How to service and repair the fuel filler hose on 2001 Ford Focus?

A fuel filler hose service or repair begins with grounding the battery while also loosening right-hand rear wheel nuts. To access the fuel filler hose you should first remove the fuel filler cap and then lift your vehicle while supporting it with proper equipment to unbolt the right-hand rear wheel and its splash shield. Disconnect the fuel tank vent pipes as well as the filler pipe while using caution to prevent damage to the pipes through the use of sharp implements. Senator the original placement of the retaining clamp and the clip because it will help reattach them accurately. The technician disconnects the canister vent solenoid tube while paying attention to avoid damaging the solenoid component. Unfasten the two bolts from the fuel filler pipe for removal. To install the components follow the opposite sequence of the removal steps while placing the fuel filler and vent pipe retaining clamp and clips back in their original positions. An elapsed evaporative emission system leak check must be performed to verify correct system operation.

OEM 2001 Ford Focus Fuel Filler Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Fuel Filler Hoses found

View related parts
2001 Ford Focus Filler Neck Part Number: 2M5Z-9034-CA
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Manufacturer Note: 4 Door Wagon
- Replaces: YS4Z-9034-HA
- Base No.: 9032
- Item Weight: 7.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2M5Z-9034-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Focus Submodels:
- SE, ZTW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
2001 Ford Focus Filler Neck Part Number: 2M5Z-9034-BA
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Manufacturer Note: 4 Door Sedan
- Replaces: YS4Z-9034-GA
- Base No.: 9034
- Item Weight: 1.80 Pounds
- Item Dimensions: 30.9 x 5.8 x 11.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2M5Z-9034-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Focus Submodels:
- LX, SE, Sony Limited Edition, ZTS | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
2001 Ford Focus Filler Neck Part Number: 2M5Z-9034-AA
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Manufacturer Note: Pipe asy - fuel filler, 3 door and 5 door sedan
- Replaces: YS4Z-9034-AA
- Base No.: 9034
- Item Weight: 1.80 Pounds
- Item Dimensions: 30.9 x 6.0 x 11.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2M5Z-9034-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Focus Submodels:
- SVT, ZX3, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS

2001 Ford Focus Fuel Filler Hose

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2001 Ford Focus Fuel Filler Hose available at FordPartsDeal.com. You can confidently purchase our OEM 2001 Ford Focus Fuel Filler Hose as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2001 Ford Focus Fuel Filler Hose Parts Q&A

Q: How to service and repair the fuel filler hose on 2001 Ford Focus?
A: A fuel filler hose service or repair begins with grounding the battery while also loosening right-hand rear wheel nuts. To access the fuel filler hose you should first remove the fuel filler cap and then lift your vehicle while supporting it with proper equipment to unbolt the right-hand rear wheel and its splash shield. Disconnect the fuel tank vent pipes as well as the filler pipe while using caution to prevent damage to the pipes through the use of sharp implements. Senator the original placement of the retaining clamp and the clip because it will help reattach them accurately. The technician disconnects the canister vent solenoid tube while paying attention to avoid damaging the solenoid component. Unfasten the two bolts from the fuel filler pipe for removal. To install the components follow the opposite sequence of the removal steps while placing the fuel filler and vent pipe retaining clamp and clips back in their original positions. An elapsed evaporative emission system leak check must be performed to verify correct system operation.