How to service and repair the front brake caliper on Mercury Sable?

Service and repair operations of the front brake caliper require beginning with fluid drainage followed by using only DOT 3 or DOT 4 brake fluid to protect brake components from permanent damage. When handling brake fluid users should protect their eyes and wash their hands completely after completion. If eyes come into contact with brake fluid users need to flush them with water for 15 minutes and obtain medical help if signs of irritation appear. Ingesting brake fluid requires you to drink water followed by vomiting induction then you should get medical attention immediately. Beware of brake fluid spills on painted surfaces and plastic constituents since rapid water cleaning will protect them. The disc brake caliper needs to be secured inside a vise before removing its piston through the mechanism of a wood block placed between the caliper bridge and piston then low air pressure applied to the fluid port to push out the piston. Discard the seals together with dust boots when removing the piston and refrain from honing caliper bores due to unavailability of piston-specific calipers. A front disc brake caliper replacement is necessary when you detect bores damage or when leaks prevent proper sealing. For assembling the calipers install new dust boots together with piston seals and replace the brake fluid with DOT 3 or DOT 4 according to Ford specification SAE J1704. High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or a DOT 3 equivalent matching Ford specification ESA-M6C25-A should be used to lubricate both the piston dust boot and piston seal in addition to the caliper piston and caliper bore. Use this fluid when assembling the caliper piston seal and dust boot with caution to prevent damage. Complete alignment of the caliper piston should be achieved by pressing it gently into the bore with uniform pressure.

How to properly bleed a brake caliper using DOT 3 or DOT 4 brake fluid on Mercury Sable?

Only approved DOT 3 or DOT 4 brake fluid should be used for bleeding a brake caliper because alternative fluids will permanently damage brake components and shut down the brakes. Brake fluid requires careful handling because it should not enter the eyes and proper hand washing must follow fluid exposure. Eye contact requires running water flushing for 15 minutes with necessary medical help for continued irritation. Drinking water followed by vomiting induction leads to immediate medical attention in case of fluid entering the mouth or stomach. Delegate immediate attention to brake fluid cleanup from painted or plastic surfaces because such fluid damages these materials. The bleeding process requires constant filling of the master cylinder reservoir with brake fluid from the specified type and prohibits the use of refilled fluid. You only need to bleed the brake system when disconnecting both the disc brake caliper along with other caliper components. A box end wrench should be used on the disc brake caliper bleeder screw while you attach a rubber drain tube which you should extend into clean brake fluid-filled container. An assistant should pump the brake pedal before maintaining constant force on it. The bleeder screw should be loosened while an assistant keeps pressure on the brake pedal then the screw should be tightened after a brake fluid stream appears as the assistant maintains pressure. Bleed the brakes through the bleeder screws while testing for bubble-free fluid until you achieve transparency in the reservoir then exchange fluid as required. Conclude by giving one additional torque to the disc brake caliper bleeder screw.

OEM Mercury Sable Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Brake Calipers found

View related parts
Mercury Sable Caliper Assembly, Rear Driver Side Part Number: 1F1Z-2553-BA
$85.93 MSRP: $114.07
You Save: $28.14 (25%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Caliper; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: LH Less pads, 4 wheel disc
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-2005 Mercury Sable | G, GS, LS, LS Premium, LTS, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Caliper, Front Driver Side Part Number: 4F1Z-2B121-AA
$45.79 MSRP: $66.65
You Save: $20.86 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Left; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: LH - with pads & bracket. 1 kit required per vehicle (to be used for R.H. and L.H. calipers), After 4-26-2004
- Position: Front Driver Side
- Replaced by: 1U2Z-2V001-JA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Caliper, Front Driver Side Part Number: 5F9Z-2B121-BA
$85.58 MSRP: $118.39
You Save: $32.81 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Caliper, Front Passenger Side Part Number: 5F9Z-2B120-BA
$85.58 MSRP: $118.39
You Save: $32.81 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Caliper Assembly, Rear Passenger Side Part Number: 1F1Z-2552-BA
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Caliper; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: RH Less pads, 4 wheel disc
- Position: Rear Passenger Side
- Replaces: 1F1Z-2552-AA, F8DZ-2552-AA, YF3Z-2552-AA, YF1Z-2552-AA, XF1Z-2552-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-2005 Mercury Sable | G, GS, LS, LS Premium, LTS, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Caliper, Front Passenger Side Part Number: F4DZ-2B120-AA
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-2000 Mercury Sable | G, GS, LS, LS Premium, LTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Caliper, Front Driver Side Part Number: 4F1Z-2B121-BA
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: LH - less pads, includes bracket. 1 kit required per vehicle (to be used for R.H. and L.H. calipers), After 4-26-2004
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Caliper Overhaul Kit Part Number: F3OY-2221-A
Product Specifications
- Other Name: Kit - Caliper Repair; Brake Caliper Repair Kit; Disc Brake Hardware Kit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Caliper, Rear Driver Side Part Number: 8G1Z-2553-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Driver Side
- Replaced by: 6F9Z-2553-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Caliper, Passenger Side Part Number: E9OY-2V120-BRM
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1992 Mercury Sable | GS, LS | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Caliper, Driver Side Part Number: E9OY-2V121-BRM
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1992 Mercury Sable | GS, LS | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Caliper, Passenger Side Part Number: F3DZ-2V120-BRM
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Manufacturer Note: RH - Motorcraft Reman - less pads, except SHO
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993 Mercury Sable | GS, LS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Caliper, Driver Side Part Number: F3DZ-2V121-BRM
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Manufacturer Note: LH - Motorcraft Reman - less pads, except SHO
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993 Mercury Sable | GS, LS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Caliper, Front Driver Side Part Number: F4DZ-2B121-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: LH, exc. PC
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-2000 Mercury Sable | G, GS, LS, LS Premium, LTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Caliper, Rear Passenger Side Part Number: 8G1Z-2552-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Passenger Side
- Replaced by: 6F9Z-2552-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Caliper, Rear Passenger Side Part Number: 2F1Z-2552-AA
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH - With pads, 4 wheel disc
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Caliper, Passenger Side Part Number: 2F1Z-2B120-AA
Product Specifications
- Other Name: Caliper With Pads; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH - with pads. 1 kit required per vehicle (to be used for R.H. and L.H. calipers)
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Caliper, Front Passenger Side Part Number: 1F1Z-2B120-AA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH With pads 1 kit required per vehicle (to be used for R.H. and L.H. calipers)
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Caliper, Front Driver Side Part Number: 1F1Z-2B121-AA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: LH With pads. 1 kit required per vehicle (to be used for R.H. and L.H. calipers)
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Caliper, Rear Driver Side Part Number: 2F1Z-2553-AA
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: LH - With pads, 4 wheel disc
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

| Page 1 of 2 |Next >

1-20 of 24 Results

Mercury Sable Brake Caliper

OEM Brake Caliper boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Caliper with long life and a perfect fit. Come to our website and find genuine Mercury Sable parts. We keep a wide inventory of OEM Sable parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Mercury Sable Brake Caliper is used in Mercury Sable vehicles; these are among the prime vehicles known for their reliability and performance when it comes to braking system. This Brake Caliper efficiently translates hydraulic pressure received from the master cylinder into mechanical force which clamps the brake pads on to the rotors making safe and efficient stopping possible. The use of fixed and floating calipers is normally found in Mercury Sable models where the fixed type apply force through a number of pistons to have equal force while the floating type apply force through a single piston that is situated in the center and moves to ensure equal force. Mercury Sable Brake Caliper also changed with time, with options that include those for regular cars and those that are performance tuned to give enhanced braking by using materials such as aluminum. This versatility not only enhances the operations of the Mercury Sable but also raises considerably the safety levels on the road. Examining and carrying out proper maintenance to the Brake Caliper will help in avoiding problems like unequal wear so the Mercury Sable will run as excellent as before. That it has been incorporated in different versions of the Sable vehicle over the years of its manufacturing is a testimony to the indispensability of the Brake Caliper in sustaining the worth of the vehicle. Likewise, the Mercury Sable Brake Caliper enjoys the non-cutesy and non-fancy type of marketing in the automotive market because it was greatly engineered for the auto market as one of the best safety tools for car drivers. All in all, the Mercury Sable Brake Caliper is one of the finest examples of brand's dedication to delivering only the best products to the car enthusiasts.

Mercury Sable Brake Caliper Parts and Q&A

Caliper, Front Passenger Side
4F1Z-2B120-BA
Q: How to service and repair the front brake caliper on Mercury Sable?
A:
Service and repair operations of the front brake caliper require beginning with fluid drainage followed by using only DOT 3 or DOT 4 brake fluid to protect brake components from permanent damage. When handling brake fluid users should protect their eyes and wash their hands completely after completion. If eyes come into contact with brake fluid users need to flush them with water for 15 minutes and obtain medical help if signs of irritation appear. Ingesting brake fluid requires you to drink water followed by vomiting induction then you should get medical attention immediately. Beware of brake fluid spills on painted surfaces and plastic constituents since rapid water cleaning will protect them. The disc brake caliper needs to be secured inside a vise before removing its piston through the mechanism of a wood block placed between the caliper bridge and piston then low air pressure applied to the fluid port to push out the piston. Discard the seals together with dust boots when removing the piston and refrain from honing caliper bores due to unavailability of piston-specific calipers. A front disc brake caliper replacement is necessary when you detect bores damage or when leaks prevent proper sealing. For assembling the calipers install new dust boots together with piston seals and replace the brake fluid with DOT 3 or DOT 4 according to Ford specification SAE J1704. High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or a DOT 3 equivalent matching Ford specification ESA-M6C25-A should be used to lubricate both the piston dust boot and piston seal in addition to the caliper piston and caliper bore. Use this fluid when assembling the caliper piston seal and dust boot with caution to prevent damage. Complete alignment of the caliper piston should be achieved by pressing it gently into the bore with uniform pressure.
Caliper Assembly, Rear Driver Side
1F1Z-2553-BA
Q: How to properly bleed a brake caliper using DOT 3 or DOT 4 brake fluid on Mercury Sable?
A:
Only approved DOT 3 or DOT 4 brake fluid should be used for bleeding a brake caliper because alternative fluids will permanently damage brake components and shut down the brakes. Brake fluid requires careful handling because it should not enter the eyes and proper hand washing must follow fluid exposure. Eye contact requires running water flushing for 15 minutes with necessary medical help for continued irritation. Drinking water followed by vomiting induction leads to immediate medical attention in case of fluid entering the mouth or stomach. Delegate immediate attention to brake fluid cleanup from painted or plastic surfaces because such fluid damages these materials. The bleeding process requires constant filling of the master cylinder reservoir with brake fluid from the specified type and prohibits the use of refilled fluid. You only need to bleed the brake system when disconnecting both the disc brake caliper along with other caliper components. A box end wrench should be used on the disc brake caliper bleeder screw while you attach a rubber drain tube which you should extend into clean brake fluid-filled container. An assistant should pump the brake pedal before maintaining constant force on it. The bleeder screw should be loosened while an assistant keeps pressure on the brake pedal then the screw should be tightened after a brake fluid stream appears as the assistant maintains pressure. Bleed the brakes through the bleeder screws while testing for bubble-free fluid until you achieve transparency in the reservoir then exchange fluid as required. Conclude by giving one additional torque to the disc brake caliper bleeder screw.