How to remove and replace the front bumper cover on Mercury Sable?

You must place the vehicle into neutral gear while it sits on a hoist before starting the front bumper cover removal process of a Taurus or Sable vehicle. Andy should extract the two front bumper cover scrivets together with the two front bumper cover bolts before tightening them to 6 Nm (53 lb-in) when reinserting these components. The six front bumper cover wheel house screws need removal while installation requires screw torque of 2 Nm (18 lb-in). The replacement of the front bumper cover on Taurus and Sable requires the removal of four bolts under the bumper cover front section as well as separation of the fog lamps and front side marker lamps electrical connectors. Unclip the front of the bumper cover by pulling it outward before conducting complete removal of the cover. Before reinstalling the bumper cover examine the mounting reinforcements to check for damage and perform replacement when needed. The installation of the bumper cover requires a step-by-step reverse procedure of what was used for removal.

How to service the rear bumper cover on a wagon on Mercury Sable?

Service of the wagon's rear bumper cover begins with taking out the load space trim panel. You should begin by removing the LH rear bumper cover to rear quarter panel nuts then progress to removing the RH rear bumper cover panel nuts followed by the rear bumper cover nuts. Support the raised vehicle afterward you should remove splash shield screws then set aside both LH and RH splash shields to access the rear bumper cover attachment bolts. Begin by disconnecting the drain tube followed by removing the two rear bumper cover to rear quarter panel nuts and the pin-type retainers. The rear bumper cover installation requires separating the connector tied to the rear side marker light while removing the screws until the cover fully detaches from the body. When installing the new cover reverse all the steps used during removal.

OEM Mercury Sable Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Bumpers found

View related parts
Mercury Sable Impact Bar, Rear Part Number: YF1Z-17906-AB
$63.01 MSRP: $85.75
You Save: $22.74 (27%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Impact Bar, Rear; Bar
- Manufacturer Note: Steel
- Position: Rear
- Replaces: XF1Z-17906-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Bumper Cover, Front Part Number: 4F4Z-17D957-BA
$246.40 MSRP: $338.07
You Save: $91.67 (28%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front
- Manufacturer Note: Paint to match
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Bumper Cover Part Number: 2F4Z-17K835-BA
$259.55 MSRP: $356.10
You Save: $96.55 (28%)
ADD TO CART
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
- Replaces: YF4Z-17K835-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2003 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Bumper Cover Part Number: 4F4Z-17K835-BA
$374.54 MSRP: $518.14
You Save: $143.60 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Impact Bar, Front Part Number: 1F1Z-17757-AA
$88.99 MSRP: $123.11
You Save: $34.12 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Impact Bar, Front; Bar
- Position: Front
- Replaces: YF1Z-17757-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2005 Mercury Sable | G, GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Bumper Cover, Front Part Number: 8T5Z-17D957-AAPTM
$574.43 MSRP: $716.33
You Save: $141.90 (20%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front
- Manufacturer Note: Paint to match
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Impact Bar, Rear Part Number: 8G1Z-17906-B
$132.65 MSRP: $193.08
You Save: $60.43 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Impact Bar, Rear
- Position: Rear
- Replaces: 6G1Z-17906-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Impact Bar, Rear Part Number: YF1Z-17906-BA
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Impact Bar, Rear; Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2005 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Bumper Cover Part Number: F8DZ-17K835-AA
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Bumper Cover Part Number: F6DZ-17K835-B
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Bumper Cover Part Number: 8T5Z-17K835-CAPTM
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Bumper Cover Part Number: 8T5Z-17K835-AAPTM
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Impact Bar, Front Part Number: 8G1Z-17757-A
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Impact Bar, Front
- Position: Front
- Replaces: 5G1Z-17757-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Bumper Cover, Front Part Number: 2F4Z-17D957-CA
Product Specifications
- Other Name: Bumper Assembly - Front
- Manufacturer Note: Paint to match
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2003 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Bumper Cover, Rear Part Number: 2F1Z-17K835-DA
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Replaces: YF1Z-17K835-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

Mercury Sable Bumper

OEM Bumper boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Bumper with long life and a perfect fit. Come to our website and find genuine Mercury Sable parts. We keep a wide inventory of OEM Sable parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Mercury Sable Bumper stands out as a reliable system because it protects essential safety components alongside the body during hit-and-run situations. Through time the Mercury Sable Bumper underwent substantial transformation as designers replaced initial metal bars with contemporary reinforcement bars protected by advanced plastic materials thus achieving better performance with superior characteristics. The 1970s federal regulations promoting crash damage cost reduction led automobile manufacturers to create robust bumper designs through which the Mercury Sable Bumper evolved. Owners who possess multiple Sable models can select the Mercury Sable Bumper for complete vehicle safety maintenance across their Generation range. Built from aluminum and stainless steel and carbon steel materials the Mercury model Bumper performs well while improving vehicle safety by taking in impact forces. The car component excels through its aerodynamic shape combined with built-in lighting options which give it market distinction along with helpful functionality. The car depends on its part for both safety performance and reliability which establishes this vehicle as a dependable middle-class sedan solution.

Mercury Sable Bumper Parts and Q&A

Bumper Cover, Front
8T5Z-17D957-AAPTM
Q: How to remove and replace the front bumper cover on Mercury Sable?
A:
You must place the vehicle into neutral gear while it sits on a hoist before starting the front bumper cover removal process of a Taurus or Sable vehicle. Andy should extract the two front bumper cover scrivets together with the two front bumper cover bolts before tightening them to 6 Nm (53 lb-in) when reinserting these components. The six front bumper cover wheel house screws need removal while installation requires screw torque of 2 Nm (18 lb-in). The replacement of the front bumper cover on Taurus and Sable requires the removal of four bolts under the bumper cover front section as well as separation of the fog lamps and front side marker lamps electrical connectors. Unclip the front of the bumper cover by pulling it outward before conducting complete removal of the cover. Before reinstalling the bumper cover examine the mounting reinforcements to check for damage and perform replacement when needed. The installation of the bumper cover requires a step-by-step reverse procedure of what was used for removal.
Impact Bar, Rear
YF1Z-17906-BA
Q: How to service the rear bumper cover on a wagon on Mercury Sable?
A:
Service of the wagon's rear bumper cover begins with taking out the load space trim panel. You should begin by removing the LH rear bumper cover to rear quarter panel nuts then progress to removing the RH rear bumper cover panel nuts followed by the rear bumper cover nuts. Support the raised vehicle afterward you should remove splash shield screws then set aside both LH and RH splash shields to access the rear bumper cover attachment bolts. Begin by disconnecting the drain tube followed by removing the two rear bumper cover to rear quarter panel nuts and the pin-type retainers. The rear bumper cover installation requires separating the connector tied to the rear side marker light while removing the screws until the cover fully detaches from the body. When installing the new cover reverse all the steps used during removal.