How to service the rear ABS sensor on Mercury Mariner?

Start the service process of the rear ABS sensor by placing the vehicle on a hoist with neutral gear position. Handle the grommet removal with caution because a damaged grommet requires replacing the sensor regardless of its operational condition. Swivel the grommet until it exposes access to two tabs on right angles relative to the sensor wire which can be released with a small screwdriver. You should disconnect the rear ABS sensor electrical connector before pulling out the harness from its retaining point. Secure the three bolts holding the rear ABS sensor harness until they reach 9 Nm (80 lb-inch). Reinstall each bolt with this torque during the installation process. The sensor area must be cleaned thoroughly before you remove the rear ABS sensor bolt from the wheel knuckle. Also, reposition it with 9 Nm (80 lb-inch) torque when performing reinstallation. Finish the repair work by cleaning the mounting surface thoroughly before going through the opposite steps to install it.

How to service the front ABS sensor on Mercury Mariner?

Service of the front ABS sensor begins after setting the vehicle in neutral position on a hoist. The electrical connection in the engine compartment needs removal before body plug replacement if the plug becomes damaged as this will require a new sensor installation even if the sensor works properly. Hold the body plug in position for release of the two tabs at right angles to the sensor wire by using a small screwdriver. To remove the front ABS sensor wire first detach it from the retainer then remove the wire-to-body bolt which needs to be tightened at 9 Nm (80 inch lbs.) during installation. After removing the front ABS sensor bolt it needs to be retightened using 15 Nm (11 ft. lbs.) torque during the reassembly process. After removing the front ABS sensor bolt from the wheel knuckle continue by tightening it to 9 Nm (80 inch lbs.) when replacing the bolt. It is essential to initially wipe away debris that has gathered near the sensor before conducting the front ABS sensor removal operations while also cleaning the mounting surface before reinstating the equipment.

OEM Mercury Mariner ABS Sensor

ABS Wheel Speed Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 ABS Sensors found

View related parts
Mercury Mariner ABS Sensor, Front Driver Side Part Number: YL8Z-2C205-AB
$36.98 MSRP: $58.73
You Save: $21.75 (38%)
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Front Left; Sensor, Wheel Speed; ABS Speed Sensor; Front Speed Sensor; ABS Wheel Speed Sensor
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Mercury Mariner | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner ABS Sensor, Front Driver Side Part Number: 9L8Z-2C205-A
$49.46 MSRP: $78.55
You Save: $29.09 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Front Left; ABS Speed Sensor; Front Speed Sensor; ABS Wheel Speed Sensor
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner ABS Sensor, Front Passenger Side Part Number: 9L8Z-2C204-A
$48.17 MSRP: $80.73
You Save: $32.56 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Front Right; Front Speed Sensor
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner ABS Sensor, Rear Driver Side Part Number: 9L8Z-2C191-A
$55.03 MSRP: $90.55
You Save: $35.52 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Rear Left; Rear Speed Sensor
- Manufacturer Note: Rear
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner ABS Sensor, Rear Passenger Side Part Number: 9L8Z-2C190-A
$45.00 MSRP: $71.45
You Save: $26.45 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Rear Right; Rear Speed Sensor
- Manufacturer Note: Rear
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner ABS Sensor, Rear Driver Side Part Number: 8L8Z-2C191-A
$38.59 MSRP: $61.27
You Save: $22.68 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Rear Left; ABS Speed Sensor; Rear Speed Sensor; ABS Wheel Speed Sensor
- Manufacturer Note: Rear
- Position: Rear Driver Side
- Replaces: 5L8Z-2C216-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mercury Mariner | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner ABS Sensor, Rear Passenger Side Part Number: 8L8Z-2C190-A
$44.88 MSRP: $71.27
You Save: $26.39 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Rear Right; Rear Speed Sensor; ABS Wheel Speed Sensor
- Manufacturer Note: Rear
- Position: Rear Passenger Side
- Replaces: 5L8Z-2C190-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mercury Mariner | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner ABS Sensor, Front Passenger Side Part Number: YL8Z-2C204-AB
$62.21 MSRP: $102.36
You Save: $40.15 (40%)
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Front Right; Sensor, Wheel Speed; ABS Speed Sensor; Front Speed Sensor; ABS Wheel Speed Sensor
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Mercury Mariner | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Rear Speed Sensor, Passenger Side Part Number: YL8Z-2C190-AC
$36.11 MSRP: $49.14
You Save: $13.03 (27%)
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor; ABS Sensor
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Mariner | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner ABS Sensor, Rear Driver Side Part Number: AL8Z-2C190-B
$76.64 MSRP: $106.02
You Save: $29.38 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Rear Left; Rear Speed Sensor
- Manufacturer Note: Rear
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner ABS Sensor, Rear Passenger Side Part Number: AL8Z-2C190-A
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Rear Right; Rear Speed Sensor
- Manufacturer Note: Rear
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Rear Speed Sensor, Driver Side Part Number: YL8Z-2C216-AC
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor; ABS Speed Sensor; ABS Sensor
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Mariner | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

Mercury Mariner ABS Sensor

OEM ABS Sensor boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Sensor with long life and a perfect fit. Come to our website and find genuine Mercury Mariner parts. We keep a wide inventory of OEM Mariner parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Mercury Mariner ABS Sensor is one of the significant components of the Anti-lock Braking System (ABS), in Mercury Mariner cars recognized globally for their dependability and speed. This sensor pays a lot of attention to the number of rotations of the wheel and feeds the computer with this information which is important in the control of safe and steady braking. Since the Mercury Mariner ABS Sensor allows for non-locking of the wheels during difficult conditions, it improves upon efficiency and safety all in one. Fitted to wide range of Mercury Mariner years, this ABS Sensor uses Hall effect sensors or toothed wheels with electromagnetic coils to provide accurate voltage signals allowing the braking pressure to be amended in real time. It may lose some of its functionality when car speeds are low but, the design makes the ABS Sensor to continue being a reliable part of the braking system. The Mercury Mariner which is a compact crossover SUV launched in 2005 has been rated as the consumers digest premier buy and 2006 Green car of the year for the hybrid model. It is for this reason that the Mercury Mariner ABS Sensor offers an interface with such features as pull-drift steering compensation among others. Therefore, the Mercury Mariner ABS Sensor is all about reliability and is one of the components that contribute to the safety and the performance of the Mercury Mariner which makes it an essential part of this magnificent vehicle.

Mercury Mariner ABS Sensor Parts and Q&A

ABS Sensor, Rear Passenger Side
8L8Z-2C190-A
Q: How to service the rear ABS sensor on Mercury Mariner?
A:
Start the service process of the rear ABS sensor by placing the vehicle on a hoist with neutral gear position. Handle the grommet removal with caution because a damaged grommet requires replacing the sensor regardless of its operational condition. Swivel the grommet until it exposes access to two tabs on right angles relative to the sensor wire which can be released with a small screwdriver. You should disconnect the rear ABS sensor electrical connector before pulling out the harness from its retaining point. Secure the three bolts holding the rear ABS sensor harness until they reach 9 Nm (80 lb-inch). Reinstall each bolt with this torque during the installation process. The sensor area must be cleaned thoroughly before you remove the rear ABS sensor bolt from the wheel knuckle. Also, reposition it with 9 Nm (80 lb-inch) torque when performing reinstallation. Finish the repair work by cleaning the mounting surface thoroughly before going through the opposite steps to install it.
ABS Sensor, Front Driver Side
YL8Z-2C205-AB
Q: How to service the front ABS sensor on Mercury Mariner?
A:
Service of the front ABS sensor begins after setting the vehicle in neutral position on a hoist. The electrical connection in the engine compartment needs removal before body plug replacement if the plug becomes damaged as this will require a new sensor installation even if the sensor works properly. Hold the body plug in position for release of the two tabs at right angles to the sensor wire by using a small screwdriver. To remove the front ABS sensor wire first detach it from the retainer then remove the wire-to-body bolt which needs to be tightened at 9 Nm (80 inch lbs.) during installation. After removing the front ABS sensor bolt it needs to be retightened using 15 Nm (11 ft. lbs.) torque during the reassembly process. After removing the front ABS sensor bolt from the wheel knuckle continue by tightening it to 9 Nm (80 inch lbs.) when replacing the bolt. It is essential to initially wipe away debris that has gathered near the sensor before conducting the front ABS sensor removal operations while also cleaning the mounting surface before reinstating the equipment.