How to service and repair the 8.8-inch ring gear axle shaft on 2002 Ford F-150?

The procedure to work on the 8.8-inch ring gear axle shaft begins with vehicle suspension followed by tire removal and subsequently differential housing cover bolt disarm. Lubricant drainage should go into a clean container before removing the differential housing cover through the removal of 10 bolts. Drum brake vehicles require removing the rear brake drums as disc brake vehicles need a disconnected caliper while suspending the disc brake wire until the brake disc can be taken out. The removal process starts with the differential pinion shaft when the lock bolt gets discarded and the shaft is extracted. You must exercise caution to safeguard the rubber O-rings inside the axle shaft grooves while removing U-washers together with both axle shafts. Apply grease to the wheel bearing oil seal lip and use the installed axle shafts while watching for potential damage to the U-washer rubber O-ring seals in their grooves. After placing each U-washer onto the button end section of axle shafts you should extend the shafts outward. The threads of the differential pinion shaft require threadlock coating when installing it unless new pins are available. Then align the shaft with case lock bolt hole before using new bolts to secure it. Vehicle rear brake systems need to be installed with either drum brake drums or disc brake components and calipers. Apply a fresh continuous bead of sealant on the differential housing cover during installation within 15 minutes because late application might require new sealant. Fit the differential housing cover and its 10 bolts before filling the rear axle housing with 2.37 liters (5 pints) of the recommended lubricating fluid. The last step entails cleaning all wheel hub surfaces before installing the tire wheel unit.

OEM 2002 Ford F-150 Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Axle Shafts found

View related parts
2002 Ford F-150 Axle Shaft, Rear Passenger Side Part Number: YL1Z-4234-CA
$282.20 MSRP: $390.39
You Save: $108.19 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Right; Axle Shafts
- Position: Rear Passenger Side
- Base No.: 4234
- Item Weight: 29.50 Pounds
- Item Dimensions: 40.8 x 8.3 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: YL1Z-4234-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Drive Axle, Front Passenger Side Part Number: 3L3Z-3219-AA
$111.66 MSRP: $154.46
You Save: $42.80 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Drive Axle Shaft, Front Right; Axle Shaft; Axle Shafts; Axle Assembly
- Position: Front Passenger Side
- Replaces: F65Z-3219-AA
- Item Weight: 9.00 Pounds
- Item Dimensions: 27.5 x 5.5 x 13.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3L3Z-3219-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Drive Axle, Front Driver Side Part Number: 2L3Z-3220-AB
$1128.78 MSRP: $1561.56
You Save: $432.78 (28%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Drive Axle Shaft, Front Left; Axle Shafts; Axle Assembly; Axle Shaft
- Position: Front Driver Side
- Replaces: F65Z-3220-AA
- Base No.: 3220
- Item Weight: 5.70 Pounds
- Item Dimensions: 9.1 x 8.1 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2L3Z-3220-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Lightning, Limited, Platinum, STX, SVT Raptor, THE 60TH ANNIVERSARY EDITION, XL, XLT | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L CNG, 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L LPG, 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L FLEX, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 6.2 L GAS
View related parts
2002 Ford F-150 Axle Shafts, Front Driver Side Part Number: 5L3Z-3B436-A
Product Specifications
- Other Name: Shaft - Front Axle; CV Axle Assembly, Front Left/Right; GSP CV Axle; CV Joint; Axle Assembly; Shaft & Joint Assembly
- Position: Front Driver Side
- Replaces: 3L3Z-3B436-AA
- Base No.: 3B436
- Item Weight: 23.40 Pounds
- Item Dimensions: 7.6 x 6.4 x 26.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5L3Z-3B436-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Axle Shaft, Rear Driver Side Part Number: YL3Z-4234-CB
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Left; Axle Shafts
- Position: Rear Driver Side
- Item Weight: 26.30 Pounds
- Item Dimensions: 39.7 x 8.3 x 8.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: YL3Z-4234-CB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Axle Shaft, Rear Passenger Side Part Number: YL3Z-4234-CA
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Right; Axle Shafts
- Position: Rear Passenger Side
- Item Weight: 26.00 Pounds
- Item Dimensions: 39.3 x 8.5 x 8.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: YL3Z-4234-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Axle Shaft, Rear Driver Side Part Number: YL3Z-4234-BB
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Left; Axle Shafts
- Position: Rear Driver Side
- Item Weight: 22.10 Pounds
- Item Dimensions: 40.8 x 8.4 x 8.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: YL3Z-4234-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Axle Shaft, Rear Passenger Side Part Number: YL3Z-4234-BA
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Right; Axle Shafts
- Position: Rear Passenger Side
- Item Weight: 25.70 Pounds
- Item Dimensions: 39.7 x 8.3 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: YL3Z-4234-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Axle Shaft, Rear Driver Side Part Number: YL1Z-4234-CB
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; Drive Axle Shaft, Rear Left; Axle Shafts
- Position: Rear Driver Side
- Base No.: 4234
- Item Weight: 19.60 Pounds
- Item Dimensions: 40.8 x 8.3 x 8.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: YL1Z-4234-CB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS

2002 Ford F-150 Axle Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2002 Ford F-150 Axle Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2002 Ford F-150 Axle Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2002 Ford F-150 Axle Shaft Parts Q&A

Q: How to service and repair the 8.8-inch ring gear axle shaft on 2002 Ford F-150?
A: The procedure to work on the 8.8-inch ring gear axle shaft begins with vehicle suspension followed by tire removal and subsequently differential housing cover bolt disarm. Lubricant drainage should go into a clean container before removing the differential housing cover through the removal of 10 bolts. Drum brake vehicles require removing the rear brake drums as disc brake vehicles need a disconnected caliper while suspending the disc brake wire until the brake disc can be taken out. The removal process starts with the differential pinion shaft when the lock bolt gets discarded and the shaft is extracted. You must exercise caution to safeguard the rubber O-rings inside the axle shaft grooves while removing U-washers together with both axle shafts. Apply grease to the wheel bearing oil seal lip and use the installed axle shafts while watching for potential damage to the U-washer rubber O-ring seals in their grooves. After placing each U-washer onto the button end section of axle shafts you should extend the shafts outward. The threads of the differential pinion shaft require threadlock coating when installing it unless new pins are available. Then align the shaft with case lock bolt hole before using new bolts to secure it. Vehicle rear brake systems need to be installed with either drum brake drums or disc brake components and calipers. Apply a fresh continuous bead of sealant on the differential housing cover during installation within 15 minutes because late application might require new sealant. Fit the differential housing cover and its 10 bolts before filling the rear axle housing with 2.37 liters (5 pints) of the recommended lubricating fluid. The last step entails cleaning all wheel hub surfaces before installing the tire wheel unit.