How to remove and replace the front bumper cover on Ford Taurus?

The procedure for front bumper cover replacement on Taurus, Sable and Taurus X vehicles requires hoisting the vehicle into neutral position. The first step requires scrivets' removal from both front bumper cover locations and subsequent front bumper bolts' extraction followed by a 6 Nm (53 lb-in) bolt torque when reinstalling all parts. The next step involves removing the six front bumper cover wheel house screws while installation requires their screws to be tight at 2 Nm (18 lb-in). Remove the electrical connectors of the fog lights together with any existing front side marker lamps. One must unclip the bumper cover from the fender while gently pulling its upper rear end to finish the complete cover removal. Check the bumper cover mounting reinforcements for damage after removal then apply new parts if necessary. The process ends by executing steps that were used to remove the components.

How to service the rear bumper cover on Ford Taurus?

Service of the rear bumper cover begins with placing the vehicle into neutral gear on a hoist. First remove the fuel filler overflow tube before removing the six pin-type retainers attached to the rear bumper cover. Before reaching the rear bumper cover-to-body nuts begin by taking out four screws then setting aside both left-hand splash shield and right-hand splash shield. The installation process requires torqueing these nuts to 9 Nm which corresponds to 80 lb-in. Remove firstly the five pin-type retainers then the two nuts and finally three pin-type retainers and the scuff plate and place left-hand and right-hand luggage compartment trim panels to the side. You should extract the six rear bumper cover-to-body nuts and ultimately remove the rear bumper cover after tightening all the nuts to 9 Nm (80 lb-in) as part of the reinstallation process. The procedure will be finished by following the removal procedure in reverse order.

OEM Ford Taurus Bumper Cover

Bumper Shell

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Bumper Covers found

View related parts
Ford Taurus Bumper Cover, Rear Part Number: DG1Z-17K835-AAPTM
$479.41 MSRP: $703.98
You Save: $224.57 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover, Rear Part Number: DG1Z-17K835-GAPTM
$680.38 MSRP: $809.98
You Save: $129.60 (16%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover, Rear Part Number: 8G1Z-17K835-AAPTM
$219.05 MSRP: $298.09
You Save: $79.04 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover, Front Part Number: 8G1Z-17D957-AAPTM
$155.37 MSRP: $239.77
You Save: $84.40 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover, Rear Part Number: AG1Z-17K835-MAPTM
$564.71 MSRP: $836.60
You Save: $271.89 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Replaces: AG1Z-17K835-BAPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | Limited, Police, SE, SEL, SHO | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover, Front Part Number: DG1Z-17D957-HAPTM
$418.76 MSRP: $614.92
You Save: $196.16 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Manufacturer Note: Prime, Paint To Match - Reference TSB 03-10-1
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover, Rear Part Number: AG1Z-17K835-LAPTM
$488.22 MSRP: $716.92
You Save: $228.70 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Replaces: AG1Z-17K835-APTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | Limited, Police, SE, SEL, SHO | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover, Rear Part Number: 2F1Z-17K835-CA
$100.60 MSRP: $136.89
You Save: $36.29 (27%)
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Replaces: YF1Z-17K835-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2003 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 3.0L V6, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Bumper Cover, Rear Part Number: 4F1Z-17K835-CA
$155.53 MSRP: $211.64
You Save: $56.11 (27%)
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Taurus | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Bumper Cover, Front Part Number: AG1Z-17D957-AAPTM
$283.25 MSRP: $330.90
You Save: $47.65 (15%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | Limited, SE, SEL, SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover, Front Part Number: DG1Z-17D957-AAPTM
$662.55 MSRP: $794.01
You Save: $131.46 (17%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Manufacturer Note: Prime, Paint To Match - Reference TSB 03-10-1
- Position: Front
- Replaces: DG1Z-17D957-BAPTM, DG1Z-17D957-CAPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover Part Number: F3DZ17D957A
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Ford Taurus | SHO | 6 Cyl 3.0 L GAS, 6 Cyl 3.2 L GAS
View related parts
Ford Taurus Bumper Cover, Rear Part Number: 8G1Z-17K835-CAPTM
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover, Rear Part Number: AG1Z-17K835-NAPTM
$556.64 MSRP: $824.65
You Save: $268.01 (33%)
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Replaces: AG1Z-17K835-CAPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Taurus | Limited, Police, SE, SEL, SHO | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Bumper Cover Part Number: F8DZ-17K835-AA
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Ford Taurus | GL, LX, SE, SE Comfort | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Bumper Cover Part Number: F8DZ-17D957-BA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match, exc. SHO
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-1999 Ford Taurus | LX, SE, SE Comfort | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Bumper Cover Part Number: F6DZ-17K835-A
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match , exc. SHO
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Ford Taurus | G, GL, LX, SE, SE Comfort | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Bumper Cover, Front Part Number: 4F1Z-17D957-DA
Product Specifications
- Other Name: Bumper - Cover
- Manufacturer Note: Paint to match, No license plate brkt used.
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Taurus | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Bumper Cover, Rear Part Number: 2F1Z-17K835-DA
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Replaces: YF1Z-17K835-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Ford Taurus | SE, SE Comfort, SEL | 3.0L V6, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Bumper Cover, Front Part Number: 2F1Z-17D957-BA
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Manufacturer Note: Paint to match, It may also be necessary to order any color 2F1Z 8200 grille & paint to match
- Position: Front
- Replaces: YF1Z-17D957-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2003 Ford Taurus | LX, SE, SE Comfort, SEL, SES, SVG | 3.0L V6, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

Ford Taurus Bumper Cover

OEM Bumper Cover boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Bumper Cover with long life and a perfect fit. Come to our website and find genuine Ford Taurus parts. We keep a wide inventory of OEM Taurus parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Ford Taurus Bumper Cover is a soft exterior panel that hides the rigid bumper, enhancing appearance and safety as well. Attached at the front or rear of the vehicle, the Bumper Cover helps reduce shock from minor collisions and decreases drag to boost speed and fuel economy. The parking aid sensor, fog lights, the license plate, and the channel to cool the radiator and other heat exchangers may be in the Bumper Cover opening. Spaces left vacant by equipment are filled with decorative inserts or bezels to maintain the surface. A small cap can also be applied to cover the tow eye anchor point in the Bumper Cover. This ensures exterior continuity until recovery hardware is needed. Offered as a single piece, as a multi-piece set or kit, it easily installs as a direct-fit replacement on Ford models without altering the body lines. Regardless of whether the part is fitted to a sedan, wagon, hatchback or convertible version of the Taurus, the Bumper Cover is built to factory specifications so each Taurus retains its original Ford appearance and consistent Taurus styling while restoring protection.

Ford Taurus Bumper Cover Parts and Q&A

Bumper Cover, Front
8G1Z-17D957-AAPTM
Q: How to remove and replace the front bumper cover on Ford Taurus?
A:
The procedure for front bumper cover replacement on Taurus, Sable and Taurus X vehicles requires hoisting the vehicle into neutral position. The first step requires scrivets' removal from both front bumper cover locations and subsequent front bumper bolts' extraction followed by a 6 Nm (53 lb-in) bolt torque when reinstalling all parts. The next step involves removing the six front bumper cover wheel house screws while installation requires their screws to be tight at 2 Nm (18 lb-in). Remove the electrical connectors of the fog lights together with any existing front side marker lamps. One must unclip the bumper cover from the fender while gently pulling its upper rear end to finish the complete cover removal. Check the bumper cover mounting reinforcements for damage after removal then apply new parts if necessary. The process ends by executing steps that were used to remove the components.
Bumper Cover, Rear
4F1Z-17K835-CA
Q: How to service the rear bumper cover on Ford Taurus?
A:
Service of the rear bumper cover begins with placing the vehicle into neutral gear on a hoist. First remove the fuel filler overflow tube before removing the six pin-type retainers attached to the rear bumper cover. Before reaching the rear bumper cover-to-body nuts begin by taking out four screws then setting aside both left-hand splash shield and right-hand splash shield. The installation process requires torqueing these nuts to 9 Nm which corresponds to 80 lb-in. Remove firstly the five pin-type retainers then the two nuts and finally three pin-type retainers and the scuff plate and place left-hand and right-hand luggage compartment trim panels to the side. You should extract the six rear bumper cover-to-body nuts and ultimately remove the rear bumper cover after tightening all the nuts to 9 Nm (80 lb-in) as part of the reinstallation process. The procedure will be finished by following the removal procedure in reverse order.