What precautions should be taken when servicing a shock absorber to prevent personal injury and ensure proper installation on 2008 Ford Mustang?

The servicing procedure requires complete avoidance of heat exposure to both shock absorber and strut tube because these components contain gas-pressure which could result in dangerous explosion incidents. It is essential to keep all body parts out of range from shock absorbers and strut rods since these components have the ability to automatically extend without warning. Suspension fasteners form a vital link that controls key system operations thus new components must receive versions that maintain the original part numbers or their equivalent without accepting substandard alternatives for replacement. The reassembly process requires following torque values to maintain correct retention of the components. A frame-lifting hoist needs shock absorber implementations that involve single installation to shield the control arm bushings and require a drive-on hoist type over frame-activated systems. After opening the luggage compartment users must move aside the carpet before marking the rear shock absorber in position on the vehicle's level surface. Place two proper jackstands beneath the rear axle to support the suspension while keeping away from the differential housing for protection. Remove the tire and wheel before starting this process. After taking out the shock absorber upper nut and washer along with its insulator assembly you need to tighten the new nut to 40 Nm (30 lb-ft). The raising of the rear axle should guide the mark on the rear shock absorber towards the protective sleeve before shock absorber lower bolt and nut removal. Install the new bolt at 115 Nm (85 lb-ft) torque during installation. Proper clamp load and bushing protection requires the tightening of shock absorber lower bolts at curb height. Complete the installation by performing a backward procedure.

OEM 2008 Ford Mustang Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Shock Absorbers found

View related parts
2008 Ford Mustang Strut, Front
Part Number: AR3Z-18124-D
$142.67 MSRP: $234.75
You Save: $92.08 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assembly; Front Suspension Strut Kit; Complete Strut Set.; Shock Absorber
- Manufacturer Note: Fits Both LH & RH Sides
- Position: Front
- Replaces: 6R3Z-18124-EA, 7R3Z-18124-B, 7R3Z-18124-GB, 9R3Z-18124-J, AST-383, ASH-1167, AST-169, 9R3Z-18124-B, ASH-12155, AST-386, ASH-1028, 6R3Z-18124-BA, 7R3Z-18124-E, 9R3Z-18124-F, AR3Z-18124-E, AST-446, AST-451, ASH-1054, AR3Z-18124-B, AR3Z-18124-G, 8R3Z-18124-J, 9R3Z-18124-E, 7R3Z-18124-GA, ASH-1031, AST-447, ASH-1106, AST-450
- Base No.: 18124
- Item Weight: 15.20 Pounds
- Item Dimensions: 31.9 x 7.5 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: AR3Z-18124-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Bullitt, GT, Shelby GT, Shelby GT500, Shelby GT500KR | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford Mustang Shock Absorber, Rear
Part Number: 7R3Z-18125-L
$63.43 MSRP: $104.36
You Save: $40.93 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Shock Absorber; Rear Suspension Strut and Shock Assembly; Complete Strut Set.; Shock; Suspension Shock Absorber
- Position: Rear
- Replaces: 4R3Z-18125-CA, 6R3Z-18125-CA, 6R3Z-18125-FA, 6R3Z-18125-DA, 7R3Z-18125-HA, 6R3Z-18125-C, AR3Z-18125-G, AST-173, AST-416, 6R3Z-18125-MA, ASH-1057, AST-224
- Base No.: 18125
- Item Weight: 5.00 Pounds
- Item Dimensions: 19.7 x 3.0 x 2.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 7R3Z-18125-L
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base, GT, Shelby GT, Shelby GT500 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford Mustang Shock Absorber, Rear
Part Number: 7R3Z-18125-J
$69.39 MSRP: $114.18
You Save: $44.79 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Shock Absorber; Rear Suspension Strut and Shock Assembly; Complete Strut Set.; Shock; Suspension Shock Absorber
- Position: Rear
- Base No.: 18125
- Item Weight: 4.90 Pounds
- Item Dimensions: 19.5 x 2.9 x 2.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 7R3Z-18125-J
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base | 6 Cyl 4.0 L GAS
View related parts
2008 Ford Mustang Shock Absorber, Rear
Part Number: 6R3Z-18125-LA
$69.39 MSRP: $114.18
You Save: $44.79 (40%)
ADD TO CART
Product Specifications
- Other Name: Kit - Shock Absorber; Rear Suspension Strut and Shock Assembly; Complete Strut Set.; Shock; Suspension Shock Absorber
- Position: Rear
- Replaces: 4R3Z-18125-BA, 6R3Z-18125-GA, 6R3Z-18125-EA, 7R3Z-18125-M, ASH-412, ASH-1168, AST-263, AST-172, 6R3Z-18125-BA, 8R3Z-18125-J, 6R3Z-18125-B, 7R3Z-18125-GA, AR3Z-18125-B, ASH-1056, 7R3Z-18125-GB, ASH-1108, ASH-12156
- Base No.: 18125
- Item Weight: 4.60 Pounds
- Item Dimensions: 19.2 x 3.4 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 6R3Z-18125-LA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base, Bullitt, GT, Shelby GT, Shelby GT500, Shelby GT500KR | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford Mustang Strut, Front
Part Number: 9R3Z-18124-C
$143.65 MSRP: $236.36
You Save: $92.71 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assembly; Front Suspension Strut Kit; Complete Strut Set.; Shock Absorber
- Position: Front
- Replaces: 6R3Z-18124-CA, 6R3Z-18124-FA, 7R3Z-18124-C, 9R3Z-18124-H, 7R3Z-18124-HB, 9R3Z-18124-D, AR3Z-18124-F, ASH-1055, ASH-1112, ASH-1107, AST-170, AST-387, AR3Z-18124-C, ASH-1246, 7R3Z-18124-J, 7R3Z-18124-F, 7R3Z-18124-D, ASH-1032, AST-449, AST-384, 7R3Z-18124-HA
- Base No.: 18124
- Item Weight: 14.70 Pounds
- Item Dimensions: 31.6 x 7.5 x 7.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 9R3Z-18124-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base, Bullitt, GT, Shelby GT, Shelby GT500, Shelby GT500KR | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford Mustang Strut, Front
Part Number: 9R3Z-18124-G
$108.30 MSRP: $181.82
You Save: $73.52 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assembly; Front Suspension Strut Kit; Complete Strut Set.; Shock Absorber
- Position: Front
- Replaces: 7R3Z-18124-A, 6R3Z-18124-AA
- Base No.: 18124
- Item Weight: 14.60 Pounds
- Item Dimensions: 31.9 x 7.4 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 9R3Z-18124-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base, Bullitt, GT, Shelby GT, Shelby GT500, Shelby GT500KR | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2008 Ford Mustang Shock Absorber, Rear
Part Number: 7R3Z-18125-K
$130.53 MSRP: $207.27
You Save: $76.74 (38%)
ADD TO CART
Product Specifications
- Other Name: Kit - Shock Absorber; Rear Suspension Strut and Shock Assembly; Complete Strut Set.; Shock; Suspension Shock Absorber
- Position: Rear
- Base No.: 18125
- Item Weight: 4.60 Pounds
- Item Dimensions: 19.5 x 2.8 x 3.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 7R3Z-18125-K
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2008 Ford Mustang Submodels:
- Base | 6 Cyl 4.0 L GAS

2008 Ford Mustang Shock Absorber

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2008 Ford Mustang Shock Absorber available at FordPartsDeal.com. You can confidently purchase our OEM 2008 Ford Mustang Shock Absorber as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2008 Ford Mustang Shock Absorber Parts Questions & Experts Answers

Q: What precautions should be taken when servicing a shock absorber to prevent personal injury and ensure proper installation on 2008 Ford Mustang?
A: The servicing procedure requires complete avoidance of heat exposure to both shock absorber and strut tube because these components contain gas-pressure which could result in dangerous explosion incidents. It is essential to keep all body parts out of range from shock absorbers and strut rods since these components have the ability to automatically extend without warning. Suspension fasteners form a vital link that controls key system operations thus new components must receive versions that maintain the original part numbers or their equivalent without accepting substandard alternatives for replacement. The reassembly process requires following torque values to maintain correct retention of the components. A frame-lifting hoist needs shock absorber implementations that involve single installation to shield the control arm bushings and require a drive-on hoist type over frame-activated systems. After opening the luggage compartment users must move aside the carpet before marking the rear shock absorber in position on the vehicle's level surface. Place two proper jackstands beneath the rear axle to support the suspension while keeping away from the differential housing for protection. Remove the tire and wheel before starting this process. After taking out the shock absorber upper nut and washer along with its insulator assembly you need to tighten the new nut to 40 Nm (30 lb-ft). The raising of the rear axle should guide the mark on the rear shock absorber towards the protective sleeve before shock absorber lower bolt and nut removal. Install the new bolt at 115 Nm (85 lb-ft) torque during installation. Proper clamp load and bushing protection requires the tightening of shock absorber lower bolts at curb height. Complete the installation by performing a backward procedure.