FordParts
My Garage
My Account
Cart
OEM 2006 Mercury Montego Catalytic Converter
Cat. Converter- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
5 Catalytic Converters found
2006 Mercury Montego Catalytic Converter, Front Driver Side Part Number: 7G1Z-5E213-A
$758.58 MSRP: $1049.43You Save: $290.85 (28%)Product Specifications- Other Name: Converter Assembly; Catalytic Converter, Front Forward; Preconverter
- Position: Front Driver Side
- Base No.: 5F250
- Item Weight: 9.20 Pounds
- Item Dimensions: 14.3 x 12.2 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7G1Z-5E213-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Product Specifications- Other Name: Converter Assembly; Catalytic Converter, Front Rearward; Preconverter
- Position: Front Passenger Side
- Base No.: 5E212A
- Item Weight: 9.20 Pounds
- Item Dimensions: 14.4 x 12.2 x 8.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7G1Z-5E212-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
- Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Front Forward; Preconverter
- Position: Front Driver Side
- Base No.: 5F250
- Item Weight: 10.50 Pounds
- Item Dimensions: 14.7 x 12.2 x 8.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7F9Z-5E213-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Product Specifications- Other Name: Converter Assembly; Catalytic Converter, Rear
- Position: Rear
- Base No.: 5E212B
- Item Weight: 7.20 Pounds
- Item Dimensions: 14.6 x 12.1 x 8.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7F9Z-5E212-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
- Product Specifications
- Other Name: Converter Assembly; Catalytic Converter, Front Rearward; Preconverter
- Position: Front Passenger Side
- Base No.: 5E212A
- Item Weight: 10.20 Pounds
- Item Dimensions: 14.3 x 12.2 x 8.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7F9Z-5E212-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2006 Mercury Montego Catalytic Converter
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2006 Mercury Montego Catalytic Converter available at FordPartsDeal.com. You can confidently purchase our OEM 2006 Mercury Montego Catalytic Converter as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2006 Mercury Montego Catalytic Converter Parts Q&A
- Q: How to properly service a catalytic converter on 2006 Mercury Montego?A: Service the catalytic converter only after the exhaust system has cooled to safety since the catalytic converter especially reaches high operating temperatures right after engine startup. Reassembling the exhaust requires new fasteners bearing the same part number as the originals because exhaust fasteners rely on torque prevailing design while following specified torque values will guarantee exhaust component retention. The front catalytic converter requires removal of the 2 upper converter-to-exhaust manifold bolts and gasket which should then be replaced by a new gasket before tightening to 40 Nm (30 ft. lbs.). The vehicle needs to be placed on a hoist in neutral position while technicians should also remove the bracket bolt during front catalytic converter removal and tighten the bolt to 40 Nm (30 ft. lbs.). Remove the sensor cable connector of the catalyst monitor followed by removing and discarding the two lower nuts holding the front or rear catalytic converter. A new gasket should be used during installation followed by alternating the catalytic converter nuts to keep the exhaust flanges parallel while final tightening to 40 Nm (30 ft. lbs.). Inspect the bracket clamp of the front catalytic converter for replacement while tightening the clamp bolt to 40 Nm (30 ft. lbs.). You should prepare the catalyst monitor sensor threads with anti-seize lubricant then remove the sensor while tightening it to 47 Nm (35 ft. lbs.). The installation process should begin with mating surface cleaning and follow all steps in reverse order to install new gaskets and exhaust fasteners.