FordParts
My Garage
My Account
Cart
OEM 2008 Mercury Mountaineer Parking Brake Cable
Emergency Parking Brake Release Cable- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 Parking Brake Cables found
2008 Mercury Mountaineer Front Cable Part Number: 7L2Z-2853-A
$27.44 MSRP: $44.55You Save: $17.11 (39%)Product Specifications- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Replaces: 6L2Z-2853-AA
- Base No.: 2853
- Item Weight: 1.20 Pounds
- Item Dimensions: 36.7 x 6.2 x 6.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L2Z-2853-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Product Specifications- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Driver Side
- Replaces: 7L2Z-2A635-A, 7L2Z-2A635-C
- Base No.: 2A635
- Item Weight: 1.70 Pounds
- Item Dimensions: 1.6 x 1.5 x 45.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L2Z-2A635-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Product Specifications- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Passenger Side
- Replaces: 7L2Z-2A635-B, 6L2Z-2A635-A
- Base No.: 2A635
- Item Weight: 1.40 Pounds
- Item Dimensions: 0.1 x 14.1 x 14.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L2Z-2A635-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2008 Mercury Mountaineer Parking Brake Cable
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2008 Mercury Mountaineer Parking Brake Cable available at FordPartsDeal.com. You can confidently purchase our OEM 2008 Mercury Mountaineer Parking Brake Cable as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2008 Mercury Mountaineer Parking Brake Cable Parts Q&A
- Q: How to remove and replace the front parking brake cable on 2008 Mercury Mountaineer?A: The vehicle must be set to neutral position while hanging from a hoist before beginning the removal and replacement of the front parking brake cable. Start the procedure by uninstalling the hood latch release handle screw along with the screw keeping the hood latch release handle in place. Then remove the pin-type retainer and the LH A-pillar lower trim panel. The cable assembly hood latch release requires screw removal followed by its placement aside. Unlock the parking brake cable tension while taking out the two screws securing the instrument panel steering column cover. The two parking brake release handle bolts need to be detached from their bracket alignment before being restored with a torque of 3 Nm (27 lb-in). First disconnect the parking brake switch electrical connector and remove the wiring harness bracket screw. Place the harness and bracket out of the way. Install the three bolts of the parking brake control by tightening them to 20 Nm (15 lb-ft) torque. Proceed by shifting the carpet while keeping in mind that the parking brake control take-up spool tab might require bending for cable access. Disconnect the parking brake control from its front parking brake cables. Then unfasten the front brake cables from their conduit and their bracket before removing everything. Testing of the parking brake system should follow the installation process for proper operation.