How to Safely Service and Repair a Fuel Pump Module on Mercury Milan?

The high flammability of mixtures inside the fuel gauge sender and fuel pump module demands necessary safety guidelines before maintenance operations. The first step should include lowering fuel system pressure followed by disconnecting the battery ground cable. You should turn the fuel tank filler cap counterclockwise about one-fourth turn before placing it safely to the side. The procedure for removing the Fuel Draining Hose involves slight shaking movements to prevent the fitting from breaking loose while the hose should be inserted into the fuel tank filler pipe until the fitting activates the safety valve. The Fuel Storage Tanker should be connected to the Fuel Draining Hose for drawing out one-eighth of the fuel tank volume until the fuel sits below the fuel pump module mounting flange. Begin by removing the rear seat lower cushion and then proceed to take four screws off the fuel pump module access cover for front-wheel drive vehicles but use three screws for all-wheel drive vehicles. The user should disconnect both the fuel pump module electrical connection and the quick connect coupling between the fuel tube and the fuel pump module. The technician should place absorbent pads on the floor pan before carefully removing the fuel pump module from the vehicle while installing a new fuel pump module O-ring seal and lock ring. The Fuel Tank Sender Unit Wrench should be used to eliminate and dispose of the fuel pump module lock ring. All-wheel drive vehicles require the fuel pump module to be lifted from the fuel tank for exposing the quick connect coupling between the fuel tube and fuel pump module. Take care with the fuel pump module handling to protect the float arm while you fill fuel residue into appropriate storage. A replacement of either the fuel pump module or fuel tank is necessary if any evidence of bending, scratching or corrosion is present on their contact surface areas during mating surface inspection. Clean engine oil must be applied to the new O-ring seal for installation then the repair procedure should be done in reverse order while checking for proper alignment of the fuel pump module alignment tab with the fuel tank before tightening the lock ring.

OEM Mercury Milan Fuel Pump

Gas Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Fuel Pumps found

View related parts
Mercury Milan Fuel Pump Part Number: AE5Z-9H307-L
$329.60 MSRP: $547.27
You Save: $217.67 (40%)
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump and Sender Assembly; Fuel Pump Module Assembly; Electric Fuel Pump; Fuel Pump Assembly
- Manufacturer Note: Service Kit
- Replaces: AE5Z-9H307-E, PFS-542
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Premier | 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Fuel Gauge Sending Unit, Passenger Side Part Number: 7E5Z-9275-C
$66.79 MSRP: $92.40
You Save: $25.61 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger; Sending Unit; Fuel Level Sensor; Fuel Pump.; Fuel Pump Assembly; Fuel Sender Unit
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Fuel Pump Part Number: 7E5Z-9H307-T
$241.00 MSRP: $363.64
You Save: $122.64 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007 Mercury Milan | Base, Premier | 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Fuel Pump Part Number: AE5Z-9H307-K
$341.64 MSRP: $567.27
You Save: $225.63 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump and Sender Assembly; Fuel Pump Module Assembly; Electric Fuel Pump; Fuel Pump Assembly
- Manufacturer Note: Service Kit
- Replaces: PFS-541, AE5Z-9H307-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Fuel Pump Part Number: AE5Z-9H307-F
$209.15 MSRP: $347.27
You Save: $138.12 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump and Sender Assembly; Electric Fuel Pump; Fuel Pump Module Assembly; Fuel Pump Assembly
- Manufacturer Note: Service Kit
- Replaces: AE5Z-9H307-A, PFS-538
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
View related parts
Mercury Milan Fuel Pump Part Number: 8E5Z-9H307-T
$221.49 MSRP: $376.36
You Save: $154.87 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump and Sender Assembly; Fuel Pump Module Assembly; Strainers & Misc Prt; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Milan | Base, Premier | 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Fuel Pump Part Number: 8E5Z-9H307-S
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS
View related parts
Mercury Milan Fuel Pump Part Number: 7E5Z-9H307-U
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2009 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Milan Fuel Pump Part Number: 7E5Z-9H307-S
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Replaces: 6E5Z-9H307-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Mercury Milan | Base, Premier | 4 Cyl 2.3 L GAS
View related parts
Mercury Milan Fuel Gauge Sending Unit Part Number: AE5Z-9275-A
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender & Hanger Assembly; Fuel Level Sensor; Sending Unit; Fuel Sender Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Mercury Milan | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Milan Fuel Pump Part Number: 6E5Z-9H307-G
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Strainers & Misc Parts; Electric Fuel Pump; Fuel Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Mercury Milan | Base, Premier | 6 Cyl 3.0 L GAS

Mercury Milan Fuel Pump

OEM Fuel Pump boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Fuel Pump with long life and a perfect fit. Come to our website and find genuine Mercury Milan parts. We keep a wide inventory of OEM Milan parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Fuel Pump is one of the important parts that signify the solidity and the power of the Mercury Milan lines and help in achieving optimal levels of fuel flow from the tank to the engine. The Fuel Pump is well known for keen design; it efficiently employs advanced electric methods widespread in the fuel tank with pressure management at levels of 40-60 psi. This electric fuel pump not only improves the burning of fuel but also contributes in safety of Mercury Milan by ensuring steady flow of fuel regulated by ECUs. Fitment with the Mercury Milan models manufactured from 2006 to 2011 guarantees that an individual enjoys upgraded efficiency and power in every model. Fuel Pump is one of the outstanding products in the market since it uses the pulse-width modulation to increase firmness and decrease power usage making it suitable for modern Mercury Milan. What is more, the design solutions of Mercury Milan, including short-long arm double wishbone front suspension and independent multi-link rear suspension, perfectly harmonize with the work of the fuel pump and provide a smooth and interesting ride. In sum, the Fuel Pump is not merely an anatomic item; it is a symbol of Mercury's brand essential constituent of quality, safety, and innovation, which makes it significant to consider if you are a Mercury Milan owner who would like your car to run efficiently.

Mercury Milan Fuel Pump Parts and Q&A

Fuel Pump
8E5Z-9H307-T
Q: How to Safely Service and Repair a Fuel Pump Module on Mercury Milan?
A:
The high flammability of mixtures inside the fuel gauge sender and fuel pump module demands necessary safety guidelines before maintenance operations. The first step should include lowering fuel system pressure followed by disconnecting the battery ground cable. You should turn the fuel tank filler cap counterclockwise about one-fourth turn before placing it safely to the side. The procedure for removing the Fuel Draining Hose involves slight shaking movements to prevent the fitting from breaking loose while the hose should be inserted into the fuel tank filler pipe until the fitting activates the safety valve. The Fuel Storage Tanker should be connected to the Fuel Draining Hose for drawing out one-eighth of the fuel tank volume until the fuel sits below the fuel pump module mounting flange. Begin by removing the rear seat lower cushion and then proceed to take four screws off the fuel pump module access cover for front-wheel drive vehicles but use three screws for all-wheel drive vehicles. The user should disconnect both the fuel pump module electrical connection and the quick connect coupling between the fuel tube and the fuel pump module. The technician should place absorbent pads on the floor pan before carefully removing the fuel pump module from the vehicle while installing a new fuel pump module O-ring seal and lock ring. The Fuel Tank Sender Unit Wrench should be used to eliminate and dispose of the fuel pump module lock ring. All-wheel drive vehicles require the fuel pump module to be lifted from the fuel tank for exposing the quick connect coupling between the fuel tube and fuel pump module. Take care with the fuel pump module handling to protect the float arm while you fill fuel residue into appropriate storage. A replacement of either the fuel pump module or fuel tank is necessary if any evidence of bending, scratching or corrosion is present on their contact surface areas during mating surface inspection. Clean engine oil must be applied to the new O-ring seal for installation then the repair procedure should be done in reverse order while checking for proper alignment of the fuel pump module alignment tab with the fuel tank before tightening the lock ring.