FordParts
My Garage
My Account
Cart
OEM 2007 Ford F-150 Muffler
Exhaust Muffler- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 Mufflers found
2007 Ford F-150 Muffler W/Tpipe, Rear Part Number: 4L3Z-5230-A
$398.90 MSRP: $547.29You Save: $148.39 (28%)Product Specifications- Other Name: Muffler And Pipe Assembly - Rear; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Position: Rear
- Replaces: 6L3Z-5230-DA, 6L3Z-5230-HA, 8L3Z-5230-B, 5L3Z-5230-MA, 4L3Z-5230-BB, 6L3Z-5230-FA, 8L3Z-5230-D, 5L3Z-5230-BA
- Base No.: 5230
- Item Weight: 48.60 Pounds
- Item Dimensions: 98.9 x 50.4 x 20.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4L3Z-5230-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2007 Ford F-150 Muffler W/Tpipe, Front Part Number: 4L3Z-5230-B
$514.16 MSRP: $676.12You Save: $161.96 (24%)Product Specifications- Other Name: Muffler And Pipe Assembly - Rear; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Position: Front
- Replaces: 4L3Z-5230-AB, 6L3Z-5230-GA, 8L3Z-5230-A, 5L3Z-5230-LA, 8L3Z-5230-C, 6L3Z-5230-CA
- Base No.: 5230
- Item Weight: 49.10 Pounds
- Item Dimensions: 94.4 x 19.1 x 13.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4L3Z-5230-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2007 Ford F-150 Muffler W/Tpipe, Rear Part Number: 7L3Z-5230-AA
Product Specifications- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler And Pipe Assembly - Rear; Muffler
- Manufacturer Note: Extension Pipes (5A212) And Mufflers (5230) Are To Be Replaced As A Set
- Position: Rear
- Base No.: 5230A
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L3Z-5230-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2007 Ford F-150 Muffler
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2007 Ford F-150 Muffler available at FordPartsDeal.com. You can confidently purchase our OEM 2007 Ford F-150 Muffler as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2007 Ford F-150 Muffler Parts Q&A
- Q: How to service and repair the muffler and tailpipe on 2007 Ford F-150?A: The first step to repair the muffler and tailpipe requires your vehicle to be set to neutral at a hoist. The use of oil or grease-based lubricants on isolators should be avoided because they deteriorate rubber material. Always install new exhaust intermediate pipe and clamp assembly during the process of unfastening the exhaust intermediate pipe-to-muffler assembly clamp. Start by easing the clamp then remove the bolt securing the front part of the muffler exhaust hanger bracket and its associated isolator from the frame. This action should be followed by removing the bolts from the rear muffler exhaust hanger bracket and isolator and then the bolts from the tailpipe exhaust hanger bracket and its isolator. Remove all components before extracting the combination of muffler and tailpipe unit. Start with the vehicle front end before tightening any fasteners during the installation process of all assembled components. Cleaning the exhaust clamp contact area demands an abrasive pad to eliminate rust buildup on surfaces. Fitting begins with placing the muffler and tailpipe assembly before installing the front muffler exhaust hanger bracket with its isolator to the frame and tightens it to 30 Nm (22 ft. lbs.). Move onto the rear muffler exhaust hanger bracket along with its isolator before you tighten both to 30 Nm (22 ft. lbs.) and then proceed with the tailpipe exhaust hanger bracket and its isolator which needs to be tightened to 30 Nm (22 ft. lbs.). Reshape the exhaust system before tightening all exhaust system clamps. The bolt of the idler pulley should be extracted before final installation where it requires a torque of 25 Nm (18 ft. lbs.). Reinstall by doing the removal steps in reverse order.