How to Service the Seat Backrest Thermo-Electric Device (TED) Seat Heater on Ford Fusion?

The first step for servicing the seat backrest Thermo-Electric Device (TED) involves removing the front seat backrest. Start by removing the two head restraint guide sleeves followed by disconnecting the side air bag bolt cover from its position. During reassembly of the seat backrest note how the side air bag module locator hook fits in its bracket and detach the bolt to lift the side air bag module before tightening the bolt to 10 Nm (89 lb-in). Free the electrical connection of the side air bag module by wiggling the locking clip along with the tab release. The pin-type retainers need removal followed by careful handling of the hook-and-loop strip when removing the trim cover from the backrest foam pad. Users should first remove the lower J-clips to view the rear upper hog rings before stripping out all components containing the trim cover. First inspect the climate-controlled seat backrest manifold for any signs of damage and replace it if needed to align it properly with both foam pad and TED assembly to prevent airflow blockage. Detach the upper support spring foam pad by removing the hog rings from its support spring. Disconnect the TED assembly electrical connector then remove the wiring harness retainers and detach the TED exhaust duct by cutting and removing the tie strap until separation occurs. Detach the backrest upper support spring from the frame before removing it with the TED attached. To detach the TED filter from the TED you should note where the filter sits on the support spring. Cover all TED ports with protective materials as you remove the bracket along with its three rivets since this will prevent contamination. A seat side air bag module replacement is necessary in cases where the cover suffers damage or exposes air bag materials since no repair methods are authorized for these components. A thorough inspection must determine the presence of damage or foreign material on the mounting surfaces and seat side air bag module before installation while using new replacement parts for damaged components and removing all foreign material. The process requires selection of an appropriate backrest trim cover for seats with a side air bag module installed. After performing installation reverse the procedure by which you removed parts.

OEM Ford Fusion Seat Heater

Seat Warmer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Seat Heaters found

View related parts
Ford Fusion Seat Cushion Heater Part Number: DP5Z-14D696-C
$39.64 MSRP: $54.84
You Save: $15.20 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Element Assembly - Heating; Seat Heater; Element
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Fusion | S, SE, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Seat Back Heater, Front Part Number: 6E5Z-14D696-BA
$74.37 MSRP: $102.89
You Save: $28.52 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Element Assembly - Heating; Seat Heater Pad, Front, Front Left; Element; Seat Heater
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2008 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Seat Heater, Front Part Number: AE5Z-14D696-D
$148.85 MSRP: $216.67
You Save: $67.82 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Element Assembly - Heating; Seat Heater Pad, Front Left, Front Right; Element
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Seat Back Heater Part Number: DP5Z-14D696-B
$31.62 MSRP: $43.74
You Save: $12.12 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Element; Seat Heater
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Fusion | S, SE, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Seat Back Heater Part Number: DP5Z-14D696-G
$37.28 MSRP: $53.33
You Save: $16.05 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Element; Seat Heater
- Replaces: DP5Z-14D696-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Fusion | S, SE, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Seat Cushion Heater Part Number: DP5Z-14D696-F
$48.93 MSRP: $70.00
You Save: $21.07 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Element Assembly - Heating; Seat Heater; Element
- Replaces: DP5Z-14D696-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Fusion | S, SE, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Seat Back Heater, Front Passenger Side Part Number: 9E5Z-14D696-A
$43.37 MSRP: $60.00
You Save: $16.63 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Element; Seat Heater Pad, Front, Front Right; Seat Heater
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2010 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Seat Back Heater, Front Driver Side Part Number: AE5Z-14D696-C
Product Specifications
- Other Name: Element; Seat Heater Pad, Front Left; Seat Heater
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Seat Back Heater, Front Passenger Side Part Number: AE5Z-14D696-B
Product Specifications
- Other Name: Element; Seat Heater Pad, Front Right; Seat Heater
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Seat Back Heater, Front Driver Side Part Number: AE5Z-14D696-A
Product Specifications
- Other Name: Element; Seat Heater Pad, Front Left; Seat Heater
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Seat Heater, Front Part Number: 6E5Z-14D696-AA
Product Specifications
- Other Name: Element Assembly - Heating; Seat Heater Pad, Front, Front Left, Front Right; Element
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Seat Back Heater, Front Driver Side Part Number: 9E5Z-14D696-B
Product Specifications
- Other Name: Element; Seat Heater Pad, Front Left; Seat Heater
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Seat Back Heater, Front Passenger Side Part Number: 7E5Z-14D696-A
Product Specifications
- Other Name: Element; Seat Heater Pad, Front Right; Seat Heater
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

Ford Fusion Seat Heater

OEM Seat Heater boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Seat Heater with long life and a perfect fit. Come to our website and find genuine Ford Fusion parts. We keep a wide inventory of OEM Fusion parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Fuses are among the most attractive options in the Ford Fusion types, which customers praise for its operation and providing a warm seat for the passengers in winter. Integrating the seat heat pad into the seats' fabric, the Seat Heater establishes the desired heat output and provides the occupants with a comfortable temperature irrespective of the outer conditions. This particular feature is suitable in different Ford Fusion models, which is an added advantage when installing this feature in the car. The Seat Heater does not only consider a more comfortable option but also contributes much in efficiency and safety aspect as warm seat quickly keep the driver's full concentration on roads without any discomfort interruption. The Seat Heater has been considered to be a reliable product due to its steady performance and that is why most of the drivers prefer it. Additional, features such as heat controls can be regulated to fit the use's preferences making the Seat Heater unique in the automobile industry. Since 2005 the Ford Fusion has always been commended for being environmental friendly and also for incorporating the latest technology to the car's production making it a very reliable car. In sum, the Ford Seat Heater for Fusion shows the dedication of Ford to the high-quality production and the customers' comfort, meaning this is a must-have part for those who seek to improve the driving experience in Ford Fusion.

Ford Fusion Seat Heater Parts and Q&A

Seat Back Heater, Front Driver Side
9E5Z-14D696-B
Q: How to Service the Seat Backrest Thermo-Electric Device (TED) Seat Heater on Ford Fusion?
A:
The first step for servicing the seat backrest Thermo-Electric Device (TED) involves removing the front seat backrest. Start by removing the two head restraint guide sleeves followed by disconnecting the side Air Bag bolt cover from its position. During reassembly of the seat backrest note how the side air bag module locator hook fits in its bracket and detach the bolt to lift the side air bag module before tightening the bolt to 10 Nm (89 lb-in). Free the electrical connection of the side air bag module by wiggling the locking clip along with the tab release. The pin-type retainers need removal followed by careful handling of the hook-and-loop strip when removing the trim cover from the backrest foam pad. Users should first remove the lower J-clips to view the rear upper hog rings before stripping out all components containing the trim cover. First inspect the climate-controlled seat backrest manifold for any signs of damage and replace it if needed to align it properly with both foam pad and TED assembly to prevent airflow blockage. Detach the upper support spring foam pad by removing the hog rings from its support spring. Disconnect the TED assembly electrical connector then remove the wiring harness retainers and detach the TED exhaust duct by cutting and removing the tie strap until separation occurs. Detach the backrest upper support spring from the frame before removing it with the TED attached. To detach the TED filter from the TED you should note where the filter sits on the support spring. Cover all TED ports with protective materials as you remove the bracket along with its three rivets since this will prevent contamination. A seat side air bag module replacement is necessary in cases where the cover suffers damage or exposes air bag materials since no repair methods are authorized for these components. A thorough inspection must determine the presence of damage or foreign material on the mounting surfaces and seat side air bag module before installation while using new replacement parts for damaged components and removing all foreign material. The process requires selection of an appropriate backrest trim cover for seats with a side air bag module installed. After performing installation reverse the procedure by which you removed parts.