutral. Regularize these procedures when changing the rear bumper cover. You must first remove the rear tail lamps then you must remove all six rear bumper cover wheelhouse screws that are distributed evenly across the three positions on each side. Finish by tightening these screws to 2 Nm (18 lb-in). Remove first the pair of scrivets situated beside the license plate behind the bumper cover before proceeding to detach the five scrivets running across the lower luggage opening. The process of bumper cover removal requires detaching it from both left-hand and right-hand mounting reinforcement points as you gently stretch the upper rear area away from its mounting position. Detach the rear parking aid electrical connector harness from the bumper cover since these components need to stay mounted on the cover before removing it. Check for damages on the bumper cover mounting reinforcements after removal then replace any broken parts. The installation of the new bumper cover follows the steps for removing it in reverse order.

How to remove and replace the front bumper cover on Ford Flex?

Cautiously remove and install the front bumper cover only when your vehicle is in neutral position on a hoist. Start by disconnecting the 4 upper front bumper cover scrivets followed by the 2 upper front bumper cover bolts then tighten their bolts to 6 Nm (53 lb-in) when reinstalling. The second step involves extracting the 2 front bumper cover scrivets which are situated beneath the license plate area. Remove the front lower air deflector with the bumper cover since you will need to also take out the 3 lower air deflector-to-radiator grille support scrivets. The 3 sets of 2 Nm (18 lb-in) tightened screws secure the front bumper cover wheel house along each side of the vehicle while removing the screws requires 6 pieces. The installation requires disconnecting the fog lamps and front parking aid electrical connectors only when fitted. The operation for releasing the bumper cover begins with a pull motion toward the rear upper side of the bumper cover mounting reinforcement while disassembling the part. Examine the bumper cover mounting reinforcements for harm before deciding on replacement if needed. Reinstallation of a new bumper cover begins with returning components to their original positions during removal while following the opposite steps to install the new component.

OEM Ford Flex Bumper Cover

Bumper Shell

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Bumper Covers found

View related parts
Ford Flex Bumper Cover, Front Part Number: DA8Z-17D957-JPTM
$582.70 MSRP: $924.92
You Save: $342.22 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Manufacturer Note: Paint to match
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Flex | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Flex Bumper Cover, Front Part Number: AA8Z-17D957-KPTM
$324.27 MSRP: $616.33
You Save: $292.06 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Manufacturer Note: Paint to match
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Flex | Limited, SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Flex Bumper Cover, Rear Part Number: DA8Z-17K835-SPTM
$193.48 MSRP: $301.37
You Save: $107.89 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Replaces: DA8Z-17K835-MPTM, DA8Z-17K835-NPTM, AA8Z-17K835-PPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Flex | Base, Executive, Limited, SE, SEL, Titanium | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Ford Flex Bumper Cover, Rear Part Number: DA8Z-17K835-TPTM
$563.22 MSRP: $834.40
You Save: $271.18 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Replaces: AA8Z-17K835-RPTM, DA8Z-17K835-PPTM, DA8Z-17K835-RPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Flex | Base, Executive, Limited, SE, SEL, Titanium | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Ford Flex Bumper Cover, Rear Part Number: 8A8Z-17K835-BPTM
$216.72 MSRP: $318.23
You Save: $101.51 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Ford Flex | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Flex Bumper Cover, Rear Part Number: AA8Z-17K835-NPTM
$236.43 MSRP: $347.18
You Save: $110.75 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Flex | Limited, SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Flex Bumper Cover, Rear Part Number: 8A8Z-17K835-APTM
$349.16 MSRP: $512.72
You Save: $163.56 (32%)
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Ford Flex | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Flex Bumper Cover, Rear Part Number: AA8Z-17K835-MPTM
$380.00 MSRP: $558.00
You Save: $178.00 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Flex | Limited, SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Flex Bumper Cover, Front Part Number: 8A8Z-17D957-APTM
$354.86 MSRP: $521.08
You Save: $166.22 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Ford Flex | Limited, SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Flex Bumper Cover, Front Part Number: DA8Z-17D957-APTM
$643.96 MSRP: $954.02
You Save: $310.06 (33%)
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Manufacturer Note: Paint to match
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Flex | Limited, SE, SEL | 6 Cyl 3.5 L GAS

Ford Flex Bumper Cover

OEM Bumper Cover boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Bumper Cover with long life and a perfect fit. Come to our website and find genuine Ford Flex parts. We keep a wide inventory of OEM Flex parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Flex Bumper Cover is an outer panel that hides the true bumper, refreshes the exterior look, and can absorb some impact shock. The Bumper Cover is built of tough molded skin that serves to smooth the body surface and possibly direct airflow. The integrated openings allow cooling air to reach the radiator or other heat exchangers. The Bumper Cover are dedicated cavities for fog lights, parking lamps, turn signals, license plates, and sensors. The use of small removable covers or inserts is employed for hiding the anchors for the tow-hook or the light pockets that are unused, giving the surface a clean look when the unit is not in use. There are two position-specific types: a front unit shaped to the vehicle's nose and a rear unit shaped to the tail, each designed for their impact area. Every Ford Flex Bumper Cover is engineered according to original specifications so you can install the Bumper Cover directly and easily, with no other modifications needed, and restore the precise fit and visual continuity you expect on a Ford Flex, whether the part is replacing damaged front panels or refreshing the rear of another Ford Flex.

Ford Flex Bumper Cover Parts and Q&A

Bumper Cover, Rear
8A8Z-17K835-APTM
Q: How to remove and replace the rear bumper cover on Ford Flex?
A:
A technician should perform bumper cover replacement when the vehicle sits on a hoist with its transmission shifting to neutral. Regularize these procedures when changing the rear bumper cover. You must first remove the rear tail lamps then you must remove all six rear bumper cover wheelhouse screws that are distributed evenly across the three positions on each side. Finish by tightening these screws to 2 Nm (18 lb-in). Remove first the pair of scrivets situated beside the license plate behind the bumper cover before proceeding to detach the five scrivets running across the lower luggage opening. The process of bumper cover removal requires detaching it from both left-hand and right-hand mounting reinforcement points as you gently stretch the upper rear area away from its mounting position. Detach the rear parking aid electrical connector harness from the bumper cover since these components need to stay mounted on the cover before removing it. Check for damages on the bumper cover mounting reinforcements after removal then replace any broken parts. The installation of the new bumper cover follows the steps for removing it in reverse order.
Bumper Cover, Front
8A8Z-17D957-APTM
Q: How to remove and replace the front bumper cover on Ford Flex?
A:
Cautiously remove and install the front bumper cover only when your vehicle is in neutral position on a hoist. Start by disconnecting the 4 upper front bumper cover scrivets followed by the 2 upper front bumper cover bolts then tighten their bolts to 6 Nm (53 lb-in) when reinstalling. The second step involves extracting the 2 front bumper cover scrivets which are situated beneath the license plate area. Remove the front lower Air Deflector with the bumper cover since you will need to also take out the 3 lower air deflector-to-radiator grille support scrivets. The 3 sets of 2 Nm (18 lb-in) tightened screws secure the front bumper cover wheel house along each side of the vehicle while removing the screws requires 6 pieces. The installation requires disconnecting the fog lamps and front parking aid electrical connectors only when fitted. The operation for releasing the bumper cover begins with a pull motion toward the rear upper side of the bumper cover mounting reinforcement while disassembling the part. Examine the bumper cover mounting reinforcements for harm before deciding on replacement if needed. Reinstallation of a new bumper cover begins with returning components to their original positions during removal while following the opposite steps to install the new component.