How to service and repair the front parking brake cable on 2007 Ford Crown Victoria?

One needs to start front parking brake cable service and repair by using the parking brake release handle to let go of park brake control. The air suspension switch in the luggage compartment needs to be switched off to prevent unanticipated air spring activities while hoisting, jacking or towing. The service of the front parking brake cable needs to start after disconnecting the fire suppression system's depowering. Position the neutral gear transmission vehicle onto the hoist. Completion of parking brake control application requires pulling the adjuster clip down before securing it with upward resistance. To secure the adjuster raise the parking brake adjuster clip until it locks before letting go of the parking brake control. The technician disconnects front parking brake cable and conduit from LH parking brake rear cable and conduit at cable connector and removes front parking brake cable and conduit retainer by pressing its retaining tabs. Replace the parking brake cable bracket bolt and remove the bracket component after bolting it to a torque of 9 Nm (80 inch lbs.). We should first disconnect both front parking brake cable and conduit from the parking brake control before pushing the assembly downward for removal. Follow the opposite sequence of uninstallation to install while adjusting the parking brake cable tension. After finishing any installation on vehicles with fire suppression systems you must initiate the system reactivation.

OEM 2007 Ford Crown Victoria Parking Brake Cable

Emergency Parking Brake Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Parking Brake Cables found

View related parts
2007 Ford Crown Victoria Front Cable
Part Number: 3W1Z-2853-AA
$39.96 MSRP: $63.45
You Save: $23.49 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Parking Brake Cable, Front; Brake Cable
- Position: Front
- Base No.: 2853
- Item Weight: 1.70 Pounds
- Item Dimensions: 0.1 x 14.1 x 14.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3W1Z-2853-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2007 Ford Crown Victoria Rear Cable, Driver Side
Part Number: 5W7Z-2A635-B
$54.79 MSRP: $75.80
You Save: $21.01 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: LH, Police with FSS (Fire Suppression System)
- Position: Driver Side
- Base No.: 2A635
- Item Weight: 1.40 Pounds
- Item Dimensions: 4.7 x 3.9 x 28.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5W7Z-2A635-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2007 Ford Crown Victoria Rear Cable, Passenger Side
Part Number: 6W1Z-2A635-AA
$53.59 MSRP: $74.13
You Save: $20.54 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: RH, Less natural gas vehicle
- Position: Passenger Side
- Replaces: 3W1Z-2A635-AA
- Base No.: 2A635
- Item Weight: 2.40 Pounds
- Item Dimensions: 4.6 x 17.8 x 17.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W1Z-2A635-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2007 Ford Crown Victoria Rear Cable, Driver Side
Part Number: 4W7Z-2A635-AA
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: LH, Less Natural Gas Vehicle-Less long wheelbase
- Position: Driver Side
- Replaces: 3W7Z-2A635-CA
- Base No.: 2A635
- Item Weight: 1.80 Pounds
- Item Dimensions: 4.7 x 3.9 x 28.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4W7Z-2A635-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS

2007 Ford Crown Victoria Parking Brake Cable

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2007 Ford Crown Victoria Parking Brake Cable available at FordPartsDeal.com. You can confidently purchase our OEM 2007 Ford Crown Victoria Parking Brake Cable as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2007 Ford Crown Victoria Parking Brake Cable Parts Questions & Experts Answers

Q: How to service and repair the front parking brake cable on 2007 Ford Crown Victoria?
A: One needs to start front parking brake cable service and repair by using the parking brake release handle to let go of park brake control. The air suspension switch in the luggage compartment needs to be switched off to prevent unanticipated air spring activities while hoisting, jacking or towing. The service of the front parking brake cable needs to start after disconnecting the fire suppression system's depowering. Position the neutral gear transmission vehicle onto the hoist. Completion of parking brake control application requires pulling the adjuster clip down before securing it with upward resistance. To secure the adjuster raise the parking brake adjuster clip until it locks before letting go of the parking brake control. The technician disconnects front parking brake cable and conduit from LH parking brake rear cable and conduit at cable connector and removes front parking brake cable and conduit retainer by pressing its retaining tabs. Replace the parking brake cable bracket bolt and remove the bracket component after bolting it to a torque of 9 Nm (80 inch lbs.). We should first disconnect both front parking brake cable and conduit from the parking brake control before pushing the assembly downward for removal. Follow the opposite sequence of uninstallation to install while adjusting the parking brake cable tension. After finishing any installation on vehicles with fire suppression systems you must initiate the system reactivation.