How to service and repair the brake caliper on 2002 Ford Taurus?

Service and repair of the brake caliper requires one to drain all brake fluid from the disc brake caliper but only approved DOT 3 or DOT 4 brake fluid should be used to avoid permanent brake component damage. The eye irritants alongside surface-damaging polyglycol ethers and polyglycols contained in brake fluid require proper eye flushing with water for 15 minutes before seeking medical attention for persistent irritation. The caliper must be clamped down before removing its piston through inserting a wood block between the caliper bridge and piston then applying low air pressure to the caliper port. The procedure requires discard of piston seals and dust boots then skipping caliper bore honing since caliper pistons cannot be installed into honed calipers. To solve front disc brake caliper leaking problems select new caliper seal kits while front disc brake caliper replacement is needed when the caliper bores show damage. New piston seals combined with fresh dust boots need to be utilized during assembly before performing the bleeding process with DOT 3 or DOT 4 brake fluid which must fulfill Ford specification SAE 11704 in case DOT 3 is absent. High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or a DOT 3 equivalent meeting Ford specification ESA-M6C25-A should be used to lubricate the piston dust boot, piston seal, caliper piston and caliper bore. Post-lubrication install the caliper piston seal alongside dust boot while inserting the caliper piston into the caliper bore with gentle yet steady pressure to prevent cocking.

OEM 2002 Ford Taurus Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Calipers found

View related parts
2002 Ford Taurus Caliper Assembly, Rear Driver Side Part Number: 1F1Z-2553-BA
$85.93 MSRP: $114.07
You Save: $28.14 (25%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Caliper; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: LH Less pads, 4 wheel disc
- Position: Rear Driver Side
- Base No.: 2553
- Item Weight: 7.30 Pounds
- Item Dimensions: 5.1 x 7.7 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1F1Z-2553-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford Taurus Submodels:
- G, GL, LX, SE, SE Comfort, SEL, SES, SHO, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 3.4 L GAS
View related parts
2002 Ford Taurus Caliper, Passenger Side Part Number: 2F1Z-2B120-AA
$25.53 MSRP: $35.32
You Save: $9.79 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper With Pads; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH - with pads. 1 kit required per vehicle (to be used for R.H. and L.H. calipers)
- Position: Passenger Side
- Base No.: 2B120
- Item Weight: 14.40 Pounds
- Item Dimensions: 5.1 x 6.6 x 8.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2F1Z-2B120-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford Taurus Submodels:
- LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2002 Ford Taurus Caliper Assembly, Rear Passenger Side Part Number: 1F1Z-2552-BA
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Caliper; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: RH Less pads, 4 wheel disc
- Position: Rear Passenger Side
- Replaces: 1F1Z-2552-AA, F8DZ-2552-AA, YF3Z-2552-AA, YF1Z-2552-AA, XF1Z-2552-AA
- Base No.: 2552
- Item Weight: 8.40 Pounds
- Item Dimensions: 14.3 x 14.6 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1F1Z-2552-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford Taurus Submodels:
- G, GL, LX, SE, SE Comfort, SEL, SES, SHO, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 3.4 L GAS
View related parts
2002 Ford Taurus Caliper, Rear Passenger Side Part Number: 2F1Z-2552-AA
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH - With pads, 4 wheel disc
- Position: Rear Passenger Side
- Base No.: 2552
- Item Weight: 7.80 Pounds
- Item Dimensions: 3.6 x 5.5 x 6.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2F1Z-2552-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford Taurus Submodels:
- LX, SE, SE Comfort, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2002 Ford Taurus Caliper, Driver Side Part Number: 2F1Z-2B121-AA
Product Specifications
- Other Name: Caliper With Pads; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: LH - with pads. 1 kit required per vehicle (to be used for R.H. and L.H. calipers)
- Position: Driver Side
- Base No.: 2B121
- Item Weight: 15.00 Pounds
- Item Dimensions: 5.0 x 6.7 x 8.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2F1Z-2B121-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford Taurus Submodels:
- LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2002 Ford Taurus Caliper, Rear Driver Side Part Number: 2F1Z-2553-AA
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: LH - With pads, 4 wheel disc
- Position: Rear Driver Side
- Base No.: 2553
- Item Weight: 7.30 Pounds
- Item Dimensions: 4.8 x 6.9 x 8.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2F1Z-2553-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford Taurus Submodels:
- LX, SE, SE Comfort, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

2002 Ford Taurus Brake Caliper

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2002 Ford Taurus Brake Caliper available at FordPartsDeal.com. You can confidently purchase our OEM 2002 Ford Taurus Brake Caliper as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2002 Ford Taurus Brake Caliper Parts Q&A

Q: How to service and repair the brake caliper on 2002 Ford Taurus?
A: Service and repair of the brake caliper requires one to drain all brake fluid from the disc brake caliper but only approved DOT 3 or DOT 4 brake fluid should be used to avoid permanent brake component damage. The eye irritants alongside surface-damaging polyglycol ethers and polyglycols contained in brake fluid require proper eye flushing with water for 15 minutes before seeking medical attention for persistent irritation. The caliper must be clamped down before removing its piston through inserting a wood block between the caliper bridge and piston then applying low air pressure to the caliper port. The procedure requires discard of piston seals and dust boots then skipping caliper bore honing since caliper pistons cannot be installed into honed calipers. To solve front disc brake caliper leaking problems select new caliper seal kits while front disc brake caliper replacement is needed when the caliper bores show damage. New piston seals combined with fresh dust boots need to be utilized during assembly before performing the bleeding process with DOT 3 or DOT 4 brake fluid which must fulfill Ford specification SAE 11704 in case DOT 3 is absent. High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or a DOT 3 equivalent meeting Ford specification ESA-M6C25-A should be used to lubricate the piston dust boot, piston seal, caliper piston and caliper bore. Post-lubrication install the caliper piston seal alongside dust boot while inserting the caliper piston into the caliper bore with gentle yet steady pressure to prevent cocking.