How to Service and Repair the Motor and Transmission Mount for the Aisin AW21 Transaxle Support Insulator on 2009 Ford Fusion?

Attention should first focus on setting the vehicle in NEUTRAL position on a hoist before removing the battery and tending to the battery tray. Begin by removing four screws which hold the LH fender splash shield while setting it aside then continue with removing six pin-type retainers along with the LH front structure-to-subframe splash shield. The service requires uninstallation of two transaxle insulator-to-frame bolts which are found lower on the structure. The propulsion process for the 3.0L engine includes attaching an Engine Lifting Bracket and Universal Adapter Bracket "L" hook to the LH side of the engine before using an Engine Support Bar to support the engine for bolt removal from the transaxle support insulator-to-bracket. The Oil Pan Holding Fixture needs careful alignment to the oil pan bosses to avoid breaking when servicing the exhaust Y-pipe of the 3.5L engine. Position the floor jack along with the Oil Pan Holding Fixture beneath the oil pan and remove the Air Cleaner (ACL) and the transaxle support insulator through bolt. The procedure requires removal of the upper 2 transaxle insulator-to-frame bolts before uninstalling the transaxle insulator from all vehicles. The installer should brush clean rear transaxle support insulator bolts with a wire brush before applying new threadlock during installation. Place the transaxle support insulator in position before securing its upper 2 bolts that need a torque of 62 Nm (46 lb-ft). During transaxle insulator installation into the 3.5L engine you should tighten the through bolt and flagnut to 130 Nm (96 lb-ft). Put away the floor jack together with the Oil Pan Holding Fixture while reattaching the ACL and exhaust Y-pipe. The transaxle support insulator should be installed on all vehicles where technicians must insert the lower 2 transaxle insulators-to-frame bolts and torque them to 62 Nm (46 lb-ft). The LH splash shield requires installation with its 6 pin-type retainers and 4 screws while being secured. The 3.0L engine requires the installation of 2 transaxle support insulator-to-bracket bolts that should have a torque of 90 Nm (66 lb-ft). Reinstall the battery while putting back the battery tray and finish by taking out both the Universal Adapter Bracket "L" hook and Engine Lifting Bracket and Engine Support Bar from the LH side of the engine.

OEM 2009 Ford Fusion Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Motor And Transmission Mounts found

View related parts
2009 Ford Fusion Strut Assembly
Part Number: 8E5Z-6068-D
$53.78 MSRP: $82.62
You Save: $28.84 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Support Rod; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Torque Strut; Strut
- Replaces: 6E5Z-6068-FC, 6E5Z-6068-B, 6E5Z-6068-A, 8E5Z-6068-A
- Base No.: 6068
- Item Weight: 1.90 Pounds
- Item Dimensions: 8.4 x 4.4 x 3.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8E5Z-6068-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Fusion Strut Assembly, Lower
Part Number: 9E5Z-6068-D
$56.87 MSRP: $82.78
You Save: $25.91 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut, Lower; Engine Support Rod; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Torque Strut; Strut
- Position: Lower
- Replaces: 7E5Z-6068-BA, 8E5Z-6068-C
- Base No.: 6068
- Item Weight: 1.70 Pounds
- Item Dimensions: 8.4 x 4.6 x 3.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9E5Z-6068-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- SE, SEL | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Fusion Transmission Mount
Part Number: 9E5Z-6038-A
$80.12 MSRP: $116.62
You Save: $36.50 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Manual Transmission Mount; Transfer Case Mount
- Replaces: 6E5Z-6038-CB
- Base No.: 6038A
- Item Weight: 5.20 Pounds
- Item Dimensions: 8.1 x 5.9 x 10.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9E5Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- S, SE, SEL | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
2009 Ford Fusion Front Mount
Part Number: 6E5Z-6038-DF
$111.64 MSRP: $162.50
You Save: $50.86 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: 6E5Z-6038-A
- Base No.: 6038B
- Item Weight: 7.90 Pounds
- Item Dimensions: 8.4 x 6.9 x 6.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6E5Z-6038-DF
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- SE, SEL | 6 Cyl 3.0 L GAS
View related parts
2009 Ford Fusion Transmission Mount, Driver Side
Part Number: 6H6Z-6038-BA
$80.12 MSRP: $116.62
You Save: $36.50 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Transfer Case Mount
- Position: Driver Side
- Base No.: 6038A
- Item Weight: 5.80 Pounds
- Item Dimensions: 8.3 x 7.1 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6H6Z-6038-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- SE, SEL | 6 Cyl 3.0 L GAS
View related parts
2009 Ford Fusion Front Mount, Passenger Side
Part Number: 6E5Z-6038-CK
$68.91 MSRP: $100.30
You Save: $31.39 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Manufacturer Note: Requires Multiple Replacment Parts
- Position: Front Passenger Side
- Replaced by: 9E5Z-6038-F
- Base No.: 6038B
- Item Weight: 5.20 Pounds
- Item Dimensions: 9.1 x 8.2 x 7.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6E5Z-6038-CK
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- S, SE, SEL | 4 Cyl 2.3 L GAS
View related parts
2009 Ford Fusion Mount Bracket, Passenger Side
Part Number: 6E5Z-6061-BA
$81.10 MSRP: $100.30
You Save: $19.20 (20%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Support; Engine Mount Bracket; Motor Mount
- Manufacturer Note: When Ordering The Replacing 9E5Z-6061-D You Must Also Order 9E5Z-6038-F
- Position: Passenger Side
- Replaced by: 9E5Z-6038-F
- Base No.: 6061
- Item Weight: 5.10 Pounds
- Item Dimensions: 9.2 x 8.3 x 8.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6E5Z-6061-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- SE, SEL | 6 Cyl 3.0 L GAS
View related parts
2009 Ford Fusion Mount Bracket
Part Number: 9E5Z-6061-A
Product Specifications
- Other Name: Bracket - Engine Support; Engine Mount Bracket; Motor Mount
- Replaces: 6E5Z-6061-AA
- Base No.: 6061
- Item Weight: 1.60 Pounds
- Item Dimensions: 6.1 x 6.1 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9E5Z-6061-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- S, SE, SEL | 4 Cyl 2.3 L GAS
View related parts
2009 Ford Fusion Transmission Mount Bracket, Upper
Part Number: 6E5Z-6031-HA
Product Specifications
- Other Name: Bracket - Engine Mounting; Manual Transmission Mount Bracket, Upper; Transfer Case Mount; Transmission Mount
- Position: Upper
- Base No.: 6031
- Item Weight: 4.90 Pounds
- Item Dimensions: 6.3 x 6.2 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6E5Z-6031-HA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- S, SE, SEL | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
2009 Ford Fusion Transmission Mount Bracket
Part Number: 8E5Z-6031-A
Product Specifications
- Other Name: Bracket - Engine Mounting; Transfer Case Mount; Transmission Mount
- Replaces: 6E5Z-6031-JA
- Base No.: 6031
- Item Weight: 3.50 Pounds
- Item Dimensions: 6.4 x 6.2 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8E5Z-6031-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- S, SE, SEL | 4 Cyl 2.3 L GAS
View related parts
2009 Ford Fusion Transmission Mount Bracket, Driver Side
Part Number: 6E5Z-6031-GA
Product Specifications
- Other Name: Bracket - Engine Mounting; Automatic Transmission Mount Bracket; Transfer Case Mount; Transmission Mount
- Position: Driver Side
- Base No.: 6031
- Item Weight: 3.20 Pounds
- Item Dimensions: 9.2 x 4.9 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6E5Z-6031-GA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Fusion Submodels:
- SE, SEL | 6 Cyl 3.0 L GAS

2009 Ford Fusion Motor And Transmission Mount

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2009 Ford Fusion Motor And Transmission Mount available at FordPartsDeal.com. You can confidently purchase our OEM 2009 Ford Fusion Motor And Transmission Mount as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2009 Ford Fusion Motor And Transmission Mount Parts Questions & Experts Answers

Q: How to Service and Repair the Motor and Transmission Mount for the Aisin AW21 Transaxle Support Insulator on 2009 Ford Fusion?
A: Attention should first focus on setting the vehicle in NEUTRAL position on a hoist before removing the battery and tending to the battery tray. Begin by removing four screws which hold the LH fender splash shield while setting it aside then continue with removing six pin-type retainers along with the LH front structure-to-subframe splash shield. The service requires uninstallation of two transaxle insulator-to-frame bolts which are found lower on the structure. The propulsion process for the 3.0L engine includes attaching an Engine Lifting Bracket and Universal Adapter Bracket "L" hook to the LH side of the engine before using an Engine Support Bar to support the engine for bolt removal from the transaxle support insulator-to-bracket. The Oil Pan Holding Fixture needs careful alignment to the oil pan bosses to avoid breaking when servicing the exhaust Y-pipe of the 3.5L engine. Position the floor jack along with the Oil Pan Holding Fixture beneath the oil pan and remove the Air Cleaner (ACL) and the transaxle support insulator through bolt. The procedure requires removal of the upper 2 transaxle insulator-to-frame bolts before uninstalling the transaxle insulator from all vehicles. The installer should brush clean rear transaxle support insulator bolts with a wire brush before applying new threadlock during installation. Place the transaxle support insulator in position before securing its upper 2 bolts that need a torque of 62 Nm (46 lb-ft). During transaxle insulator installation into the 3.5L engine you should tighten the through bolt and flagnut to 130 Nm (96 lb-ft). Put away the floor jack together with the Oil Pan Holding Fixture while reattaching the ACL and exhaust Y-pipe. The transaxle support insulator should be installed on all vehicles where technicians must insert the lower 2 transaxle insulators-to-frame bolts and torque them to 62 Nm (46 lb-ft). The LH splash shield requires installation with its 6 pin-type retainers and 4 screws while being secured. The 3.0L engine requires the installation of 2 transaxle support insulator-to-bracket bolts that should have a torque of 90 Nm (66 lb-ft). Reinstall the battery while putting back the battery tray and finish by taking out both the Universal Adapter Bracket "L" hook and Engine Lifting Bracket and Engine Support Bar from the LH side of the engine.