How to service and repair the fuel filler hose on 2000 Ford Focus?

Service and repair operations for the fuel filler hose should start with disconnecting the battery ground cable and loosening right-hand rear wheel nuts. Start by removing the fuel filler cap followed by vehicle lift and support. After that uninstall the right-hand rear wheel together with the splash shield. Properly bend the fuel tank vent pipes and filler pipe by avoiding damage from sharp tools while performing this step. Remember the original location of the retaining clamp together with the clip because you will need it for reinstalling. The next step requires disconnecting the tube that runs to the canister vent solenoid while keeping the solenoid free from damage. You must disconnect the fuel filler pipe after unbolted its two anchoring points. To reinstall the system follow the opposite steps of the removal procedure while setting the fuel filler and vent pipe retaining clamp and clips in their original positions. Run an evaporative emission system leak test as the last step to validate proper system functionality.

OEM 2000 Ford Focus Fuel Filler Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Fuel Filler Hoses found

View related parts
2000 Ford Focus Filler Neck Part Number: 2M5Z-9034-CA
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Manufacturer Note: 4 Door Wagon
- Replaces: YS4Z-9034-HA
- Base No.: 9032
- Item Weight: 7.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2M5Z-9034-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford Focus Submodels:
- SE, ZTW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
2000 Ford Focus Filler Neck Part Number: 2M5Z-9034-BA
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Manufacturer Note: 4 Door Sedan
- Replaces: YS4Z-9034-GA
- Base No.: 9034
- Item Weight: 1.80 Pounds
- Item Dimensions: 30.9 x 5.8 x 11.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2M5Z-9034-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford Focus Submodels:
- LX, SE, Sony Limited Edition, ZTS | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
2000 Ford Focus Filler Neck Part Number: 2M5Z-9034-AA
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Manufacturer Note: Pipe asy - fuel filler, 3 door and 5 door sedan
- Replaces: YS4Z-9034-AA
- Base No.: 9034
- Item Weight: 1.80 Pounds
- Item Dimensions: 30.9 x 6.0 x 11.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2M5Z-9034-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford Focus Submodels:
- SVT, ZX3, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS

2000 Ford Focus Fuel Filler Hose

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2000 Ford Focus Fuel Filler Hose available at FordPartsDeal.com. You can confidently purchase our OEM 2000 Ford Focus Fuel Filler Hose as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2000 Ford Focus Fuel Filler Hose Parts Q&A

Q: How to service and repair the fuel filler hose on 2000 Ford Focus?
A: Service and repair operations for the fuel filler hose should start with disconnecting the battery ground cable and loosening right-hand rear wheel nuts. Start by removing the fuel filler cap followed by vehicle lift and support. After that uninstall the right-hand rear wheel together with the splash shield. Properly bend the fuel tank vent pipes and filler pipe by avoiding damage from sharp tools while performing this step. Remember the original location of the retaining clamp together with the clip because you will need it for reinstalling. The next step requires disconnecting the tube that runs to the canister vent solenoid while keeping the solenoid free from damage. You must disconnect the fuel filler pipe after unbolted its two anchoring points. To reinstall the system follow the opposite steps of the removal procedure while setting the fuel filler and vent pipe retaining clamp and clips in their original positions. Run an evaporative emission system leak test as the last step to validate proper system functionality.