How to remove and replace the front bumper cover on Lincoln MKS?

A hoist must position the vehicle in neutral to allow effective front bumper cover replacement. The first step involves removing 2 front bumper cover scrivets while tightening their installation to 6 Nm (53 lb-in) and discarding 4 front bumper cover bolts with the same torque value. Your first step should be to remove the 6 front bumper cover wheel house screws which exist in sets of three per side and the 2 screws that reside in the front upper wheel well with one screw present on each side. Cuts off the lower inside LH bumper cover fog lamp electrical connector as well as removes the speed control sensor electrical connector when present. Before removing the front bumper cover take out seven lower scrivets from the air deflector along with notating how the upper rear section must pop outward from the fender to separate it out. Check if the bumper cover mounting reinforcements have damage and replace them if needed. Reverse the removal steps when performing installation of this component.

How to remove and replace the rear bumper cover on Lincoln MKS?

The process of bumper cover replacement starts with placing the vehicle into neutral gear and mounting it on a hoist. The first step includes lamp removal and disconnecting the electrical connector for the rear bumper cover. Start by unscrewing the six fender splash shield screws which are divided into three on each wheel well. You must separate the rear bumper cover by first removing its two screws that connect to the mounting bracket then disconnecting both pin-type retainers between the bumper cover and the bumper. When unclipping the bumper cover from the mounting reinforcement be careful to avoid damage by pulling the forward upper portion of the cover outward. The removal steps for the rear bumper cover must be completed in reverse order after inspection of bumper cover mounting reinforcements for replacement as needed.

OEM Lincoln MKS Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Bumpers found

View related parts
Lincoln MKS Impact Bar, Front Part Number: DG1Z-17757-A
$350.48 MSRP: $411.72
You Save: $61.24 (15%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Impact Bar, Front
- Position: Front
- Replaces: DG1Z-17757-B, 8A8Z-17757-A, AA8Z-17757-A, DG1Z-17757-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2016 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Bumper Cover, Front Part Number: DA5Z-17D957-BAPTM
$389.75 MSRP: $611.08
You Save: $221.33 (37%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Bumper Cover, Front Part Number: DA5Z-17D957-ABPTM
$565.95 MSRP: $705.75
You Save: $139.80 (20%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Bumper Cover, Front Part Number: 8A5Z-17D957-AAPTM
$202.93 MSRP: $295.38
You Save: $92.45 (32%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front
- Manufacturer Note: Prime, Paint To Match - Reference TSB 03-10-1
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Bumper Cover, Rear Part Number: DA5Z-17K835-APTM
$630.72 MSRP: $934.40
You Save: $303.68 (33%)
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Replaces: DA5Z-17K835-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Impact Bar, Rear Part Number: AG1Z-17906-A
$249.86 MSRP: $366.90
You Save: $117.04 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Impact Bar, Rear
- Manufacturer Note: To Be Used For Servicing All Prior Models Along With Isolator AA5Z-17E855-A
- Position: Rear
- Replaces: 8A5Z-17906-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Lincoln MKS | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Bumper Cover Part Number: AA5Z-17D957-SAPTM
$644.13 MSRP: $809.92
You Save: $165.79 (21%)
ADD TO CART
Product Specifications
- Other Name: Cover
- Manufacturer Note: Prime, Paint To Match - Reference TSB 03-10-1
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Bumper Cover Part Number: 8A5Z-17D957-GAPTM
$859.30
ADD TO CART
Product Specifications
- Other Name: Cover
- Manufacturer Note: Prime, Paint To Match - Reference TSB 03-10-1
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Impact Bar, Rear Part Number: BG1Z-17906-A
$160.20 MSRP: $233.18
You Save: $72.98 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Impact Bar, Rear
- Position: Rear
- Replaces: AG1Z-17787-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2016 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Deflector, Front Lower Part Number: DA5Z-17D957-AA
$215.88 MSRP: $317.00
You Save: $101.12 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Valance Panel, Front
- Position: Front Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Bumper Cover Part Number: 8A5Z-17K835-GAPTM
$513.51 MSRP: $754.05
You Save: $240.54 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS

Lincoln MKS Bumper

OEM Bumper boasts unmatched quality. Each part goes through full quality checks. They adhere to Lincoln's official factory standards. These steps remove flaws and inconsistencies. So you can get Bumper with long life and a perfect fit. Come to our website and find genuine Lincoln MKS parts. We keep a wide inventory of OEM MKS parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

As an essential element of the Lincoln MKS Bumper demonstrates both the trustworthiness and performance characteristics associated with Lincoln vehicles. This bumper system in the Lincoln MKS Bumper uses impact energy absorption to shield the vehicle's body structure together with key safety systems which leads to increased efficiency and safeguarding against harm. Vehicle owners can protect their 2008-2016 MKS luxury sedans by using this bumper which supports different versions of the model lineup. Energy-absorbing materials enclosed by a sophisticated plastic shell distinguish the modern Lincoln MKS Bumper from its predecessors because they dramatically enhance its performance capabilities. The durable design philosophy of the Lincoln MKS Bumper is represented by its construction blend of aluminum for weight reduction and corrosion-resistant stainless steel and tough carbon steel materials. The car Bumper sets itself apart in automobile markets by showing a perfect combination with the vehicle's design principles while demonstrating the automaker's dedication to luxury through innovative approaches. Through expert engineering and modern materials the car component raises the appearance of the model sedan while simultaneously safeguarding its safety performance and operational efficiency. The car part demonstrates outstanding reliability and excellence which characterizes the brand legacy.

Lincoln MKS Bumper Parts and Q&A

Impact Bar, Front
DG1Z-17757-A
Q: How to remove and replace the front bumper cover on Lincoln MKS?
A:
A hoist must position the vehicle in neutral to allow effective front bumper cover replacement. The first step involves removing 2 front bumper cover scrivets while tightening their installation to 6 Nm (53 lb-in) and discarding 4 front bumper cover bolts with the same torque value. Your first step should be to remove the 6 front bumper cover wheel house screws which exist in sets of three per side and the 2 screws that reside in the front upper wheel well with one screw present on each side. Cuts off the lower inside LH bumper cover fog lamp electrical connector as well as removes the speed control sensor electrical connector when present. Before removing the front bumper cover take out seven lower scrivets from the air deflector along with notating how the upper rear section must pop outward from the fender to separate it out. Check if the bumper cover mounting reinforcements have damage and replace them if needed. Reverse the removal steps when performing installation of this component.
Impact Bar, Rear
AG1Z-17906-A
Q: How to remove and replace the rear bumper cover on Lincoln MKS?
A:
The process of bumper cover replacement starts with placing the vehicle into neutral gear and mounting it on a hoist. The first step includes lamp removal and disconnecting the electrical connector for the rear bumper cover. Start by unscrewing the six fender splash shield screws which are divided into three on each wheel well. You must separate the rear bumper cover by first removing its two screws that connect to the mounting bracket then disconnecting both pin-type retainers between the bumper cover and the bumper. When unclipping the bumper cover from the mounting reinforcement be careful to avoid damage by pulling the forward upper portion of the cover outward. The removal steps for the rear bumper cover must be completed in reverse order after inspection of bumper cover mounting reinforcements for replacement as needed.