How to service the right-hand catalytic converter on all on Lincoln MKX?

Service of the right-hand catalytic converter for all vehicles requires separate attention to the catalytic converter heat shield if needed. The service requires fresh fasteners and gaskets along with clean flange faces that must be ready before putting in the new gasket for sealing purposes. Position the vehicle with neutral gear on a hoist before you eliminate the catalyst monitor sensor from its position. Next, remove the exhaust Y-pipe. Index-mark all-wheel drive vehicle driveshafts because installation will require removal of four U-joint flange bolts to separate the front driveshaft before fixing it with mechanic's wire. Reinstall the driveshaft bolts to reach torque values of 70 Nm (52 lb-ft). The intermediate shaft requires removal before you tighten the two bolts securing the catalytic converter support brackets to the engine block to 40 Nm (30 lb-ft). Replacing the power steering gear heat shield requires removal of its two bolts which you should fasten to 15 Nm (133 lb-in) torque settings during installation. To reinstall the front-wheel drive components you should tighten the catalytic converter support bracket-to-engine block bolt and nut to 40 Nm (30 lb-ft). Start by removing two nuts along with the roll restrictor shield before uninstalling the roll restrictor bolt to rotate the engine forward while torquing the bolt to 90 Nm (66 lb-ft) for reinstallation. The installation process requires tightening the two bracket-to-right-hand catalytic converter bolts to 20 Nm (177 lb-in). After removing the four nuts your work includes discarding both the nuts and gasket from the right-hand catalytic converter. Prior to installing the new catalytic converter you must use new gaskets and nuts and studs with the nuts needing to be tightened to 40 Nm (30 lb-ft). You should reverse the removal process to finish the work.

How to service the LH catalytic converter on Lincoln MKX?

The service of LH catalytic converter requires motorists to place their vehicle in neutral position while mounting the vehicle on a hoist. The service of the catalytic converter heat shield operates independently from the other components. You must use fresh fasteners and gaskets together with thorough cleaning of flange surfaces before adding the new gasket to create a sound seal. Begin the service work by separating the electrical connector of the catalyst monitor sensor and then pull out the exhaust Y-pipe. Relocate the two bolts that anchor the catalytic converter support bracket at the transmission but tighten them to 48 Nm (35 ft. lbs) before reinstalling. You must separate the LH catalytic converter through removal of four securing nuts which will be discarded along with the gasket. The procedure for new catalytic converter installation requires fresh nuts and a gasket along with 40 Nm (30 ft. lbs) torque settings before performing the reverse procedure to achieve completion.

OEM Lincoln MKX Catalytic Converter

Cat. Converter

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Catalytic Converters found

View related parts
Lincoln MKX Exhaust Manifold, Driver Side Part Number: BT4Z-5G232-C
$745.50 MSRP: $940.00
You Save: $194.50 (21%)
ADD TO CART
Product Specifications
- Other Name: Exhaust Manifold And Catalyst; Catalytic Converter with Integrated Exhaust Manifold, Left; Manifold Converter; Manifold W/Converter; Exhaust Manifold And Catalyst Assembly; Catalytic Converter
- Position: Driver Side
- Replaces: BT4Z-5G232-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2015 Lincoln MKX | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Catalytic Converter, Rear Passenger Side Part Number: BT4Z-5E212-C
$695.63 MSRP: $870.00
You Save: $174.37 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Center, Rear
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2015 Lincoln MKX | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Catalytic Converter, Front Driver Side Part Number: 7T4Z-5E213-A
$777.00 MSRP: $1050.00
You Save: $273.00 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left, Right
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Catalytic Converter, Passenger Side Part Number: 7T4Z-5E212-A
$894.75 MSRP: $1122.86
You Save: $228.11 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left, Right
- Manufacturer Note: Rear
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Catalytic Converter, Front Driver Side Part Number: F2GZ-5G232-C
$1501.50 MSRP: $1900.00
You Save: $398.50 (21%)
ADD TO CART
Product Specifications
- Other Name: Exhaust Manifold And Catalyst; Catalytic Converter with Integrated Exhaust Manifold, Left; Exhaust Manifold; Manifold W/Converter; Exhaust Manifold And Catalyst Assembly
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Catalytic Converter, Passenger Side Part Number: F2GZ-5G232-B
$1239.00 MSRP: $1678.57
You Save: $439.57 (27%)
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter with Integrated Exhaust Manifold, Right; Exhaust Manifold; Manifold W/Converter
- Manufacturer Note: Rear
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Catalytic Converter, Passenger Side Part Number: F2GZ-5E212-B
$656.48 MSRP: $820.29
You Save: $163.81 (20%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS
View related parts
Lincoln MKX Catalytic Converter, Front Driver Side Part Number: 9T4Z-5E213-B
$485.36 MSRP: $604.29
You Save: $118.93 (20%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Catalytic Converter, Driver Side Part Number: F2GZ-5E213-G
$1006.39 MSRP: $1271.29
You Save: $264.90 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left
- Position: Driver Side
- Replaces: F2GZ-5E213-D, F2GZ-5E213-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS
View related parts
Lincoln MKX Catalytic Converter, Driver Side Part Number: F2GZ-5E213-B
$718.05 MSRP: $905.14
You Save: $187.09 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS
View related parts
Lincoln MKX Catalytic Converter, Passenger Side Part Number: F2GZ-5E212-H
$837.38 MSRP: $1050.00
You Save: $212.62 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Right
- Position: Passenger Side
- Replaces: F2GZ-5E212-D, F2GZ-5E212-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS
View related parts
Lincoln MKX Catalytic Converter, Passenger Side Part Number: F2GZ-5E212-G
$713.63 MSRP: $892.86
You Save: $179.23 (21%)
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Right
- Position: Passenger Side
- Replaces: F2GZ-5E212-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS
View related parts
Lincoln MKX Catalytic Converter, Passenger Side Part Number: 9T4Z-5E212-B
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Right
- Manufacturer Note: Rear
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Catalytic Converter, Front Part Number: 7T4Z-5E213-BC
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Right
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Catalytic Converter Part Number: 7T4Z-5E212-BC
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left
- Manufacturer Note: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Catalytic Converter, Driver Side Part Number: F2GZ-5E213-F
$694.88 MSRP: $875.71
You Save: $180.83 (21%)
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Left
- Position: Driver Side
- Replaces: F2GZ-5E213-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS

Lincoln MKX Catalytic Converter

OEM Catalytic Converter boasts unmatched quality. Each part goes through full quality checks. They adhere to Lincoln's official factory standards. These steps remove flaws and inconsistencies. So you can get Catalytic Converter with long life and a perfect fit. Come to our website and find genuine Lincoln MKX parts. We keep a wide inventory of OEM MKX parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Lincoln MKX Catalytic Converter is a vital part of emissions system that plays a role converting toxic fumes such as CO, HC, Nox to less hazardous items such as water vapor, Carbon dioxide, and nitrogen gas. Usually a honeycomb structure coated with the catalysts such as platinum, palladium and rhodium, the converter now promotes redox reactions to bring this change. Available types include direct fit converters and universal converters wherein the universal converters need pipe cutting and clamping for the conversion to be done while the direct fit converters are easy replace the factory converters. Thanks to the reduction of exhaust backpressure and restriction, the Catalytic Converter contributes to enhanced engine performance as well as to the preservation of the catalyst's efficiency to perform oxidation and reduction processes optimally.

Lincoln MKX Catalytic Converter Parts and Q&A

Catalytic Converter, Passenger Side
7T4Z-5E212-A
Q: How to service the right-hand catalytic converter on all on Lincoln MKX?
A:
Service of the right-hand catalytic converter for all vehicles requires separate attention to the catalytic converter heat shield if needed. The service requires fresh fasteners and gaskets along with clean flange faces that must be ready before putting in the new gasket for sealing purposes. Position the vehicle with neutral gear on a hoist before you eliminate the catalyst monitor sensor from its position. Next, remove the exhaust Y-pipe. Index-mark all-wheel drive vehicle driveshafts because installation will require removal of four U-joint flange bolts to separate the front driveshaft before fixing it with mechanic's wire. Reinstall the driveshaft bolts to reach torque values of 70 Nm (52 lb-ft). The intermediate shaft requires removal before you tighten the two bolts securing the catalytic converter support brackets to the engine block to 40 Nm (30 lb-ft). Replacing the power steering gear heat shield requires removal of its two bolts which you should fasten to 15 Nm (133 lb-in) torque settings during installation. To reinstall the front-wheel drive components you should tighten the catalytic converter support bracket-to-engine block bolt and nut to 40 Nm (30 lb-ft). Start by removing two nuts along with the roll restrictor shield before uninstalling the roll restrictor bolt to rotate the engine forward while torquing the bolt to 90 Nm (66 lb-ft) for reinstallation. The installation process requires tightening the two bracket-to-right-hand catalytic converter bolts to 20 Nm (177 lb-in). After removing the four nuts your work includes discarding both the nuts and gasket from the right-hand catalytic converter. Prior to installing the new catalytic converter you must use new gaskets and nuts and studs with the nuts needing to be tightened to 40 Nm (30 lb-ft). You should reverse the removal process to finish the work.
Catalytic Converter, Front Driver Side
7T4Z-5E213-A
Q: How to service the LH catalytic converter on Lincoln MKX?
A:
The service of LH catalytic converter requires motorists to place their vehicle in neutral position while mounting the vehicle on a hoist. The service of the catalytic converter heat shield operates independently from the other components. You must use fresh fasteners and gaskets together with thorough cleaning of flange surfaces before adding the new gasket to create a sound seal. Begin the service work by separating the electrical connector of the catalyst monitor sensor and then pull out the exhaust Y-pipe. Relocate the two bolts that anchor the catalytic converter support bracket at the transmission but tighten them to 48 Nm (35 ft. lbs) before reinstalling. You must separate the LH catalytic converter through removal of four securing nuts which will be discarded along with the gasket. The procedure for new catalytic converter installation requires fresh nuts and a gasket along with 40 Nm (30 ft. lbs) torque settings before performing the reverse procedure to achieve completion.