How to service and repair the rear brake pads on Mercury Grand Marquis?

Starting the process of repairing and servicing rear brake pads involves inspecting their condition before replacement when they reach maximum wear specifications. The rear wheel brake hose does not need removal when performing this maintenance task. The disc brake caliper must be removed so operators can keep grease, oil, brake fluid and contaminants away from brake pads while performing the service. You should remove the brake pads by pushing at the inner side and rotating them upward which requires wood blocks or old pads as protection for the piston and boots throughout caliper piston retraction into the rear disc brake caliper. Verify that both slippers maintain clean condition and excellent state of repair. A fundamental step during new brake pad installation involves putting all brake pads in full axle sets while avoiding the practice of using new brake pads on a single side of the vehicle. Correct brake operation needs to be checked after reinstalling the rear disc brake caliper and installing the brake pads.

How to service the front brake pads on Mercury Grand Marquis?

Start brake pad service by cleaning the working area then checking the brake fluid level in the master cylinder using the filler cap for removal and trim the fluid to half-full. The air suspension switch inside the luggage compartment needs to be disabled when servicing a vehicle with air suspension systems to avoid unwanted air pressure changes. Start the service procedure by taking off the wheel with tire attached. Avoid inserting tools into the caliper sight hole since it could harm pistons while damaging their boots. The lower brake caliper bolt needs removal before the upper one is loosened to detach the lining from the caliper that requires upward rotation. Take out the pads along with the stainless steel slippers from the anchor plate before disposing of the slippers. The protective measure for pistons and boots involves using a wood block or an old brake pad to invest a C-clamp when compressing brake caliper pistons. After reversing all steps appropriate for installation complete by filling the master cylinder reservoir with new brake fluid and reattaching the filler cap. A final step should include braking operations that extend beyond pedal usage before operating the automobile.

OEM Mercury Grand Marquis Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Brake Pads found

View related parts
Mercury Grand Marquis Brake Pads Part Number: 1U2Z-2V200-SA
$30.64 MSRP: $42.39
You Save: $11.75 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Shoe And Lining; Disc Brake Pad Set; Rear Pads
- Replaces: XU2Z-2V200-XA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Brake Pads, Rear Part Number: 4U2Z-2V200-CA
$44.51 MSRP: $66.65
You Save: $22.14 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Shoe And Lining; Disc Brake Pad Set, Rear; Rear Pads
- Position: Rear
- Replaces: 4W1Z-2200-AA, 6W1Z-2200-AA, BRF-1040
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Mercury Grand Marquis | GS, GSL, Limited Edition, LS, LSE, Ultimate Edition | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Front Pads Part Number: 1U2Z-2V001-KA
$36.74 MSRP: $49.99
You Save: $13.25 (27%)
ADD TO CART
Product Specifications
- Other Name: Pad; Disc Brake Pad Kit; Brake Pads
- Replaces: F4ZZ-2001-A, XU2Z-2V001-BFA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1991 Mercury Grand Marquis | Base, Colony Park, GS, LS | 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS
View related parts
Mercury Grand Marquis Brake Pads Part Number: 1U2Z-2V001-GA
$26.83 MSRP: $36.51
You Save: $9.68 (27%)
ADD TO CART
Product Specifications
- Other Name: Pad; Front Pads
- Replaces: XU2Z-2V001-BCA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Brake Pads, Front Part Number: 4U2Z-2V001-A
$44.51 MSRP: $66.65
You Save: $22.14 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: 3W1Z-2001-AA, BR-931-B, 4U2Z-2V001-BA, 6W1Z-2001-A, BRF-931-A, G2MZ-2V001-Z
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Mercury Grand Marquis | GS, GSL, Limited Edition, LS, LSE, Ultimate Edition | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Brake Pads Part Number: 2U2Z-2V001-ZA
$50.52 MSRP: $68.75
You Save: $18.23 (27%)
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Front Pads
- Manufacturer Note: Motorcraft SuperDuty Brake Pads
- Replaces: BRF-748-A, F8VZ-2001-AA, F8AZ-2001-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Brake Pads, Front Part Number: 2U2Z-2V001-KA
$50.07 MSRP: $74.98
You Save: $24.91 (34%)
ADD TO CART
Product Specifications
- Other Name: Pad; Disc Brake Pad Set; Front Pads
- Position: Front
- Replaces: F5AZ-2001-A, XU2Z-2V001-YA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Brake Pads Part Number: 1U2Z-2V200-KA
$41.33 MSRP: $56.24
You Save: $14.91 (27%)
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Shoe And Lining; Disc Brake Pad Set; Rear Pads
- Replaces: XU2Z-2V200-AAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2000 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Brake Pads Part Number: 1U2Z-2V001-DA
Product Specifications
- Other Name: Pad; Disc Brake Pad Set; Front Pads
- Manufacturer Note: EXC. POLICE
- Replaces: XU2Z-2V001-ADA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1994 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Brake Pads Part Number: 2W1Z-2200-AA
Product Specifications
- Other Name: Kit - Brake Shoe And Lining; Disc Brake Pad Set; Rear Pads
- Replaces: 1W1Z-2200-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2002 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS

Mercury Grand Marquis Brake Pads

OEM Brake Pads boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Pads with long life and a perfect fit. Come to our website and find genuine Mercury Grand Marquis parts. We keep a wide inventory of OEM Grand Marquis parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Brake Pads in Mercury Grand Marquis are an important braking system of the vehicle that helps in halting the automobile by rubbing it against Brake Rotor. They are composites of a friction compound on a metal backing plate with the friction compound wearing out and having to be replaced from time to time. Some Grand Marquis models have wear sensors or indicators that notify the driver about the minimum pad thickness, thus timely detection of when the pads need replacement. As for the brake pad, several versions have been used on the Grand Marquis, non-metallic, semi-metallic, and ceramic. They all have characteristic features in regard to the coefficient of friction, wear and noise. It is important that brake pads be installed correctly usually involving clips and springs where necessary for the pads to work well and to last long. Primarily, the issue of brake fade and different rates of wear, a car require service every 50,000 miles.

Mercury Grand Marquis Brake Pads Parts and Q&A

Brake Pads
2W1Z-2200-AA
Q: How to service and repair the rear brake pads on Mercury Grand Marquis?
A:
Starting the process of repairing and servicing rear brake pads involves inspecting their condition before replacement when they reach maximum wear specifications. The rear wheel brake hose does not need removal when performing this maintenance task. The disc Brake Caliper must be removed so operators can keep grease, oil, brake fluid and contaminants away from brake pads while performing the service. You should remove the brake pads by pushing at the inner side and rotating them upward which requires wood blocks or old pads as protection for the Piston and boots throughout caliper piston retraction into the rear disc brake caliper. Verify that both slippers maintain clean condition and excellent state of repair. A fundamental step during new brake pad installation involves putting all brake pads in full axle sets while avoiding the practice of using new brake pads on a single side of the vehicle. Correct brake operation needs to be checked after reinstalling the rear disc brake caliper and installing the brake pads.
Brake Pads, Front
4U2Z-2V001-A
Q: How to service the front brake pads on Mercury Grand Marquis?
A:
Start brake pad service by cleaning the working area then checking the brake fluid level in the master cylinder using the filler cap for removal and trim the fluid to half-full. The air suspension switch inside the luggage compartment needs to be disabled when servicing a vehicle with air suspension systems to avoid unwanted air pressure changes. Start the service procedure by taking off the wheel with tire attached. Avoid inserting tools into the caliper sight hole since it could harm Pistons while damaging their boots. The lower brake caliper bolt needs removal before the upper one is loosened to detach the lining from the caliper that requires upward rotation. Take out the pads along with the stainless steel slippers from the anchor plate before disposing of the slippers. The protective measure for pistons and boots involves using a wood block or an old brake pad to invest a C-clamp when compressing brake caliper pistons. After reversing all steps appropriate for installation complete by filling the master cylinder reservoir with new brake fluid and reattaching the filler cap. A final step should include braking operations that extend beyond pedal usage before operating the automobile.