How to Service and Repair the Rear Brake Line Flexible Hose on Mercury Milan?

The first step to service the rear brake flexible hose includes tire and wheel removal then continuing with the brake caliper flow bolt removal. Before installation replace the new bolt with a torque of 25 Nm (18 lb-ft) after removing the brake caliper flow bolt as well as discarding the two copper washers. When replacing the brake tube fitting on the brake flexible hose tighten it to 17 Nm torque value (13 lb-ft). Start by untightening both the brake flexible hose retaining clip along with the entire brake hose. The brake caliper should get its bleed procedure after executing the installation steps backwards. Bleeding brake systems requires new brake fluid of clean condition which must match manufacturing specifications because using recycled fluid could harm the system through contamination. Precautions should be taken to protect painted and plastic surfaces from brake fluid because exposure can create damage; any spillages should be cleaned with water instantly. Users needing emergency medical information about brake fluid should dial 1-800-959-3673 in both Canada and the United States and should also access the product Material Safety Data Sheet (MSDS) when it is available.

How to Service and Repair the Front Brake Line Flexible Hose on Mercury Milan?

You must start the front brake flexible hose servicing and repair process by using clean brake fluid that matches manufacturer standards while avoiding earlier drained fluid since contaminated materials could damage the system. The product label for Ford/Motorcraft products in the USA or Canada requires careful review of the cautionary information which demands emergency medical advice through a call to 1-800-959-3673. Obtain knowledge from the Material Safety Data Sheet (MSDS) by following its directions. Plan your work to steer clear of brake fluid interaction with painted surfaces and plastic materials since they will suffer damage. In case of contact, immediately rinse the affected area with water. The service begins with removing the brake caliper flow bolt and discarding the two copper washers before tightening the new bolt to 25 Nm (18 lb-ft) when reinstalling the bolt. When reinstalling the brake tube fitting onto the brake flexible hose tighten it to 17 Nm (13 lb-ft). Detaching the brake flexible hose requires removing its two bracket bolts before subsequent installation requires torquing these bolts to 20 Nm (15 lb-ft). The brake system complete service ends with bleeding of the fluid after reversing the removal procedure.

OEM Mercury Milan Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Brake Lines found

View related parts
Mercury Milan Flex Hose, Front Passenger Side Part Number: AE5Z-2078-F
$55.23 MSRP: $92.55
You Save: $37.32 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Front Right; Brake Hose; Brake Line; Hydraulic Hose
- Position: Front Passenger Side
- Replaces: AE5Z-2078-B, AE5Z-2078-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Flex Hose, Front Driver Side Part Number: AE5Z-2078-E
$52.30 MSRP: $87.64
You Save: $35.34 (41%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Front Left; Brake Hose; Brake Line; Hydraulic Hose
- Position: Front Driver Side
- Replaces: AE5Z-2078-C, AE5Z-2078-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Flex Hose, Rear Driver Side Part Number: 9E5Z-2283-B
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Rear Left; Brake Hose; Brake Line; Hydraulic Hose
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Flex Hose, Rear Passenger Side Part Number: 9E5Z-2282-B
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Rear Right; Brake Hose; Brake Line; Hydraulic Hose
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Flex Hose, Rear Part Number: 7E5Z-2A442-A
Product Specifications
- Other Name: Hose Assembly; Brake Hydraulic Hose, Rear; Brake Hose; Brake Line; Hydraulic Hose
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Flex Hose, Front Part Number: 6E5Z-2282-AA
Product Specifications
- Other Name: Hose Assembly - Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Flex Hose, Front Driver Side Part Number: 6E5Z-2078-AA
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Front Left; Brake Hose; Brake Line; Hydraulic Hose
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Flex Hose, Driver Side Part Number: 9E5Z-2283-A
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Rear Left; Brake Hose; Brake Line; Hydraulic Hose
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Milan | Base, Hybrid, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Flex Hose, Front Passenger Side Part Number: 6E5Z-2078-BA
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Front Right; Brake Hose; Brake Line; Hydraulic Hose
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Flex Hose, Passenger Side Part Number: 9E5Z-2282-A
Product Specifications
- Other Name: Hose Assembly - Brake; Brake Hydraulic Hose, Rear Right; Brake Hose; Brake Line; Hydraulic Hose
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Milan | Base, Hybrid, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

Mercury Milan Brake Line

OEM Brake Line boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Line with long life and a perfect fit. Come to our website and find genuine Mercury Milan parts. We keep a wide inventory of OEM Milan parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Mercury Milan Brake Line is an important part of the hydraulic system responsible for transmitting brake fluid picked from the master cylinder to the brake caliper pistons with a view of stopping or slowing down the vehicle. Being associated with reliability and performance, the Mercury Milan Brake Line added security to various models of Milan that has been manufactured between the years 2006 to 2011. Mercury Milan is a mid-size sedan which well-known for its strong builds and one among them is the Brake Line who enables the car to bear several types of conditions of driving. Brake Line options such as the braided stainless steel thus allows the driver to feel, and respond to, better pedal feel as opposed to the many issues which come with the standard rubber hoses which may expand with pressure. The Mercury Milan Brake Line is protected against corrosion and other forms of physical destruction so that it can be useful and reliable for a long period. Further, new generation brake line kits are prebent to fit standard car Weltmeister configurations, making replacement easier and more efficient as it is sure to fit and work as expected. This focus is something that is often unique within the Mercury Milan Brake Line where not only is the feel of the car improved but safety is made a priority. In all, the Mercury Milan Brake Line is a clear demonstration of Mercury auto's ability to deliver quality products to the market that will give drivers the assurance they need on the road.

Mercury Milan Brake Line Parts and Q&A

Flex Hose, Rear
7E5Z-2A442-A
Q: How to Service and Repair the Rear Brake Line Flexible Hose on Mercury Milan?
A:
The first step to service the rear brake flexible hose includes tire and wheel removal then continuing with the Brake Caliper flow bolt removal. Before installation replace the new bolt with a torque of 25 Nm (18 lb-ft) after removing the brake caliper flow bolt as well as discarding the two copper washers. When replacing the brake tube fitting on the brake flexible hose tighten it to 17 Nm torque value (13 lb-ft). Start by untightening both the brake flexible hose retaining clip along with the entire brake hose. The brake caliper should get its bleed procedure after executing the installation steps backwards. Bleeding brake systems requires new brake fluid of clean condition which must match manufacturing specifications because using recycled fluid could harm the system through contamination. Precautions should be taken to protect painted and plastic surfaces from brake fluid because exposure can create damage; any spillages should be cleaned with water instantly. Users needing emergency medical information about brake fluid should dial 1-800-959-3673 in both Canada and the United States and should also access the product Material Safety Data Sheet (MSDS) when it is available.
Flex Hose, Front Passenger Side
6E5Z-2078-BA
Q: How to Service and Repair the Front Brake Line Flexible Hose on Mercury Milan?
A:
You must start the front brake flexible hose servicing and repair process by using clean brake fluid that matches manufacturer standards while avoiding earlier drained fluid since contaminated materials could damage the system. The product label for Ford/Motorcraft products in the USA or Canada requires careful review of the cautionary information which demands emergency medical advice through a call to 1-800-959-3673. Obtain knowledge from the Material Safety Data Sheet (MSDS) by following its directions. Plan your work to steer clear of brake fluid interaction with painted surfaces and plastic materials since they will suffer damage. In case of contact, immediately rinse the affected area with water. The service begins with removing the brake caliper flow bolt and discarding the two copper washers before tightening the new bolt to 25 Nm (18 lb-ft) when reinstalling the bolt. When reinstalling the brake tube fitting onto the brake flexible hose tighten it to 17 Nm (13 lb-ft). Detaching the brake flexible hose requires removing its two bracket bolts before subsequent installation requires torquing these bolts to 20 Nm (15 lb-ft). The brake system complete service ends with bleeding of the fluid after reversing the removal procedure.