How to service and repair the rear brake caliper on 2006 Ford Crown Victoria?

First disable air suspension electrical power through the air suspension service switch OFF position to stop undesirable air spring inflation or deflation because this could move the vehicle position during service operations. You should depower the fire suppression system before starting maintenance on vehicles that have this equipment. Set the vehicle shift lever to NEUTRAL for hoisting the vehicle. Cut off the brake caliper flow bolt and detach the brake hose from the brake caliper by discarding the copper washers and plugging the hose. Guide pins along with guide pin boots require no removal unless there is a reason for suspicion since these components possess a permanent seal and lack repairability. First examine the brake caliper for leaks and binding slide pins while you remove its two bolts and caliper before proceeding to new caliper installation. Install the new caliper by placing its antirattle clips properly while replacing them if they show signs of wear or damage. Use the two caliper bolts to install the brake caliper you must tighten them to 25 Nm (18 ft. lbs.). After that, place the brake hose and install the brake caliper flow bolt with two new copper washers and tighten it to 50 Nm (37 ft. lbs.). The brake line needs clearing while fire suppressant systems require new power supplies. Before driving the vehicle, check correct operational status by applying the brakes multiple times while the service switch remains in the ON position if this feature applies to your vehicle.

OEM 2006 Ford Crown Victoria Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Calipers found

View related parts
2006 Ford Crown Victoria Caliper, Front Driver Side
Part Number: 7W7Z-2B121-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Front Driver Side
- Replaces: 6W7Z-2B121-AA, 3W1Z-2B121-AB, 3W7Z-2B121-AA, 6W1Z-2B121-AA
- Base No.: 2B120
- Item Weight: 11.80 Pounds
- Item Dimensions: 5.5 x 8.7 x 10.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7W7Z-2B121-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2006 Ford Crown Victoria Caliper, Front Passenger Side
Part Number: 7W7Z-2B120-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Front Passenger Side
- Replaces: 3W1Z-2B120-AB, 6W7Z-2B120-AA, 3W7Z-2B120-AA, 6W1Z-2B120-AA
- Base No.: 2B120
- Item Weight: 12.20 Pounds
- Item Dimensions: 5.7 x 8.6 x 10.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7W7Z-2B120-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2006 Ford Crown Victoria Caliper, Rear Driver Side
Part Number: 7W1Z-2553-B
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Driver Side
- Base No.: 2552
- Item Weight: 6.40 Pounds
- Item Dimensions: 5.3 x 6.2 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7W1Z-2553-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2006 Ford Crown Victoria Caliper, Rear Passenger Side
Part Number: 7W1Z-2552-B
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Passenger Side
- Base No.: 2552
- Item Weight: 6.70 Pounds
- Item Dimensions: 9.6 x 7.4 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7W1Z-2552-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2006 Ford Crown Victoria Caliper, Driver Side
Part Number: 6W7Z-2B121-AA
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pads; Brake Caliper Repair Kit; Brake Caliper
- Position: Driver Side
- Replaced by: 7W7Z-2B121-A
- Item Weight: 3.00 Pounds
- Item Dimensions: 5.4 x 6.5 x 8.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W7Z-2B121-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2006 Ford Crown Victoria Caliper, Passenger Side
Part Number: 6W7Z-2B120-AA
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pads; Brake Caliper Repair Kit; Brake Caliper
- Position: Passenger Side
- Replaced by: 7W7Z-2B120-A
- Item Weight: 3.00 Pounds
- Item Dimensions: 5.4 x 6.7 x 8.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W7Z-2B120-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Crown Victoria Submodels:
- Police Interceptor | 8 Cyl 4.6 L GAS

2006 Ford Crown Victoria Brake Caliper

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2006 Ford Crown Victoria Brake Caliper available at FordPartsDeal.com. You can confidently purchase our OEM 2006 Ford Crown Victoria Brake Caliper as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2006 Ford Crown Victoria Brake Caliper Parts Questions & Experts Answers

Q: How to service and repair the rear brake caliper on 2006 Ford Crown Victoria?
A: First disable air suspension electrical power through the air suspension service switch OFF position to stop undesirable air spring inflation or deflation because this could move the vehicle position during service operations. You should depower the fire suppression system before starting maintenance on vehicles that have this equipment. Set the vehicle shift lever to NEUTRAL for hoisting the vehicle. Cut off the brake caliper flow bolt and detach the brake hose from the brake caliper by discarding the copper washers and plugging the hose. Guide pins along with guide pin boots require no removal unless there is a reason for suspicion since these components possess a permanent seal and lack repairability. First examine the brake caliper for leaks and binding slide pins while you remove its two bolts and caliper before proceeding to new caliper installation. Install the new caliper by placing its antirattle clips properly while replacing them if they show signs of wear or damage. Use the two caliper bolts to install the brake caliper you must tighten them to 25 Nm (18 ft. lbs.). After that, place the brake hose and install the brake caliper flow bolt with two new copper washers and tighten it to 50 Nm (37 ft. lbs.). The brake line needs clearing while fire suppressant systems require new power supplies. Before driving the vehicle, check correct operational status by applying the brakes multiple times while the service switch remains in the ON position if this feature applies to your vehicle.