How to service and repair the ABS Control Module on Mercury Sable?

Professional service requirements for the Electronic Brake Control Module start with removing the battery tray. The wiring connector lock must be detached before you remove the attached wires. The service starts with brake line detachment before removing bolts which support the electronic control unit (ECU)/hydraulic control unit (HCU) assembly. The ECU can be pulled out after the wires are detached and then all screws are removed. The nuts should be partially opened to detach the bracket assembly. The brake system should be bled afterward during installation when you follow the opposite order of removal steps. Brake components will sustain permanent damage along with brake failure from using any brake fluid other than DOT 3 or DOT 4 which have received specific approval. Use proper caution when dealing with brake fluid because any contact with eyes should be avoided and proper hand washing is required after fluid interaction. After exposure to your eyes continue washing with running water for 15 minutes and obtain medical help if eye discomfort continues. Swallowing any amount of fluid requires water drinking followed by vomiting inducement and quick medical consultation. Brake fluid exposure can harm painted and plastic surfaces which requires a prompt clean-up with water. During bleeding operations always maintain the master cylinder reservoir with brake fluid of the specified type while avoiding any reuse of hydraulic system drained brake fluid.

How to Bleed the Brake System After Installing a New Four-Wheel ABS Control Module on Mercury Sable?

Cleaning the dirt from the brake master cylinder filler cap is the first step before filling it with DOT 3 or DOT 4 brake fluid according to specification while constantly monitoring the master cylinder reservoir to prevent running dry during the bleeding procedure. The bleeder screw on the right-hand (RH) rear involves attaching a drain tube with a clear tube to the screw to collect brake fluid in an equally filled container. During the bleeder screw procedure an assistant must pump the brake pedal with steady pressure until the RH rear bleeder screw produces a continuous stream of transparent brake fluid without bubbles, before the screw gets tightened. Continue the procedure as needed by adding more brake master cylinder reservoir fluid when necessary. Complete the procedure by following the same sequence to tighten the LH rear bleeder screw then the RH front bleeder screw and finally the LH front bleeder screw. Bleeding ends with connecting the NGS DLC cable adapter to the dash-mounted vehicle data link connector (DLC) before accessing the help menu on the scan tool through Ford Service Function Card (FSF) according to the provided instructions. The bleeding process should end with a repetition of the original bleeder procedure. Demarcate adequate care with brake fluid management because it can instigate permanent brake component destruction as well as harm painted equipment and plastic materials.

OEM Mercury Sable ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 ABS Control Modules found

View related parts
Mercury Sable Control Module Part Number: 9G1Z-2C219-B
$1257.30 MSRP: $1719.38
You Save: $462.08 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module; Module
- Replaces: 9G1Z-2C219-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Control Module Part Number: 8G1Z-2C219-D
$588.51 MSRP: $814.15
You Save: $225.64 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 8G1Z-2C219-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Control Module Part Number: 8G1Z-2C219-F
Product Specifications
- Other Name: Control; ABS Control Module; Module
- Replaces: 8G1Z-2C219-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Control Module Part Number: 4F1Z-2C219-AA
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Manufacturer Note: ABS only
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Control Module Part Number: YF1Z-2C286-CA
Product Specifications
- Other Name: Control; ABS Hydraulic Assembly; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Control Module Part Number: YF1Z-2C286-BA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulic; ABS Hydraulic Assembly; ABS Control Module; Hydraulic Control Unit; Control Assembly - ABS Hydraulics
- Manufacturer Note: HCU, ABS & traction assist
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Control Module Part Number: YF1Z-2C286-AA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulic; ABS Hydraulic Assembly; ABS Control Module; Hydraulic Control Unit; Control Assembly - ABS Hydraulics
- Manufacturer Note: HCU, ABS only
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Control Module Part Number: YF1Z-2C219-BA
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Manufacturer Note: ABS & Traction assist
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2003 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Control Module Part Number: YF1Z-2C219-AA
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Manufacturer Note: ABS only
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2003 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Modulator Valve Part Number: 9G1Z-2C405-B
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit; Control Assembly
- Replaces: 9G1Z-2C405-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Control Module Part Number: XF1Z-2C219-AA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: except SHO
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Control Module Part Number: F1DZ-2C219-A
Product Specifications
- Other Name: Module And Bracket Assembly - Power Steering; ABS Control Module; Module & Brkt Assembly-Power Steering
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Mercury Sable | GS, LS, LTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Modulator Valve Part Number: 8G1Z-2C346-E
Product Specifications
- Other Name: Module - ABS Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU & HCU
- Replaces: 8G1Z-2C346-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Modulator Valve Part Number: 8G1Z-2C346-D
Product Specifications
- Other Name: Module - ABS Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU & HCU
- Replaces: 8G1Z-2C346-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Control Module Part Number: 8G1Z-2C219-E
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 8G1Z-2C219-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Control Module Part Number: 4F1Z-2C219-BA
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Manufacturer Note: ABS & traction assist, Less Advance Trac
- Replaces: 2F1Z-2C219-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Hydraulic Control Unit Part Number: F6DZ-2C286-BA
Product Specifications
- Other Name: ABS Pump; ABS Pump And Motor Assembly; ABS Control Module; ABS Pump Assembly; Control Assembly - ABS Hydraulics
- Manufacturer Note: SHO
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Modulator Valve Part Number: 8G1Z-2C346-F
$1805.63 MSRP: $2469.23
You Save: $663.60 (27%)
Product Specifications
- Other Name: Module - ABS Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit; Control Assembly
- Manufacturer Note: ECU & HCU
- Replaces: 8G1Z-2C346-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS

Mercury Sable ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Mercury Sable parts. We keep a wide inventory of OEM Sable parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Mercury Sable ABS Control Module is the vital gear that is used in anti-lock braking system and has got popularity dampened due to its reliability and result oriented working in various models of Sable. These modules are vital for the anti-locking of wheels during bulky braking hence improving on the control and safety of vehicles. The Mercury Sable ABS Control Module operates the brake system through the network of wheel speed sensors, valves and the Electronic Control Unit (ECU) to regulate the pressure of ABS modulator enhancing the brake pressure and performance. Its compatibility also extends to multiple generations of the Mercury Sable, therefore it can be recommended for the maintenance of the braking system's integrity. For instance, there is the ABS Control Module has advanced features like the ESC and the traction control; aspects that play a major role in the handling of the vehicle especially in adverse situations. These improvements enable the Mercury Sable to steer and control brake force which is crucial during skid or acceleration. Overall, the ABS system helps to decrease the stopping distances on most types of surface but its effectiveness on one rather important type of surface, loose gravel or snow, must also be taken into consideration. The Mercury Sable, a mid-size sedan known for the advanced modifications in design and functioning, has always included the ABS Control Module to improve the driving experience. Being a reliable Mercury car part the Mercury Sable ABS Control Module is known in the automotive market to be highly durable and packed with unique inviting features meaning that people can rely on their cars to be safe to drive.

Mercury Sable ABS Control Module Parts and Q&A

Control Module
YF1Z-2C219-BA
Q: How to service and repair the ABS Control Module on Mercury Sable?
A:
Professional service requirements for the Electronic Brake Control Module start with removing the battery tray. The wiring connector lock must be detached before you remove the attached wires. The service starts with Brake Line detachment before removing bolts which support the electronic control unit (ECU)/hydraulic control unit (HCU) assembly. The ECU can be pulled out after the wires are detached and then all screws are removed. The nuts should be partially opened to detach the bracket assembly. The brake system should be bled afterward during installation when you follow the opposite order of removal steps. Brake components will sustain permanent damage along with brake failure from using any brake fluid other than DOT 3 or DOT 4 which have received specific approval. Use proper caution when dealing with brake fluid because any contact with eyes should be avoided and proper hand washing is required after fluid interaction. After exposure to your eyes continue washing with running water for 15 minutes and obtain medical help if eye discomfort continues. Swallowing any amount of fluid requires water drinking followed by vomiting inducement and quick medical consultation. Brake fluid exposure can harm painted and plastic surfaces which requires a prompt clean-up with water. During bleeding operations always maintain the master cylinder reservoir with brake fluid of the specified type while avoiding any reuse of hydraulic system drained brake fluid.
Control Module
YF1Z-2C286-CA
Q: How to Bleed the Brake System After Installing a New Four-Wheel ABS Control Module on Mercury Sable?
A:
Cleaning the dirt from the Brake Master Cylinder filler cap is the first step before filling it with DOT 3 or DOT 4 brake fluid according to specification while constantly monitoring the master cylinder reservoir to prevent running dry during the bleeding procedure. The bleeder screw on the right-hand (RH) rear involves attaching a drain tube with a clear tube to the screw to collect brake fluid in an equally filled container. During the bleeder screw procedure an assistant must pump the brake pedal with steady pressure until the RH rear bleeder screw produces a continuous stream of transparent brake fluid without bubbles, before the screw gets tightened. Continue the procedure as needed by adding more brake master cylinder reservoir fluid when necessary. Complete the procedure by following the same sequence to tighten the LH rear bleeder screw then the RH front bleeder screw and finally the LH front bleeder screw. Bleeding ends with connecting the NGS DLC cable adapter to the dash-mounted vehicle data link connector (DLC) before accessing the help menu on the scan tool through Ford Service Function Card (FSF) according to the provided instructions. The bleeding process should end with a repetition of the original bleeder procedure. Demarcate adequate care with brake fluid management because it can instigate permanent brake component destruction as well as harm painted equipment and plastic materials.