How to service the muffler and tailpipe assembly on a 4.6L engine on 2006 Ford E-250?

When servicing the muffler and tailpipe assembly of a 4.6L engine it is essential to wait until the exhaust system cools down properly to prevent injuries since the catalytic converter reaches hazardous temperatures rapidly. Using oil or grease based lubricants should be avoided on isolators because they cause rubber deterioration which leads to possible separation of the exhaust hanger bracket. Put the vehicle in neutral mode at the same time set it up on a hoist. A safety stand should hold the muffler and tailpipe assembly after which you can remove all hanger isolators. After loosening the Torca clamp nut on the muffler you should reduce tension but ensure proper torque of 40 Nm when reattaching. Begin by disassembling the muffler and tailpipe from the catalytic converter and then proceed with removing all operational parts from the assembly. Follow the same steps that were used for removal to properly install the exhaust system components.

OEM 2006 Ford E-250 Muffler

Exhaust Muffler

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Mufflers found

View related parts
2006 Ford E-250 Muffler, Front Part Number: 6C2Z-5230-A
Product Specifications
- Other Name: Muffler And Pipe Assembly - Rear; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit
- Position: Front
- Replaces: 6C2Z-5230-DA
- Base No.: 5230
- Item Weight: 45.50 Pounds
- Item Dimensions: 79.3 x 34.7 x 16.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6C2Z-5230-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford E-250 Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2006 Ford E-250 Muffler, Rear Part Number: 6C2Z-5230-NE
Product Specifications
- Other Name: Muffler And Pipe Assembly - Rear; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe
- Position: Rear
- Replaces: 6C2Z-5230-E
- Base No.: 5230
- Item Weight: 35.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6C2Z-5230-NE
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford E-250 Submodels:
- Base | 8 Cyl 4.6 L GAS
View related parts
2006 Ford E-250 Muffler, Rear Part Number: 6C2Z-5230-NA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Muffler And Pipe Assembly - Rear
- Manufacturer Note: Muffler asy. - exc. 124" WB Stripped Chassis - FROM 4/18/05 to 6/20/2005
- Position: Rear
- Replaces: 4C2Z-5230-NB
- Base No.: 5230
- Item Weight: 34.30 Pounds
- Item Dimensions: 31.2 x 13.3 x 111.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6C2Z-5230-NA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford E-250 Submodels:
- Base | 8 Cyl 4.6 L GAS
View related parts
2006 Ford E-250 Muffler, Rear Part Number: 6C2Z-5230-HC
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Muffler And Pipe Assembly - Rear
- Position: Rear
- Replaces: 6C2Z-5230-HA
- Base No.: 5230
- Item Weight: 44.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6C2Z-5230-HC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford E-250 Submodels:
- Base | 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS

2006 Ford E-250 Muffler

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2006 Ford E-250 Muffler available at FordPartsDeal.com. You can confidently purchase our OEM 2006 Ford E-250 Muffler as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2006 Ford E-250 Muffler Parts Q&A

Q: How to service the muffler and tailpipe assembly on a 4.6L engine on 2006 Ford E-250?
A: When servicing the muffler and tailpipe assembly of a 4.6L engine it is essential to wait until the exhaust system cools down properly to prevent injuries since the catalytic converter reaches hazardous temperatures rapidly. Using oil or grease based lubricants should be avoided on isolators because they cause rubber deterioration which leads to possible separation of the exhaust hanger bracket. Put the vehicle in neutral mode at the same time set it up on a hoist. A safety stand should hold the muffler and tailpipe assembly after which you can remove all hanger isolators. After loosening the Torca clamp nut on the muffler you should reduce tension but ensure proper torque of 40 Nm when reattaching. Begin by disassembling the muffler and tailpipe from the catalytic converter and then proceed with removing all operational parts from the assembly. Follow the same steps that were used for removal to properly install the exhaust system components.