How to properly bleed a brake caliper using DOT 3 or DOT 4 brake fluid on Ford Taurus?

The use of approved DOT 3 or DOT 4 brake fluid alone is essential for bleeding the brake caliper because any other fluid will bring permanent damage to the brakes which result in inoperative brakes. The handling of brake fluid must be done with safety in mind when a person should stay away from their eyes and should clean their hands completely after finishing work. When eye exposure occurs there should be immediate water flushing for 15 minutes before seeking medical help in case irritation does not subside. Consumption of the substance requires you to drink water and cause vomiting while consulting emergency medical services without delay. Stay alert regarding brake fluid risks because it might harm painted or plastic materials and rapid water cleaning addresses any fluid leakage. The bleeding process requires you to maintain specified brake fluid inside the master cylinder reservoir while also discarding all drained fluid. The brake system bleeding process should not be performed from start to finish when the disc brake caliper is the only disconnected component. The disc brake caliper bleeder screw requires a box end wrench and a rubber drain tube for bleeder operations. Place the wrench on the screw and connect the tube with its free end submerged in clean brake fluid. An assistant should both pump on the brake pedal while maintaining steady force. The bleeder screw that leads to a brake fluid stream should be loosened before the assistant maintains pedal pressure. Tighten the screw afterward. Perform repeated cycles until both fluid and bubbles dissolve fully while you to maintain proper brake fluid levels in the master cylinder reservoir. Complete the procedure by fastening the disc brake caliper bleeder screw tight.

How to service and repair the front brake caliper on Ford Taurus?

The brake caliper service process begins by removing brake pads followed by the brake caliper flow bolt while moving the brake hose to the side to discard the copper washers. Next, remove the brake caliper. The area between the brake caliper and brake pad needs cleaning with brake parts cleaner until you confirm all oil, grease, fluid, and other materials are removed since they can damage pad lining material. All brake pad kit devices should be installed on the brake caliper anchor plate with new brake pads as well as new spring clips. Mount the brake hose into position before installing the new brake caliper flow bolt along with its copper washers and tighten it to 30 Nm (22 lb-ft). Proper seat alignment of caliper pin boots will protect guide pins from damage during installation alongside maintaining correct brake hose orientation on the anchor plate. Screw and tighten the two caliper guide pin bolts at 60 Nm (44 lb-ft). Use steady force of 89-133 Nm (20-30 lb) on the brake pedal during one minute engine-operation to have brake pads grip the brake caliper. Conclude the process by testing brake function. Use only fresh brake fluid which matches manufacturer requirements since using previously drained fluid creates system contamination risks that can lead to personal injuries. Brake fluid should be washed off painted or plastic surfaces with water as soon as it appears. Consumers can obtain emergency medical data about Ford/Motorcraft vehicles by dialing 1-800-959-3673 while referring to the Material Safety Data Sheet (MSDS) when available for the specific product.

OEM Ford Taurus Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

38 Brake Calipers found

View related parts
Ford Taurus Caliper, Front Passenger Side Part Number: DG1Z-2B120-E
$78.62 MSRP: $127.64
You Save: $49.02 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front Passenger Side
- Replaces: DG1Z-2B120-B, BRCF-212
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Caliper, Front Driver Side Part Number: DG1Z-2B121-E
$97.55 MSRP: $162.00
You Save: $64.45 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front Driver Side
- Replaces: BRCF-213, DG1Z-2B121-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Caliper, Front Driver Side Part Number: 5F9Z-2B121-BA
$85.58 MSRP: $118.39
You Save: $32.81 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Caliper, Front Driver Side Part Number: DG1Z-2B121-A
$404.01 MSRP: $669.09
You Save: $265.08 (40%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Service Part May Differ From Production
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Caliper, Front Passenger Side Part Number: 5F9Z-2B120-BA
$85.58 MSRP: $118.39
You Save: $32.81 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Caliper, Black, Rear Driver Side Part Number: EG1Z-2553-C
$97.07 MSRP: $158.00
You Save: $60.93 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Brake Caliper
- Position: Rear Driver Side
- Replaces: EG1Z-2553-B, BRCF-305
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Caliper, Black, Rear Passenger Side Part Number: EG1Z-2552-C
$111.44 MSRP: $181.64
You Save: $70.20 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Brake Caliper
- Position: Rear Passenger Side
- Replaces: BRCF-304, EG1Z-2552-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Taurus Caliper Assembly, Rear Passenger Side Part Number: 1F1Z-2552-BA
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Caliper; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: RH Less pads, 4 wheel disc
- Position: Rear Passenger Side
- Replaces: 1F1Z-2552-AA, F8DZ-2552-AA, YF3Z-2552-AA, YF1Z-2552-AA, XF1Z-2552-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-2007 Ford Taurus | G, GL, LX, SE, SE Comfort, SEL, SES, SHO, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 3.4 L GAS
View related parts
Ford Taurus Caliper, Front Passenger Side Part Number: F4DZ-2B120-AA
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-2000 Ford Taurus | G, GL, LX, SE, SE Comfort, SEL, SES, SHO, SVG | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 3.4 L GAS
View related parts
Ford Taurus Caliper, Rear Passenger Side Part Number: 2F1Z-2552-AA
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH - With pads, 4 wheel disc
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2007 Ford Taurus | LX, SE, SE Comfort, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Passenger Side Part Number: 2F1Z-2B120-AA
Product Specifications
- Other Name: Caliper With Pads; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH - with pads. 1 kit required per vehicle (to be used for R.H. and L.H. calipers)
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford Taurus | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Front Passenger Side Part Number: 1F1Z-2B120-AA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH With pads 1 kit required per vehicle (to be used for R.H. and L.H. calipers)
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Taurus | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Front Driver Side Part Number: 1F1Z-2B121-AA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: LH With pads. 1 kit required per vehicle (to be used for R.H. and L.H. calipers)
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Taurus | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Rear Driver Side Part Number: 2F1Z-2553-AA
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: LH - With pads, 4 wheel disc
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2007 Ford Taurus | LX, SE, SE Comfort, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Driver Side Part Number: 2F1Z-2B121-AA
Product Specifications
- Other Name: Caliper With Pads; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: LH - with pads. 1 kit required per vehicle (to be used for R.H. and L.H. calipers)
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford Taurus | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Front Passenger Side Part Number: 3F1Z-2B120-BA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: RH - with pads & bracket. 1 kit required per vehicle (to be used for R.H. and L.H. calipers), Before 4-26-2004
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Taurus | LX, SE, SE Comfort, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Front Driver Side Part Number: 3F1Z-2B121-BA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: LH - with pads & bracket. 1 kit required per vehicle (to be used for R.H. and L.H. calipers), Before 4-26-2004
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Taurus | LX, SE, SE Comfort, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Front Passenger Side Part Number: 4F1Z-2B120-BA
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: RH - less pads, includes bracket. 1 kit required per vehicle (to be used for R.H. and L.H. calipers), After 4-26-2004
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Taurus | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Front Driver Side Part Number: 4F1Z-2B121-BA
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: LH - less pads, includes bracket. 1 kit required per vehicle (to be used for R.H. and L.H. calipers), After 4-26-2004
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Taurus | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Taurus Caliper, Rear Driver Side Part Number: 8G1Z-2553-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Driver Side
- Replaced by: 6F9Z-2553-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | Limited, SE, SEL | 6 Cyl 3.5 L GAS

| Page 1 of 2 |Next >

1-20 of 38 Results

Ford Taurus Brake Caliper

OEM Brake Caliper boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Caliper with long life and a perfect fit. Come to our website and find genuine Ford Taurus parts. We keep a wide inventory of OEM Taurus parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Brake Caliper in the Ford Taurus automobiles are imperative in the braking system of a car having the pistons to squeeze the brake pads on the rotors, which cause the friction leading to the halting of a car. These calipers come in two main types: spherical and barometric, sections include: fixed and floating. This type of caliper is rigid and comes with opposing pistons, while the other is mounted on the floating WhatsApp and parallel to the rotation axis of the disc; the floating calipers are likely to stick. Floating calipers, of which swinging calipers is one of the main subtypes, pivot inward when braking. Such materials as the plastic, aluminum or chrome plated steel are used in the pistons while fixed calipers are more complex as well as expensive but the perform well. Brake calipers are very important wear parts with significant impact on braking capability of Ford Taurus cars.

Ford Taurus Brake Caliper Parts and Q&A

Caliper Assembly, Rear Passenger Side
1F1Z-2552-BA
Q: How to properly bleed a brake caliper using DOT 3 or DOT 4 brake fluid on Ford Taurus?
A:
The use of approved DOT 3 or DOT 4 brake fluid alone is essential for bleeding the brake caliper because any other fluid will bring permanent damage to the brakes which result in inoperative brakes. The handling of brake fluid must be done with safety in mind when a person should stay away from their eyes and should clean their hands completely after finishing work. When eye exposure occurs there should be immediate water flushing for 15 minutes before seeking medical help in case irritation does not subside. Consumption of the substance requires you to drink water and cause vomiting while consulting emergency medical services without delay. Stay alert regarding brake fluid risks because it might harm painted or plastic materials and rapid water cleaning addresses any fluid leakage. The bleeding process requires you to maintain specified brake fluid inside the master cylinder reservoir while also discarding all drained fluid. The brake system bleeding process should not be performed from start to finish when the disc brake caliper is the only disconnected component. The disc brake caliper bleeder screw requires a box end wrench and a rubber drain tube for bleeder operations. Place the wrench on the screw and connect the tube with its free end submerged in clean brake fluid. An assistant should both pump on the brake pedal while maintaining steady force. The bleeder screw that leads to a brake fluid stream should be loosened before the assistant maintains pedal pressure. Tighten the screw afterward. Perform repeated cycles until both fluid and bubbles dissolve fully while you to maintain proper brake fluid levels in the master cylinder reservoir. Complete the procedure by fastening the disc brake caliper bleeder screw tight.
Caliper, Front Passenger Side
5F9Z-2B120-BA
Q: How to service and repair the front brake caliper on Ford Taurus?
A:
The brake caliper service process begins by removing Brake Pads followed by the brake caliper flow bolt while moving the brake hose to the side to discard the copper washers. Next, remove the brake caliper. The area between the brake caliper and brake pad needs cleaning with brake parts cleaner until you confirm all oil, grease, fluid, and other materials are removed since they can damage pad lining material. All brake pad kit devices should be installed on the brake caliper anchor plate with new brake pads as well as new spring clips. Mount the brake hose into position before installing the new brake caliper flow bolt along with its copper washers and tighten it to 30 Nm (22 lb-ft). Proper seat alignment of caliper pin boots will protect guide pins from damage during installation alongside maintaining correct brake hose orientation on the anchor plate. Screw and tighten the two caliper guide pin bolts at 60 Nm (44 lb-ft). Use steady force of 89-133 Nm (20-30 lb) on the brake pedal during one minute engine-operation to have brake pads grip the brake caliper. Conclude the process by testing brake function. Use only fresh brake fluid which matches manufacturer requirements since using previously drained fluid creates system contamination risks that can lead to personal injuries. Brake fluid should be washed off painted or plastic surfaces with water as soon as it appears. Consumers can obtain emergency medical data about Ford/Motorcraft vehicles by dialing 1-800-959-3673 while referring to the Material Safety Data Sheet (MSDS) when available for the specific product.