How to Properly Service and Repair a Sway Bar Kit on Ford Mustang?

Service work on sway bar links should only start when the vehicle sits at neutral position on a hoist. A holding feature should be used to maintain stability of the studs during sway bar link nut installation and removal because it helps keep the boot seal from twisting as the nuts get tightened. The installation of the sway bar link demands that you discard both lower nuts then tighten them to 115 Nm (85 ft. lbs). Proceed by disconnecting the sway bar links from the unit then remove the four sway bar bracket nuts followed by the sway bar brackets and bar before reinstalling it with 70 Nm (52 ft. lbs) torque. The procedure ends with reversing the steps of removal. Before final installation you can remove the sway bar bushings if needed. When fixing components it is essential to use new replacement parts with the same part number or equivalent. Inferior replacement parts will create notable service problems while following specified torque standards prevents component movement during reinstallation.

How to Properly Install a Sway Bar Kit on Ford Mustang?

Start sway bar link and kit service operations by placing the vehicle in neutral position on a hoist. The sway bar link bolts and clip nuts should be discarded before installation where the new bolts get tightened to 115 Nm (85 ft. lbs). The installer should first remove the sway bar bracket nuts and studs and brackets along with the sway bar before discarding the sway nuts and studs and tightening new ones to 70 Nm (52 ft. lbs). The professional should take out bushings and links from the sway bar if needed. The LH side tag on the sway bar must be placed properly to the left side of the vehicle during replacement installation. The installation of a new sway bar requires the use of the proper bar for convertible or coupe vehicles while maintaining the same tag color between the bar and the original component. The absence of a tag on an original sway bar will be compensated by examining link coatings for color identification where a black link calls for tag "A" yellow while white links require tag "B" in green and blue/gray links need tag "C" in orange. The final step for the installation will follow the steps of reinstallation.

OEM Ford Mustang Sway Bar Kit

Stabilizer Sway Bar Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

39 Sway Bar Kits found

View related parts
Ford Mustang Stabilizer Bar, Front Part Number: BR3Z-5482-F
$297.88 MSRP: $412.08
You Save: $114.20 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Replaces: BR3Z-5482-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2013 Ford Mustang | Base, GT, Shelby GT500 | 6 Cyl 3.7 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 5.8 L GAS
View related parts
Ford Mustang Stabilizer Bar, Rear Part Number: F6ZZ-5A772-BA
$380.80 MSRP: $526.81
You Save: $146.01 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar - Rear Stabilizer; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-2004 Ford Mustang | GT, GT Bullitt, GTS | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Mustang Stabilizer Bar, Front Part Number: 6R3Z-5482-B
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Replaces: 4R3Z-5482-BA, 7R3Z-5482-B, AR3Z-5482-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2009 Ford Mustang | Bullitt, GT, Shelby GT, Shelby GT500, Shelby GT500KR | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Mustang Stabilizer Bar, Front Part Number: 7R3Z-5482-A
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Replaces: 7R3Z-5482-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Ford Mustang | Shelby GT500, Shelby GT500KR | 8 Cyl 5.4 L GAS
View related parts
Ford Mustang Stabilizer Bar, Front Part Number: BR3Z-5482-A
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Manufacturer Note: Service Part May Differ From Production
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Mustang | Base, Boss 302, GT, Shelby GT500 | 6 Cyl 3.7 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 5.8 L GAS
View related parts
Ford Mustang Stabilizer Bar Part Number: XR3Z-5482-EA
Product Specifications
- Other Name: Bar - Stabilizer; Sway Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2004 Ford Mustang | GT | 8 Cyl 4.6 L GAS
View related parts
Ford Mustang Stabilizer Bar Part Number: 6R3Z-5A772-A
Product Specifications
- Other Name: Bar - Stabilizer; Suspension Stabilizer Bar, Rear; Sway Bar
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2010 Ford Mustang | Base, GT, Shelby GT, Shelby GT500 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Mustang Stabilizer Bar, Rear Part Number: BR3Z-5A772-C
Product Specifications
- Other Name: Bar - Stabilizer; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011 Ford Mustang | Base, GT, Shelby GT500 | 6 Cyl 3.7 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Mustang Stabilizer Bar, Front Part Number: 2R3Z-5482-AA
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Mustang | GT, Mach 1, SVT Cobra, SVT Cobra 10th Anniversary | 8 Cyl 4.6 L GAS
View related parts
Ford Mustang Stabilizer Bar, Rear Part Number: 3R3Z-5A772-AA
Product Specifications
- Other Name: Bar - Rear Stabilizer; Suspension Stabilizer Bar, Rear; Sway Bar
- Manufacturer Note: 26MM
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Mustang | Base, GT, Mach 1, SVT Cobra, SVT Cobra 10th Anniversary | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Mustang Stabilizer Bar, Front Part Number: 6R3Z-5482-A
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010, 2005-2006 Ford Mustang | Base, GT, Shelby GT500 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Mustang Stabilizer Bar, Rear Part Number: 6R3Z-5A772-B
Product Specifications
- Other Name: Bar - Stabilizer; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2009 Ford Mustang | Base, GT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Mustang Stabilizer Bar, Front Part Number: 7R3Z-5482-E
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Ford Mustang | Base | 6 Cyl 4.0 L GAS
View related parts
Ford Mustang Stabilizer Bar, Rear Part Number: 7R3Z-5A772-A
Product Specifications
- Other Name: Bar - Stabilizer; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Mustang | Base, Bullitt, GT, Shelby GT, Shelby GT500, Shelby GT500KR | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Mustang Stabilizer Bar, Front Part Number: AR3Z-5482-A
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010 Ford Mustang | Base, GT, Shelby GT500 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Mustang Stabilizer Bar, Rear Part Number: BR3Z-5A772-A
Product Specifications
- Other Name: Bar - Stabilizer; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011 Ford Mustang | Base, GT, Shelby GT500 | 6 Cyl 3.7 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Mustang Stabilizer Bar, Front Part Number: DR3Z-5482-D
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Replaces: DR3Z-5482-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Mustang | Shelby GT500 | 8 Cyl 5.8 L GAS
View related parts
Ford Mustang Stabilizer Bar, Rear Part Number: F4ZZ-5A772-C
Product Specifications
- Other Name: Bar - Rear Stabilizer; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-2004 Ford Mustang | Base, GT Bullitt | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Mustang Stabilizer Bar, Rear Part Number: F7ZZ-5A772-AA
Product Specifications
- Other Name: Bar - Rear Stabilizer; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1998 Ford Mustang | SVT Cobra | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Mustang Stabilizer Bar, Front Part Number: XR3Z5482CC
Product Specifications
- Other Name: Bar Assembly - Roll; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2004 Ford Mustang | GT, GT Bullitt, SVT Cobra | 8 Cyl 4.6 L GAS

| Page 1 of 2 |Next >

1-20 of 39 Results

Ford Mustang Sway Bar Kit

OEM Sway Bar Kit boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Sway Bar Kit with long life and a perfect fit. Come to our website and find genuine Ford Mustang parts. We keep a wide inventory of OEM Mustang parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Sway Bar Kit for Ford Mustang vehicles simply improves handling by diminishing body roll in cornering and when the car is on rough roads. Designed to link the opposite ends of the suspension system the Sway Bar Kit makes use of torsion springs to enhance the roll stiffness although it does not affect the vertical spring rate. This design is useful in maintaining a good posture while riding as much sideward leaning as possible is avoided, and more road traction realized. In Mustang models, several categories of Sway Bar Kits have been used over years such as adjustable and active anti-roll bars. These new systems are characterized by variable stiffness that makes it possible to adjust the vehicle's handling and stability. Despite being strong enough to reduce body lean, older model sway bars are most times inadvertently known to pass on impacts between wheels making travelling on bumpy grounds uncomfortable. In general, the Ford Mustang Sway Bar Kit is used in the tuning of the handling characteristic of the vehicle.

Ford Mustang Sway Bar Kit Parts and Q&A

Stabilizer Bar
6R3Z-5A772-A
Q: How to Properly Service and Repair a Sway Bar Kit on Ford Mustang?
A:
Service work on Sway Bar Links should only start when the vehicle sits at neutral position on a hoist. A holding feature should be used to maintain stability of the studs during sway bar link nut installation and removal because it helps keep the boot seal from twisting as the nuts get tightened. The installation of the sway bar link demands that you discard both lower nuts then tighten them to 115 Nm (85 ft. lbs). Proceed by disconnecting the sway bar links from the unit then remove the four sway bar bracket nuts followed by the sway bar brackets and bar before reinstalling it with 70 Nm (52 ft. lbs) torque. The procedure ends with reversing the steps of removal. Before final installation you can remove the Sway Bar Bushings if needed. When fixing components it is essential to use new replacement parts with the same part number or equivalent. Inferior replacement parts will create notable service problems while following specified torque standards prevents component movement during reinstallation.
Stabilizer Bar, Front
6R3Z-5482-B
Q: How to Properly Install a Sway Bar Kit on Ford Mustang?
A:
Start Sway Bar Link and kit service operations by placing the vehicle in neutral position on a hoist. The sway bar link bolts and clip nuts should be discarded before installation where the new bolts get tightened to 115 Nm (85 ft. lbs). The installer should first remove the sway bar bracket nuts and studs and brackets along with the sway bar before discarding the sway nuts and studs and tightening new ones to 70 Nm (52 ft. lbs). The professional should take out bushings and links from the sway bar if needed. The LH side tag on the sway bar must be placed properly to the left side of the vehicle during replacement installation. The installation of a new sway bar requires the use of the proper bar for convertible or coupe vehicles while maintaining the same tag color between the bar and the original component. The absence of a tag on an original sway bar will be compensated by examining link coatings for color identification where a black link calls for tag "A" yellow while white links require tag "B" in green and blue/gray links need tag "C" in orange. The final step for the installation will follow the steps of reinstallation.