How to Bleed the Brake System After Replacing the Front ABS Control Module on Ford Crown Victoria?

The first action for bleeding the brake system follows a sequence that starts with cleaning the brake master cylinder filler cap from dirt then filling the reservoir with specific brake fluid. Mount the clear waste line onto the RH rear bleeder screw while directing its other end into a container holding the recommended brake fluid. A maintenance specialist should tighten the RH rear bleeder screw when an assistant applies pressure to the brake pedal while a brake fluid stream runs out. Perform this procedure again until you see clear fluid coming out without bubbles in the brake master cylinder reservoir while you keep filling the reservoir. Complete the bleeding procedure by tightening the RH rear bleeder screw and removing its waste line and then follow with the bleeding sequence for the LH rear screw followed by the RH front disc brake caliper bleeder screw and ending with the LH front caliper bleeder screw. Attach the DCL cable adapter of the scan tool to the Data Link Connector under the dash then proceed with following the instructions on the tool. The system bleed procedure should be performed again following the previously described method.

How to Service and Repair the ABS Control Module on Ford Crown Victoria?

Service and repair of the Electronic Brake Control Module requires the first step to be air cleaner removal. The battery ground cable should be disconnected first. Start service of the Electronic Brake Control Module by first disconnecting the ABS module electrical connector followed by the hydraulic control unit (HCU) pump motor electrical connector. Thorough caution should be exercised when removing the module from the HCU because screws need to be removed in their correct order. When installing the module fasten all screws until they reach 3 Nm torque (27 inch lbs.). Clean surfaces on the ABS module and HCU gasket must be verified after the correct gasket installation while reversing the removal steps for reinstalling the components.

OEM Ford Crown Victoria ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 ABS Control Modules found

View related parts
Ford Crown Victoria Control Module Part Number: 9W7Z-2C219-A
$1105.88 MSRP: $1512.31
You Save: $406.43 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Ford Crown Victoria | Base, LWB, LX, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Motor & Pump Part Number: 9W7Z-2C346-B
Product Specifications
- Other Name: Module; ABS Pump And Motor Assembly; ABS Pump Assembly
- Replaces: 9W7Z-2C346-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Ford Crown Victoria | Base, LWB, LX, Police Interceptor | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Motor & Pump Part Number: 6W1Z-2C286-AA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics; ABS Pump And Motor Assembly; ABS Control Module; Control Assembly; ABS Pump Assembly
- Replaces: 1W1Z-2C286-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2008 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: 5W7Z-2C219-AB
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 6W7Z-2C219-BA, 5W7Z-2C219-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: XW7Z-2C219-AA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: w/ Traction assist
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: F8VZ-2C219-BA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU only, w/o Traction assist
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Motor & Pump Part Number: 6W7Z-2C286-BA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics; ABS Pump And Motor Assembly; ABS Pump Assembly
- Manufacturer Note: HCU, ABS Less Traction
- Replaces: 3W7Z-2C286-CC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2008 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: 5W1Z-2C219-AB
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU, Anti-Spin Traction Brakes W/O IVD
- Replaces: 6W1Z-2C219-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: 3W7Z-2C219-BB
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU, ABS Less Traction assist
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria ABS Pump Assembly Part Number: 1W7Z-2C286-AA
Product Specifications
- Other Name: Control; ABS Pump And Motor Assembly
- Manufacturer Note: Complete unit with bracket, ABS & TC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | Base, LWB, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: 1W7Z-2C219-BA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU, w/o Traction assist
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | Base, LWB, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: F6AZ-2C219-AA
Product Specifications
- Other Name: Module - ABS Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Ford Crown Victoria | Base, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: 1W7Z-2C219-AA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU, w/ Traction assist
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Crown Victoria | Base, LWB, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Control Module Part Number: 3W1Z-2C219-AA
$885.38 MSRP: $1210.77
You Save: $325.39 (27%)
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS

Ford Crown Victoria ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Ford Crown Victoria parts. We keep a wide inventory of OEM Crown Victoria parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Crown Victoria ABS Control Module is part of the anti-lock braking system of Ford Crown Victoria which is highly regarded for its dependability and power. It is important to know that this ABS Control Module is essential in a car to prevent wheel lock-ups during periods where there is intense braking thus improving the efficiency and safety of the car. ABS Control Module works with the help of a complex of wheel speed sensors, valves, a pump, and an ECU and it controls the wheel speed and brake pressure for optimal braking in needed conditions. Many designs of the Ford Crown Victoria have been released and used the ABS Control Module, enhancements feature the electronic stability control and traction control making the car more suitable to drive especially in contend situations. Separating the parts at the manufacturing stage to fit different versions of Crown Victoria means that drivers are promised these improvements, and the ABS Control Module sets the automobile industry apart. In addition to that, the Ford Crown Victoria is awarded in terms of durability by the same attribute as the ABS Control Module that not only enables the car to test stopping distances on most surfaces but also steer. Ranging from the body structure to the enhancive feature of the Ford Crown Victoria ABS Control Module, Ford has provided a vehicle that meets the high standards of safety and performance expected in the complex world of today's automobile business and this make Ford Crown Victoria ABS Control Module a vital component among the features of the ford Crown Victoria set.

Ford Crown Victoria ABS Control Module Parts and Q&A

Control Module
XW7Z-2C219-AA
Q: How to Bleed the Brake System After Replacing the Front ABS Control Module on Ford Crown Victoria?
A:
The first action for bleeding the brake system follows a sequence that starts with cleaning the Brake Master Cylinder filler cap from dirt then filling the reservoir with specific brake fluid. Mount the clear waste line onto the RH rear bleeder screw while directing its other end into a container holding the recommended brake fluid. A maintenance specialist should tighten the RH rear bleeder screw when an assistant applies pressure to the brake pedal while a brake fluid stream runs out. Perform this procedure again until you see clear fluid coming out without bubbles in the brake master cylinder reservoir while you keep filling the reservoir. Complete the bleeding procedure by tightening the RH rear bleeder screw and removing its waste line and then follow with the bleeding sequence for the LH rear screw followed by the RH front disc brake caliper bleeder screw and ending with the LH front caliper bleeder screw. Attach the DCL cable adapter of the scan tool to the Data Link Connector under the dash then proceed with following the instructions on the tool. The system bleed procedure should be performed again following the previously described method.
Motor & Pump
6W1Z-2C286-AA
Q: How to Service and Repair the ABS Control Module on Ford Crown Victoria?
A:
Service and repair of the Electronic Brake Control Module requires the first step to be air cleaner removal. The battery ground cable should be disconnected first. Start service of the Electronic Brake Control Module by first disconnecting the ABS module electrical connector followed by the hydraulic control unit (HCU) pump motor electrical connector. Thorough caution should be exercised when removing the module from the HCU because screws need to be removed in their correct order. When installing the module fasten all screws until they reach 3 Nm torque (27 inch lbs.). Clean surfaces on the ABS module and HCU gasket must be verified after the correct gasket installation while reversing the removal steps for reinstalling the components.