How to Service and Repair the Rear Motor and Transmission Mount on Ford Fusion?

Start transaxle rear support insulator service and repair by hoisting the vehicle in NEUTRAL and then removing its splash shield bolts while you also detach the shield before reinstalling all bolts with 47 Nm (35 ft. lbs.) torque. Start by removing the 2 bolts at the bottom of the transaxle rear support insulator while torquing them to 63 Nm (46 ft. lbs.) when reinstalling. You should lower the vehicle while following these steps to remove the battery and battery tray. Begin by disconnecting the positive battery cable retainer then remove the battery tray nut and bolt while tightening the bolt to 9 Nm (80 inch lbs.). The power distribution box can be placed aside after removing its 2 bolts and nut and pulling it upward to unclip the pushpin and disconnecting the 2 electrical connectors. To support the transaxle along with a suitable floor jack you must unscrew the four remaining bolts from the transaxle rear support insulator. Install new mount studs properly into their designated case seats followed by bolt tightening to 63 Nm (46 ft. lbs.) torque. First disconnect the clutch hydraulic line spring clip while continuing to lower the clutch line until it leaves the bracket. Then take off the clutch hydraulic line plastic retainer and transaxle mount. The installation process will be completed by performing the opposite steps of removal.

OEM Ford Fusion Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

52 Motor And Transmission Mounts found

View related parts
Ford Fusion Upper Arm
Part Number: F2GZ-6068-B
$99.37 MSRP: $144.65
You Save: $45.28 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Mount; Engine Torque Strut; Engine Support Rod; Transfer Case Mount; Motor Mount.; Transmission Mount; Torque Strut
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Front Mount, Passenger Side
Part Number: 6E5Z-6038-CK
$68.91 MSRP: $100.30
You Save: $31.39 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Manufacturer Note: Requires Multiple Replacment Parts
- Position: Front Passenger Side
- Replaced by: 9E5Z-6038-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS
View related parts
Ford Fusion Transmission Mount, Upper
Part Number: 9E5Z-6038-G
$83.50 MSRP: $121.55
You Save: $38.05 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount, Upper; Transfer Case Mount
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | S, SE, SEL | 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Front Mount
Part Number: 9E5Z-6038-F
$68.91 MSRP: $100.30
You Save: $31.39 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Motor Mount; Mount
- Replaces: 6E5Z-6038-CA, 6E5Z-6061-BA, 6E5Z-6038-CK
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | S, SE, SEL | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Ford Fusion Transmission Mount
Part Number: BE5Z-6038-C
$115.65 MSRP: $168.33
You Save: $52.68 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Transfer Case Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Fusion Transmission Mount, Driver Side
Part Number: 6H6Z-6038-BA
$80.12 MSRP: $116.62
You Save: $36.50 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Transfer Case Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Mount Bracket
Part Number: 9E5Z-6061-C
$48.60 MSRP: $72.78
You Save: $24.18 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Support; Engine Mount Bracket; Motor Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | S, SE, SEL | 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Transmission Mount, Lower
Part Number: F2GZ-6068-A
$89.47 MSRP: $137.68
You Save: $48.21 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Mount Torque Strut; Transfer Case Mount; Motor Mount; Torque Arm; Support Strut; Mount
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Transmission Mount
Part Number: 9E5Z-6038-A
$80.12 MSRP: $116.62
You Save: $36.50 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Manual Transmission Mount; Transfer Case Mount
- Replaces: 6E5Z-6038-CB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2012 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Upper Mount
Part Number: GG9Z-6068-B
$84.51 MSRP: $123.02
You Save: $38.51 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing - Transmission Extension; Manual Transmission Mount; Engine Mount Bracket; Motor Mount
- Replaces: DG9Z-6068-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | SE, SEL | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS
View related parts
Ford Fusion Front Mount
Part Number: 6E5Z-6038-DF
$111.64 MSRP: $162.50
You Save: $50.86 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: 6E5Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | SE, SEL | 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Front Mount
Part Number: DG9Z-6038-J
$103.28 MSRP: $150.33
You Save: $47.05 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Automatic Transmission Mount; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: DG9Z-6038-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | SE, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Fusion Front Mount
Part Number: BG9Z-6038-A
$74.75 MSRP: $108.80
You Save: $34.05 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: DS7Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | SE, SEL | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS
View related parts
Ford Fusion Transmission Mount
Part Number: GD9Z-6068-B
$104.79 MSRP: $152.53
You Save: $47.74 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Torque Strut
- Replaces: DS7Z-6068-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Fusion | SE | 4 Cyl 1.6 L GAS
View related parts
Ford Fusion Support Bracket
Part Number: DG9Z-6E042-B
$84.51 MSRP: $123.02
You Save: $38.51 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Mount Support Bracket; Engine Mount Bracket; Motor Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum Hybrid, S Hybrid, SE Hybrid, SEL Hybrid, Titanium Hybrid | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Fusion Support Bracket
Part Number: DP5Z-6F055-A
$30.35 MSRP: $44.18
You Save: $13.83 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Torque Strut; Support Rod; Mount; Transfer Case; Transmission; Motor; Transmission Mount Bracket; Torque Arm Bracket; Torque Strut Support Bracket; Torque Strut Bracket; Upper Arm Bracket
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Front Mount
Part Number: HP5Z-6038-B
$193.96 MSRP: $282.33
You Save: $88.37 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: HP5Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Fusion | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Support Bracket
Part Number: JG9Z-6E042-C
$67.13 MSRP: $97.72
You Save: $30.59 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Mount Support Bracket; Engine Mount Bracket; Motor Mount
- Replaces: DG9Z-6E042-C, DG9Z-6E042-A, HG9Z-6E042-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Front Mount
Part Number: HG9Z-6038-A
$153.43 MSRP: $223.33
You Save: $69.90 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, SE, SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Fusion Trans Mount Bracket Damper, Upper
Part Number: DG9Z-6F028-D
$40.18 MSRP: $58.48
You Save: $18.30 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Damper Assembly; Automatic Transmission Mount Insulator; Engine Mount Isolator, Upper; Transfer Case Mount; Motor Mount; Damper; Transmission Mount
- Position: Upper
- Replaces: DG9Z-6F028-C, DG9Z-6F028-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2020 Ford Fusion | Platinum, S, SE, SEL, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS

| Page 1 of 3 |Next >

1-20 of 52 Results

Ford Fusion Motor And Transmission Mount

Welcome to our website where you can discover high-quality, genuine Ford Fusion Motor And Transmission Mount. We offer an extensive inventory of OEM Ford Fusion Motor And Transmission Mount at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Ford Fusion Motor And Transmission Mount Parts Questions & Experts Answers

Transmission Mount Bracket, Driver Side
6E5Z-6031-GA
Q: How to Service and Repair the Rear Motor and Transmission Mount on Ford Fusion?
A: Start transaxle rear support insulator service and repair by hoisting the vehicle in NEUTRAL and then removing its splash shield bolts while you also detach the shield before reinstalling all bolts with 47 Nm (35 ft. lbs.) torque. Start by removing the 2 bolts at the bottom of the transaxle rear support insulator while torquing them to 63 Nm (46 ft. lbs.) when reinstalling. You should lower the vehicle while following these steps to remove the battery and battery tray. Begin by disconnecting the positive battery cable retainer then remove the battery tray nut and bolt while tightening the bolt to 9 Nm (80 inch lbs.). The power distribution box can be placed aside after removing its 2 bolts and nut and pulling it upward to unclip the pushpin and disconnecting the 2 electrical connectors. To support the transaxle along with a suitable floor jack you must unscrew the four remaining bolts from the transaxle rear support insulator. Install new mount studs properly into their designated case seats followed by bolt tightening to 63 Nm (46 ft. lbs.) torque. First disconnect the clutch hydraulic line spring clip while continuing to lower the clutch line until it leaves the bracket. Then take off the clutch hydraulic line plastic retainer and transaxle mount. The installation process will be completed by performing the opposite steps of removal.