How to Service and Repair the Vapor Canister on Mercury Montego?

The first step for EVAP canister service and repair requires the vehicle to be in neutral position and positioned on a hoist. To prevent electrical sparks you should detach the battery ground cable. All personal electronic devices should remain off-hand and both smoking and open flame use must be eliminated near fuel-related parts because highly flammable mixtures exist in that area. Proceed by cutting off the electrical cable from the EVAP canister vent solenoid along with the quick-connect fitting of the EVAP vapor tube. You must first remove the EVAP front fuel vapor tube from the dust box before removing the two required EVAP canister retaining nuts which should be tightened to 9 Nm (80 lb-in) after reinstallation. When replacing the EVAP canister install its retaining bolts with a torque of 9 Nm (80 lb-in). These bolts need to be installed to the same torque setting. Three pushpin retainers on the wire harness need release before the EVAP canister can be taken out. The installation process ends with performing both leakage tests and the evaporative emission remedy verification drive cycle after reversing the removal steps.

OEM Mercury Montego Vapor Canister

Fuel Vapor Canister

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Vapor Canisters found

View related parts
Mercury Montego Vapor Canister Part Number: 7G1Z-9D653-C
Product Specifications
- Other Name: Reservoir Assembly; Vapor Canister Purge Solenoid
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007 Mercury Montego | Luxury, Premier | 6 Cyl 3.0 L GAS
View related parts
Mercury Montego Vapor Canister Part Number: 7G1Z-9D653-D
Product Specifications
- Other Name: Cannister - Fuel Vapour Storage; Vapor Canister Purge Solenoid
- Replaces: 6G1Z-9D653-AA, 7G1Z-9D653-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Montego | Luxury, Premier | 6 Cyl 3.0 L GAS

Mercury Montego Vapor Canister

OEM Vapor Canister boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Vapor Canister with long life and a perfect fit. Come to our website and find genuine Mercury Montego parts. We keep a wide inventory of OEM Montego parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Vapor Canister is a critical part of the evaporative emissions control (EVAP) system and has proved to be a reliable and high performing part in most Montego models. This revolutionary Vapor Canister is for storage of fuel vapors which are generated from the fuel tank to avoid emission of hydrocarbons in the atmosphere. The Vapor Canister releases these vapors into the engine and combusted hence augmenting efficiency and safety given that the engine will perform within the set environmental standards. In particular, the canister is equipped with activated charcoal as it provides the biggest available surface for adsorptive procedures in the case of evolving vapors. The Vapor Canister has had many versions over the lifetime of the Mercury Montego, and some of the newer versions even come with replaceable filters as well as canister vent solenoids and fuel tank pressure sensors. All of these improvements do not only affect the performances of the canister but it also increases the dependable value of the Mercury Montego. The third generation of the Montego, built from 2005 to 2007 also show Spear's adherence to quality that goes with dealerships, advanced amenities as well as safety features that enriched the drive of the third generation Montego. The Vapor Canister is very much distinctive and also sturdy and thus is very marketable on the automobile market because it adds to the dependability of the Mercury Montego while at the same time making the world a greener place to live in. In summary, the Mercury Montego along with the Vapor Canister appears as a package of comfort, power, security as well as a wise consciousness towards the environment.

Mercury Montego Vapor Canister Parts and Q&A

Vapor Canister
7G1Z-9D653-D
Q: How to Service and Repair the Vapor Canister on Mercury Montego?
A:
The first step for EVAP canister service and repair requires the vehicle to be in neutral position and positioned on a hoist. To prevent electrical sparks you should detach the battery ground cable. All personal electronic devices should remain off-hand and both smoking and open flame use must be eliminated near fuel-related parts because highly flammable mixtures exist in that area. Proceed by cutting off the electrical cable from the EVAP canister vent solenoid along with the quick-connect fitting of the EVAP vapor tube. You must first remove the EVAP front fuel vapor tube from the dust box before removing the two required EVAP canister retaining nuts which should be tightened to 9 Nm (80 lb-in) after reinstallation. When replacing the EVAP canister install its retaining bolts with a torque of 9 Nm (80 lb-in). These bolts need to be installed to the same torque setting. Three pushpin retainers on the wire harness need release before the EVAP canister can be taken out. The installation process ends with performing both leakage tests and the evaporative emission remedy verification drive cycle after reversing the removal steps.