How should one safely service the fuel level sensor to prevent personal injury and ensure proper installation on Mercury Sable?

The fuel level sensor service requires safety precautions by staying away from both smoking and carrying lighted tobacco products and keeping flames away from fuel components since these materials can ignite flammable mixtures that can result in severe personal injury. Service staff must withdraw all personal electronic devices from the work area. Relieve fuel system pressure before disconnecting any fuel tubing equipment because the system maintains high pressure after engine shutdown. Disconnection of the battery ground cable should always occur during maintenance of both EVAP system and fuel-related components. Engineers can service the fuel level sensor due to its replaceable fuel level sender feature. First elevate the vehicle to a hoist and set its position to neutral and afterwards drain the fuel system pressure and unplug the battery ground wire. The fuel tank filler cap needs to be turned counterclockwise until it disengages however removing it during tank fullness will leak out approximately one-eighth of the fuel. Feed the dripping hose tube into the fuel tank filler pipe while the fitting directs down to the fuel tank spout opening for draining the fuel out. The Fuel Storage Tanker must be attached to the hose to empty fuel until the sensor mounting flange remains below the fuel level. Taurus and Sable model owners should remove their rear seat lower cushions after Sable owners must raise the load floor while releasing the two floor support brackets. Remove the fuel level sensor access cover then clean both the sensor connections together with their surrounding area before disconnecting the electrical connector. The area around the work should receive several pieces of absorbent toweling to collect any leaking fuel. You should handle the Fuel Tank Sender Unit Wrench gently to protect the sensor during lock ring removal because this step leads to lifting the sensor from the tank and unfastening the quick connect coupling. You must eliminate the old O-ring before applying fresh engine oil to the new one which will go into the installation. The installation process requires using both a new lock ring and O-ring seal for which you must guide the arrows between the sensor and tank to match before clamping the lock ring at the stop tabs.

OEM Mercury Sable Fuel Level Sensor

Gas Gauge Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Fuel Level Sensors found

View related parts
Mercury Sable Fuel Sending Unit Part Number: 1F1Z-9275-BA
$169.13 MSRP: $233.98
You Save: $64.85 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit; Fuel Level Sensor; Sending Unit
- Manufacturer Note: Flex Fuel Ethanol, FROM 4/8/2001
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005, 2001 Mercury Sable | LS
View related parts
Mercury Sable Fuel Pump Part Number: F4DZ-9H307-BB
$93.51 MSRP: $129.36
You Save: $35.85 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump Module; Fuel Tank Sending Unit; Electric Fuel Pump; Fuel Level Sensor.; Gauge Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1995 Mercury Sable | GS, LS, LTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Sable Fuel Sending Unit Part Number: 6F1Z-9275-A
$210.24 MSRP: $290.84
You Save: $80.60 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit; Fuel Level Sensor; Sending Unit
- Replaces: 1F1Z-9275-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Fuel Gauge Sending Unit Part Number: 8G1Z-9A299-B
$16.60 MSRP: $22.59
You Save: $5.99 (27%)
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit, Right; Fuel Level Sensor; Fuel Sending Unit; Level Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Fuel Gauge Sending Unit Part Number: 8G1Z-9A299-G
$40.53 MSRP: $64.36
You Save: $23.83 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit; Fuel Level Sensor; Fuel Sending Unit; Level Sensor
- Replaces: 8G1Z-9A299-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Fuel Gauge Sending Unit, Passenger Side Part Number: 8G1Z-9A299-A
$19.35 MSRP: $30.73
You Save: $11.38 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Tank Sending Unit, Left, Right; Fuel Level Sensor; Fuel Sending Unit; Level Sensor; Fuel Sender Unit
- Manufacturer Note: Sender For 9H307 Fuel Pump
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Fuel Pump, Passenger Side Part Number: 8G1Z-9275-A
$65.61 MSRP: $104.18
You Save: $38.57 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Electric Fuel Pump, Right; Fuel Transfer Unit; Fuel Level Sensor; Fuel Sending Unit; Fuel Sender Unit
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Fuel Sending Unit Part Number: YF1Z-9275-AA
Product Specifications
- Other Name: Sender Assembly; Fuel Level Sensor; Sending Unit
- Manufacturer Note: 16 gallon tank
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Fuel Sending Unit Part Number: F7DZ9275CA
Product Specifications
- Other Name: Sender Assembly; Fuel Level Sensor; Sending Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Fuel Sending Unit Part Number: F7DZ-9275-AA
Product Specifications
- Other Name: Sender Assembly; Fuel Level Sensor; Sending Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1999 Mercury Sable | G, GS, LS, LS Premium | 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Fuel Sending Unit Part Number: YF1Z-9275-BA
Product Specifications
- Other Name: Sender Assembly; Fuel Level Sensor
- Manufacturer Note: 18 gallon tank , BEFORE 2/5/2001
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2001 Mercury Sable | GS, LS, LS Premium | 6 Cyl 3.0 L GAS

Mercury Sable Fuel Level Sensor

OEM Fuel Level Sensor boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Fuel Level Sensor with long life and a perfect fit. Come to our website and find genuine Mercury Sable parts. We keep a wide inventory of OEM Sable parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Mercury Sable Fuel Level Sensor is the key component through which shows the efficiency and durability of the car in auto market. Its function is to detect the amount of fuel remaining in the tank and inform the driver about it, so that the car is not operated to a extent that it runs out of fuel; the information is also useful in optimising the performance of the car in terms of fuel consumption. Mercury Sable Fuel Level Sensor is ideal for high temperature service since it has complex and compact construction involving a float, the actuating rod and the resistor to offer the correct reading as it draws power current in minimal level. This reliability is for several Sable models since inconsistencies cause prolonged indication of the full tank, boosting safety issues on the road. Being part of the Ford's lineup as a division that was shut down, the Mercury Sable is a mid-size sedan that has evolved through five generations, and where each generation got progressive performance enhancements, the Fuel Level Sensor has been central to the sedan's design. The fact that the sensor developed can accommodate different Sable models makes it unique, not forgetting that the ability of the sensor to generate real-time data makes the vehicle efficient. More specifically, the Mercury Sable Fuel Level Sensor remains one of the main attractions of the automotive market thanks to its corrosion and wear resistant structure with maximum precision to give a driver a perfect grip on the fuel gauge. In summary, having the Mercury Sable Fuel Level Sensor delivers much needed reliability, protection, and power to the status of an automobiles and therefore, it is invaluable to have it especially for the owners of the Mercury Sable.

Mercury Sable Fuel Level Sensor Parts and Q&A

Fuel Pump, Passenger Side
8G1Z-9275-A
Q: How should one safely service the fuel level sensor to prevent personal injury and ensure proper installation on Mercury Sable?
A:
The fuel level sensor service requires safety precautions by staying away from both smoking and carrying lighted tobacco products and keeping flames away from fuel components since these materials can ignite flammable mixtures that can result in severe personal injury. Service staff must withdraw all personal electronic devices from the work area. Relieve fuel system pressure before disconnecting any fuel tubing equipment because the system maintains high pressure after engine shutdown. Disconnection of the battery ground cable should always occur during maintenance of both EVAP system and fuel-related components. Engineers can service the fuel level sensor due to its replaceable fuel level sender feature. First elevate the vehicle to a hoist and set its position to neutral and afterwards drain the fuel system pressure and unplug the battery ground wire. The fuel tank filler cap needs to be turned counterclockwise until it disengages however removing it during tank fullness will leak out approximately one-eighth of the fuel. Feed the dripping hose tube into the fuel tank filler pipe while the fitting directs down to the fuel tank spout opening for draining the fuel out. The Fuel Storage Tanker must be attached to the hose to empty fuel until the sensor mounting flange remains below the fuel level. Taurus and Sable model owners should remove their rear seat lower cushions after Sable owners must raise the load floor while releasing the two floor support brackets. Remove the fuel level sensor access cover then clean both the sensor connections together with their surrounding area before disconnecting the electrical connector. The area around the work should receive several pieces of absorbent toweling to collect any leaking fuel. You should handle the Fuel Tank Sender Unit Wrench gently to protect the sensor during lock ring removal because this step leads to lifting the sensor from the tank and unfastening the quick connect coupling. You must eliminate the old O-ring before applying fresh engine oil to the new one which will go into the installation. The installation process requires using both a new lock ring and O-ring seal for which you must guide the arrows between the sensor and tank to match before clamping the lock ring at the stop tabs.