How to service and repair the front parking brake cable on Mercury Mountaineer?

The front parking brake cable repair and servicing process begins by hoisting the vehicle to check for neutral position. The service begins with unscrewing the hood latch release handle along with the screw followed by removing the pin-type retainer and the LH A-pillar lower trim panel. Remove the hood latch release cable assembly screw then place the release cable assembly to the side. Move the tension off the parking brake cable before taking out two screws which secure the instrument panel steering column cover. Reinstall the two parking brake release handle bolts on their bracket while torquing them to 3 Nm (27 inch lbs). Testing the parking brake switch electrical connector then removing the wiring harness bracket screw gives you space for the connector and bracket. The technician should remove three parking brake control bolts while securing them to 20 Nm (15 ft. lbs.) torque during installation. When moving the carpet you should also note that you might need to bend the parking brake control take-up spool tab to remove the cable. Begin by detaching the front parking brake cables from the parking brake control unit and proceed with disconnecting the cable conduit and bracket cable before taking out the control assembly. Complete installation requires performing the reverse steps from removal and testing the parking brake functionality.

How to remove and replace the rear left parking brake cable on Mercury Mountaineer?

The first step for changing the rear left parking brake cable involves releasing the parking brake tension. Set neutral gear on the vehicle and hang it from the hoist. Start by removing the wire form bolt followed by the bracket bolt while tightening them to 23 Nm (17 lb-ft). The installation sequence begins with removing the intermediate cable from its position at the cable equalizer and proceeds with unfastening the front end of the left rear cable conduit at the frame bracket. After disconnecting the left parking brake cable from the parking brake lever you should remove the cable. When installing the new cable you must reverse the removal method while performing tests on the parking brake system to check its proper functioning.

OEM Mercury Mountaineer Parking Brake Cable

Emergency Parking Brake Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Parking Brake Cables found

View related parts
Mercury Mountaineer Front Cable Part Number: 4L5Z-2853-AA
$36.07 MSRP: $57.27
You Save: $21.20 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Parking Brake Cable, Front; Brake Cable
- Position: Front
- Replaces: 3L5Z-2853-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Rear Cable, Passenger Side Part Number: 1L2Z-2A635-BA
$21.22 MSRP: $28.87
You Save: $7.65 (27%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: Cable asy. - RH
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Front Cable Part Number: 7L2Z-2853-A
$27.44 MSRP: $44.55
You Save: $17.11 (39%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Replaces: 6L2Z-2853-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Rear Cable, Driver Side Part Number: 1L2Z-2A635-BB
$24.26 MSRP: $33.56
You Save: $9.30 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Parking Brake Cable; Brake Cable
- Manufacturer Note: Cable asy. - LH
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Rear Cable, Driver Side Part Number: 8L2Z-2A635-B
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Driver Side
- Replaces: 7L2Z-2A635-A, 7L2Z-2A635-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Mercury Mountaineer | Base, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Rear Cable, Driver Side Part Number: 2C5Z-2A635-AB
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Rear Cable, Driver Side Part Number: F87Z-2A635-GB
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: Cable (brake rear) - LH - 1998/2001
- Position: Driver Side
- Replaces: F67Z-2A635-EA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2000 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Rear Cable, Passenger Side Part Number: F67Z-2A635-AA
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: Cable (brake rear) - RH - 1996/2001
- Position: Passenger Side
- Replaces: F5TZ-2A635-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2000 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Rear Cable, Passenger Side Part Number: 8L2Z-2A635-A
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Passenger Side
- Replaces: 7L2Z-2A635-B, 6L2Z-2A635-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Rear Cable, Driver Side Part Number: 6L2Z-2A635-AB
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Mercury Mountaineer | Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Rear Cable, Passenger Side Part Number: 6L2Z-2A635-AA
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006 Mercury Mountaineer | Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Front Cable Part Number: 4L2Z-2853-BA
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Replaces: 2C5Z-2853-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Front Cable Part Number: 1L2Z-2853-BA
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Parking Brake Cable; Brake Cable
- Manufacturer Note: Cable asy. (park brake front)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS

Mercury Mountaineer Parking Brake Cable

OEM Parking Brake Cable boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Parking Brake Cable with long life and a perfect fit. Come to our website and find genuine Mercury Mountaineer parts. We keep a wide inventory of OEM Mountaineer parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Parking Brake Cable is an important item that stimulates the dependability and efficiency of the Mercury Mountaineer, mid-size luxury SUV manufactured by the Mercury from 1996 to 2010. This basic Parking Brake Cable links the parking brake system to the total braking system of the car thus making the Mercury Mountaineer non-moving particularly in inclined positions for increased safety and stability. This recognition of compatibility with all Mountaineer models made throughout the product's production is another advantage of this Parking Brake Cable, which in its design, provided for the requirements for each model. The Mercury Mountaineer includes many luxury elements and offers great power and the quality of its Parking Brake Cable should not be doubted. Due to use over time the Parking Brake Cable is meant to be a failure and users can be put at risk by inadequate braking force. If the Parking Brake Cable is failing, one will experience is difficulty in engaging the brake, and the presence of warning lights that call for a service. Parking Brake Cable, as for any car product, is in high demand and crucial because it guarantees the functionality of the parking system. This Parking Brake Cable provides safety and efficiency during the course of driving and is a great part of any Mercury vehicle proving that Mercury vehicles are safe and performant.

Mercury Mountaineer Parking Brake Cable Parts and Q&A

Front Cable
7L2Z-2853-A
Q: How to service and repair the front parking brake cable on Mercury Mountaineer?
A:
The front parking brake cable repair and servicing process begins by hoisting the vehicle to check for neutral position. The service begins with unscrewing the Hood Latch release handle along with the screw followed by removing the pin-type retainer and the LH A-pillar lower trim panel. Remove the hood latch release cable assembly screw then place the release cable assembly to the side. Move the tension off the parking brake cable before taking out two screws which secure the instrument panel Steering Column Cover. Reinstall the two parking brake release handle bolts on their bracket while torquing them to 3 Nm (27 inch lbs). Testing the parking brake switch electrical connector then removing the wiring harness bracket screw gives you space for the connector and bracket. The technician should remove three parking brake control bolts while securing them to 20 Nm (15 ft. lbs.) torque during installation. When moving the carpet you should also note that you might need to bend the parking brake control take-up spool tab to remove the cable. Begin by detaching the front parking brake cables from the parking brake control unit and proceed with disconnecting the cable conduit and bracket cable before taking out the control assembly. Complete installation requires performing the reverse steps from removal and testing the parking brake functionality.
Rear Cable, Driver Side
8L2Z-2A635-B
Q: How to remove and replace the rear left parking brake cable on Mercury Mountaineer?
A:
The first step for changing the rear left parking brake cable involves releasing the parking brake tension. Set neutral gear on the vehicle and hang it from the hoist. Start by removing the wire form bolt followed by the bracket bolt while tightening them to 23 Nm (17 lb-ft). The installation sequence begins with removing the intermediate cable from its position at the cable equalizer and proceeds with unfastening the front end of the left rear cable conduit at the frame bracket. After disconnecting the left parking brake cable from the parking brake lever you should remove the cable. When installing the new cable you must reverse the removal method while performing tests on the parking brake system to check its proper functioning.