How to service and repair the upper control arm on 2007 Ford Focus?

You should start upper control arm servicing by hoisting the vehicle with its transmission set to neutral. Replace the old shock absorber lower bolt with a new one and fasten it at 103 Nm (76 ft. lbs.). You need to remove then discard the upper arm inboard bolt before installation when you must tighten it to 115 Nm (85 ft. lbs.). Note down the initial upper arm position before removing it through the discarding of the outboard bolt and making adjustments to the shock absorber if necessary. While implementing the upper arm reinstallation process make sure to secure the outboard bolt to 115 Nm (85 ft. lbs.). Install and tighten upper arm bolts by following this procedure when the suspension rests at curb height. The removal procedure should be reversed to complete installation. Proper suspension system performance depends on following specified torque values while only installing new parts of identical part numbers.

OEM 2007 Ford Focus Control Arm

Suspension Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Control Arms found

View related parts
2007 Ford Focus Lower Control Arm, Front Driver Side Part Number: 6W4Z-3079-AA
Product Specifications
- Other Name: Arm Assembly - Front Suspension; Suspension Control Arm; Control Arm
- Manufacturer Note: 16MM Ball-Joint Stud Hole
- Position: Front Driver Side
- Replaces: 4W4Z-3079-AA
- Base No.: 3078
- Item Weight: 12.10 Pounds
- Item Dimensions: 4.8 x 16.8 x 18.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6W4Z-3079-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Focus Submodels:
- S, SE, SES, ST, ZX3, ZX4, ZX4 ST, ZX5, ZXW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
2007 Ford Focus Lower Control Arm, Front Driver Side Part Number: 7S4Z-3079-A
Product Specifications
- Other Name: Arm Assembly - Front Suspension; Front Left Control Arm and Ball Joint Assembly; Control Arm
- Position: Front Driver Side
- Replaces: 6S4Z-3079-AA
- Base No.: 3078
- Item Weight: 9.80 Pounds
- Item Dimensions: 3.1 x 13.5 x 18.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7S4Z-3079-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Focus Submodels:
- S, SE, SES, ST, ZX3, ZX4, ZX4 ST, ZX5, ZXW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
2007 Ford Focus Lower Control Arm, Front Passenger Side Part Number: 7S4Z-3078-A
Product Specifications
- Other Name: Arm Assembly - Front Suspension; Front Right Control Arm and Ball Joint Assembly; Control Arm
- Position: Front Passenger Side
- Replaces: 6S4Z-3078-AA
- Base No.: 3078
- Item Weight: 10.00 Pounds
- Item Dimensions: 3.1 x 14.0 x 17.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7S4Z-3078-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Focus Submodels:
- S, SE, SES, ST, ZX3, ZX4, ZX4 ST, ZX5, ZXW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS

2007 Ford Focus Control Arm

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2007 Ford Focus Control Arm available at FordPartsDeal.com. You can confidently purchase our OEM 2007 Ford Focus Control Arm as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2007 Ford Focus Control Arm Parts Q&A

Q: How to service and repair the upper control arm on 2007 Ford Focus?
A: You should start upper control arm servicing by hoisting the vehicle with its transmission set to neutral. Replace the old shock absorber lower bolt with a new one and fasten it at 103 Nm (76 ft. lbs.). You need to remove then discard the upper arm inboard bolt before installation when you must tighten it to 115 Nm (85 ft. lbs.). Note down the initial upper arm position before removing it through the discarding of the outboard bolt and making adjustments to the shock absorber if necessary. While implementing the upper arm reinstallation process make sure to secure the outboard bolt to 115 Nm (85 ft. lbs.). Install and tighten upper arm bolts by following this procedure when the suspension rests at curb height. The removal procedure should be reversed to complete installation. Proper suspension system performance depends on following specified torque values while only installing new parts of identical part numbers.