Ford 7L8Z-17664-A
Washer Pump

Service of the windshield washer pump begins with removing the windshield washer reservoir first. The first step requires you to remove the washer pump combined with its rubber seal. The installation procedure should be conducted by reversing the steps used for removal.

The windshield washer pump service starts with disassembly of the right-hand front wheel and tire then the right-hand front splash shield. Proper drainage of the windshield washer reservoir is necessary to avoid fluid spilling because the washer solution includes harmful methanol which must be handled according to label cautions. First cut the power connection apart from the washer pump hose and break the pump loose from its mounting position. Install the windshield washer pump only when the washer reservoir contains fluid to prevent equipment damage. First reverse the removal process while inserting Ultra-Clear Windshield Washer Concentrate C9AZ-19550-AC or BC or an equivalent which complies with Ford specification ESR-M17P5-A.

Service of the windshield washer pump along with the reservoir of the front coupe starts with disconnecting the battery ground cable. The windshield washer reservoir can be detached by removing its nuts then pulling it directly upwards. The technician should disconnect both electrical items and hose from the windshield washer pump before draining the windshield washer solvent into a clean container. Pull the windshield washer pump from its reservoir before taking away the pump-to-reservoir seal to be disposed of when the seal exhibits signs of damage or wear. You should avoid power up the windshield washer pump until you fill the reservoir to capacity. The vehicle needs 16 kilometers (10 miles) of driving after battery connection/disconnection since it must relearn its adaptive strategy resulting in possible abnormal drive symptoms. The installer should perform the reverse steps used for removal to finish the process.

Service of the windshield washer pump begins with removing the windshield washer reservoir first. The first step requires you to remove the washer pump combined with its rubber seal. The installation procedure should be conducted by reversing the steps used for removal.

Service of the rear window washer pump begins with placing the vehicle on a hoist in NEUTRAL position before removing the RH front fender splash shield. The windshield washer solution contains poison risk due to methanol so use caution according to safety alerts on the label to prevent injury. Draining the windshield washer reservoir entirely should be your first step before washer pump removal to avoid fluid leakage. Separate the electrical connector along with the hose before pulling out the rear window washer pump carefully to prevent damaging the rubber grommet. To complete the process reinstall all components before putting washer fluid into the fluid reservoir. One must never activate the washer pump until the reservoir has sufficient fluid inside since early pump failure may occur.

Service and repair of the windshield washer pump starts with placing the vehicle on a hoist set to NEUTRAL position followed by splash shield removal from the right-hand front fender. Wear caution when using the windshield washer solution since methanol is poisonous and read all safety warnings on the container label to protect yourself. Discharging the windshield washer fluid from the reservoir is essential to avoid spills before pump replacement. Drop the windshield washer pump after you disconnect its electrical connector and hose yet be mindful to protect the rubber grommet from damage. The windshield washer reservoir must receive washer fluid before operating the pump because emptying it may damage the pump.

Fill the reservoir with Ultra-Clear Windshield Washer Concentrate C9AZ-19550-AC or BC, or an equivalent that meets Ford specification ESR-M17P5-A.

Reverse the removal steps and fill the windshield washer reservoir with windshield washer fluid.

Remove the bolts securing the reservoir and set it aside.

Reverse the removal procedure.

Disconnect the battery ground cable and the engine sub-harness electrical connectors.

Remove the right-hand front wheel and tire assembly, followed by the right-hand front splash shield.

To prevent spilling washer fluid, which contains methanol and is poisonous.

Pry the windshield washer pump from the reservoir and discard the pump to reservoir seal if it shows any signs of wear.

Reverse the removal steps and fill the windshield washer reservoir with windshield washer fluid.

Operating the pump before the reservoir is filled may lead to premature pump failure.