How to service and repair the right-hand camshaft on Ford Fusion?

You must start with timing drive component removal when you need to work on the right-hand camshaft. The technicians should verify that camshafts maintain neutral position before extracting bearing caps and need to stop the camshaft from rotating during removal of variable camshaft timing (VCT) actuator. A 3/8-inch ratchet extension in the D-slot on the rear intake camshaft should be used to hold it in position so the VCT actuator bolt can be removed along with the actuator. The cylinder head camshaft bearing caps receive numbered identification for organized installation; when numbers are obscured the caps should be marked prior to disassembly. You should begin your removal operation by taking out the thrust caps (5R and 1R) since they need to be detached first to prevent damaging the components. Start by equally loosening bolts per their specified sequence before extracting the thrust caps and proceeding to the remaining camshaft bearing caps and finally extracting the camshafts from the cylinder head. The VCT actuator ought to be positioned onto the intake camshaft prior to bolt installation which should begin with just sufficient finger pressure. The operation will start by applying clean engine oil to the camshafts before carefully putting them onto the cylinder head while maintaining their neutral position. Engine damage prevention occurs when camshaft caps stay in their original positions while the installation of thrust caps must wait until all bearing caps are present to prevent damage. Apply lubrication to the camshaft bearing caps surface then place them loosely onto the engine parts before adding the loosely installed thrust caps. Install the camshaft bearing cap bolts at 10 Nm (89 inch lbs.) while following the specified installation order. When tightening the VCT actuator bolt maintain the camshaft in neutral position by using a ratchet and extension as a fixture to secure it. To complete the installation process fasten the VCT actuator bolt to 40 Nm (30 ft. lbs.) while applying an additional 90 degrees rotation and reinstall all timing drive components.

OEM Ford Fusion Camshaft

Cam

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

30 Camshafts found

View related parts
Ford Fusion Intake Camshaft Part Number: BB5Z-6250-B
$67.01 MSRP: $97.53
You Save: $30.52 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Manufacturer Note: Intake
- Replaces: BB5Z-6250-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2015 Ford Fusion | SE, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Fusion Camshaft, Passenger Side Part Number: 9L8Z-6250-A
$106.52 MSRP: $147.36
You Save: $40.84 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: RH Intake Camshaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | SE, SEL | 6 Cyl 3.0 L FLEX
View related parts
Ford Fusion Intake Camshaft Part Number: CT1Z-6250-A
$76.64 MSRP: $94.78
You Save: $18.14 (20%)
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Manufacturer Note: Intake
- Replaces: 7G9Z-6250-B, 7G9Z-6250-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2020 Ford Fusion | S, SE, SEL | 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Intake Camshaft Part Number: DS7Z-6250-A
$421.99 MSRP: $619.67
You Save: $197.68 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Manufacturer Note: Intake
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum Hybrid, S Hybrid, SE Hybrid, SEL Hybrid, Titanium Hybrid | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Fusion Camshaft Seal Part Number: FT4Z-6250-J
$134.24 MSRP: $207.17
You Save: $72.93 (36%)
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Replaces: FT4Z-6250-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Camshaft Seal, Driver Side Part Number: FT4Z-6250-D
$95.85 MSRP: $139.52
You Save: $43.67 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Manufacturer Note: LH Exhaust Camshaft
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Camshaft Part Number: 5M8Z-6250-AA
$524.42 MSRP: $725.48
You Save: $201.06 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: Intake
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS
View related parts
Ford Fusion Camshaft, Passenger Side Part Number: 9L8Z-6250-C
$104.71 MSRP: $144.86
You Save: $40.15 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Manufacturer Note: RH Exhaust Camshaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | SE, SEL | 6 Cyl 3.0 L FLEX
View related parts
Ford Fusion Exhaust Camshaft Part Number: AG9Z-6250-C
$157.12 MSRP: $194.33
You Save: $37.21 (20%)
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Manufacturer Note: Exhaust
- Replaces: AG9Z-6250-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2015 Ford Fusion | SE, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Fusion Camshaft Seal, Passenger Side Part Number: FT4Z-6250-C
$135.43 MSRP: $209.00
You Save: $73.57 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Manufacturer Note: RH Exhaust Camshaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Exhaust Camshaft Part Number: FB5Z-6250-B
$121.67 MSRP: $177.10
You Save: $55.43 (32%)
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Manufacturer Note: Exhaust
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2020 Ford Fusion | Platinum, SE, SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Fusion Camshaft Seal, Driver Side Part Number: FT4Z-6250-B
$99.12 MSRP: $152.53
You Save: $53.41 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft
- Manufacturer Note: LH Intake Camshaft
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Camshaft, Passenger Side Part Number: 7T4Z-6250-A
Product Specifications
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Camshaft, Driver Side Part Number: 9L8Z-6250-D
Product Specifications
- Manufacturer Note: LH Exhaust Camshaft
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | SE, SEL | 6 Cyl 3.0 L FLEX
View related parts
Ford Fusion Camshaft, Driver Side Part Number: 9T4Z-6250-B
Product Specifications
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Intake Camshaft Part Number: AU7Z-6250-ARM
Product Specifications
- Other Name: Remanufactured Camshaft; Camshaft
- Replaces: 6E5Z-6250-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Exhaust Camshaft Part Number: AU7Z-6250-BRM
Product Specifications
- Other Name: Remanufactured Camshaft; Camshaft
- Replaces: 3M4Z-6250-CELH, 3M4Z-6250-CAALH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Intake Camshaft Part Number: AU7Z-6250-CRM
Product Specifications
- Other Name: Remanufactured Camshaft; Camshaft
- Replaces: 6E5Z-6250-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Exhaust Camshaft Part Number: AU7Z-6250-DRM
Product Specifications
- Other Name: Remanufactured Camshaft; Camshaft
- Replaces: 3M4Z-6250-CAARH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Intake Camshaft Part Number: 9E5Z-6250-A
Product Specifications
- Other Name: Camshaft
- Manufacturer Note: Intake
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)

| Page 1 of 2 |Next >

1-20 of 30 Results

Ford Fusion Camshaft

OEM Camshaft boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Camshaft with long life and a perfect fit. Come to our website and find genuine Ford Fusion parts. We keep a wide inventory of OEM Fusion parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Camshaft: the device in Ford Fusion cars regulating the operation of the intake and exhaust valves, allowing the mixture to enter the cylinder as well as expelling the exhaust gases. Traditionally, made of cast iron or steel with different mechanisms such as Over Head Valve (OHV), Single Over Head Cam (SOHC) and Double Over Head Cam (DOHC). All of them affect the performance of an engine in varying degrees, with DOHC setups being capable of allowing independent control of intake and exhaust valves which increases efficiency. The camshaft is connected to the crankshaft so that each component will be in harmony and properly synchronized for the correct working of the valves. As illustrated, performance camshafts can be tuned for certain objective, which means that, while enhancing the lift and prolongating the duration contributes to the enhanced flow rate and power of the engine. Other key features including Lobe Separation Angle (LSA) has an impact on torque as well as idle on Ford Fusion vehicles for refined performance. Altogether, camshaft makes the tasks of the engines improved and optimized to achieve the supreme capabilities of the vehicle.

Ford Fusion Camshaft Parts and Q&A

Exhaust Camshaft
CT1Z-6250-B
Q: How to service and repair the right-hand camshaft on Ford Fusion?
A:
You must start with timing drive component removal when you need to work on the right-hand camshaft. The technicians should verify that camshafts maintain neutral position before extracting bearing caps and need to stop the camshaft from rotating during removal of variable camshaft timing (VCT) actuator. A 3/8-inch ratchet extension in the D-slot on the rear intake camshaft should be used to hold it in position so the VCT actuator bolt can be removed along with the actuator. The cylinder head camshaft bearing caps receive numbered identification for organized installation; when numbers are obscured the caps should be marked prior to disassembly. You should begin your removal operation by taking out the thrust caps (5R and 1R) since they need to be detached first to prevent damaging the components. Start by equally loosening bolts per their specified sequence before extracting the thrust caps and proceeding to the remaining camshaft bearing caps and finally extracting the camshafts from the cylinder head. The VCT actuator ought to be positioned onto the intake camshaft prior to bolt installation which should begin with just sufficient finger pressure. The operation will start by applying clean engine oil to the camshafts before carefully putting them onto the cylinder head while maintaining their neutral position. Engine damage prevention occurs when camshaft caps stay in their original positions while the installation of thrust caps must wait until all bearing caps are present to prevent damage. Apply lubrication to the camshaft bearing caps surface then place them loosely onto the engine parts before adding the loosely installed thrust caps. Install the camshaft bearing cap bolts at 10 Nm (89 inch lbs.) while following the specified installation order. When tightening the VCT actuator bolt maintain the camshaft in neutral position by using a ratchet and extension as a fixture to secure it. To complete the installation process fasten the VCT actuator bolt to 40 Nm (30 ft. lbs.) while applying an additional 90 degrees rotation and reinstall all timing drive components.