How to Service and Repair an ABS Control Module in the Hydraulic Control Assembly on Ford E-150?

The hydraulic control assembly service begins with disconnecting the battery ground cable. Securely detach the degas bottle by removing its three bolts and place it aside after tightening the bolts to 10 Nm (89 inch lbs.) during reinstall. When servicing vehicles with the 6.0L engine you must not remove the power steering fluid reservoir hoses. Instead, remove the four bolts then place both reservoir and bracket to the side tightening them to 28 Nm (21 ft. lbs.) at reinstallation. Workers should fully detach the power steering fluid reservoir from 4.6L, 5.4L or 6.0L engines before placing the reservoir aside. When disconnecting brake tube fittings from the brake master cylinder reinstallation requires tightening them to 19 Nm (14 ft. lbs.). Each port on the hydraulic control unit (HCU) needs a plug before removal of the three brake tube fittings from the HCU while tightening these fittings to 20 Nm (15 ft. lbs.) upon proper reinstallation. Tighten both extra brake tube fittings to 17 Nm (13 ft. lbs.) after reattaching them. First disconnect the ABS module electrical connector before you remove the HCU bracket to inner fender well nuts to extract the HCU assembly and tighten it to 29 Nm (21 ft. lbs.) during reinstallation. Remove ABS module screws from the HCU before installation but tighten them to 5 Nm (44 inch lbs.) strength. After installing the HCU return to the reverse removal sequence while performing a bleeding process of the HCU. Only use DOT 3 motor vehicle brake fluid which is approved by DOT because permanent brake component damage can occur and you must prevent direct fluid contact on eyes and painted or plastic materials.

How to properly bleed the brake system after installing a new ABS Control Module on Ford E-150?

The brake system needs bleeding during installation of new Hydraulic Control Units and all upstream components starting with the HCU or continuing further upstream. Follow Pressure Bleeding or Manual Bleeding and then finish the bleed operation using the required bleeding method. The most effective bleeding method is pressure bleeding according to recommendations. The next step requires connection of the scan tool for execution of the ABS Service Bleed procedure. Repetition of the Pressure Bleeding or Manual Bleeding methods should follow to guarantee complete bleeding of the system.

OEM Ford E-150 ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 ABS Control Modules found

View related parts
Ford E-150 Control Module Part Number: 9C2Z-2C219-G
$515.04 MSRP: $693.85
You Save: $178.81 (26%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 9C2Z-2C219-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Modulator Valve Part Number: 9C2Z-2C215-A
$904.61 MSRP: $1237.08
You Save: $332.47 (27%)
ADD TO CART
Product Specifications
- Other Name: Module; ABS Control Module; ABS Control Unit
- Replaces: 8C2Z-2C286-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Modulator Valve Part Number: 9C2Z-2C215-B
$548.40 MSRP: $793.69
You Save: $245.29 (31%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Module; ABS Control Module; ABS Control Unit
- Replaces: 8C2Z-2C286-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Control Module Part Number: BC2Z-2C219-A
$513.79 MSRP: $692.15
You Save: $178.36 (26%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2014 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Control Valve Part Number: 7C2Z-2C219-CA
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 6C2Z-2C219-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-150 | Base, Chateau, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Modulator Valve Part Number: 6C2Z-2C286-CA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Replaces: 2C2Z-2C286-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-150 | Base, Chateau, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Modulator Valve Part Number: 6C2Z-2C286-BA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-150 | Base, Chateau, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Speed Sensor Part Number: 6L3Z-2B373-A
$774.00 MSRP: $1058.46
You Save: $284.46 (27%)
Product Specifications
- Other Name: Valve Assembly - Modulator; ABS Hydraulic Assembly; Control Valve; Control Module; Modulator Valve
- Replaces: XL3Z-2B373-BARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford E-150 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Control Valve Part Number: 8C2Z-2C219-CG
$417.51 MSRP: $563.08
You Save: $145.57 (26%)
Product Specifications
- Other Name: Control; ABS Control Module; Control Module
- Replaces: 8C2Z-2C219-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Control Module Part Number: XC2Z-2B373-AA
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford E-150 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Control Valve Part Number: 8C2Z-2C219-A
Product Specifications
- Other Name: Control; ABS Control Module; Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Control Valve Part Number: 7C2Z-2C219-FA
Product Specifications
- Other Name: Control; ABS Control Module; Control Module
- Replaces: 6C2Z-2C219-FA, 6C2Z-2C219-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford E-150 | Base, Chateau, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford E-150 Control Module Part Number: AC2Z-2C219-A
$499.23 MSRP: $673.85
You Save: $174.62 (26%)
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2010 Ford E-150 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L LPG
View related parts
Ford E-150 Control Valve Part Number: 3C2Z-2C286-AARM
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford E-150 | Base | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS

Ford E-150 ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Ford E-150 parts. We keep a wide inventory of OEM E-150 parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

It has been noted that the ABS Control Module plays an important role in the series of Ford E-150 vehicles famed for their efficiency and durability of the part in controlling the anti-lock braking system. This high-class ABS Control Module makes sure that the wheels of the car are not locked during the process of hard braking and enhances the safety of a vehicle as it reduces the chances of skidding. The ABS Control Module works together with the cluster of Wheel speed sensors, valves, a Pump, and an Electronic Control Unit or ECU that modifies the braking power as per the real-time data received from these devices. The companies integrated this system not only for better control, but for minimizing the stopping distances, that's why since 1957 many E-150 models were equipped with this option. The Ford E-150 vehicle model has gone through many generations, and so has the ABS Control Module that has adopted features such as the ESC and traction control. These enhancements build up the Ford E-150's safety and efficiency especially in tough road situations. Selecting the ABS Control Module in the automotive market simplified because of the customer recognition of its durability and importance for enhancing the braking system. ABS Control Module is suitable for multiple E-150 models The ABS Control Module testifies to the company's aim of providing vehicle that enhances the safety of drivers on the road while at the same ensuring that the vehicle is operational and efficient, this makes the Ford E-150 a reliable vehicle for consumers out there in the market.

Ford E-150 ABS Control Module Parts and Q&A

Modulator Valve
6C2Z-2C286-CA
Q: How to Service and Repair an ABS Control Module in the Hydraulic Control Assembly on Ford E-150?
A:
The hydraulic control assembly service begins with disconnecting the battery ground cable. Securely detach the degas bottle by removing its three bolts and place it aside after tightening the bolts to 10 Nm (89 inch lbs.) during reinstall. When servicing vehicles with the 6.0L engine you must not remove the power steering fluid reservoir hoses. Instead, remove the four bolts then place both reservoir and bracket to the side tightening them to 28 Nm (21 ft. lbs.) at reinstallation. Workers should fully detach the power steering fluid reservoir from 4.6L, 5.4L or 6.0L engines before placing the reservoir aside. When disconnecting brake tube fittings from the Brake Master Cylinder reinstallation requires tightening them to 19 Nm (14 ft. lbs.). Each port on the hydraulic control unit (HCU) needs a plug before removal of the three brake tube fittings from the HCU while tightening these fittings to 20 Nm (15 ft. lbs.) upon proper reinstallation. Tighten both extra brake tube fittings to 17 Nm (13 ft. lbs.) after reattaching them. First disconnect the ABS module electrical connector before you remove the HCU bracket to inner fender well nuts to extract the HCU assembly and tighten it to 29 Nm (21 ft. lbs.) during reinstallation. Remove ABS module screws from the HCU before installation but tighten them to 5 Nm (44 inch lbs.) strength. After installing the HCU return to the reverse removal sequence while performing a bleeding process of the HCU. Only use DOT 3 motor vehicle brake fluid which is approved by DOT because permanent brake component damage can occur and you must prevent direct fluid contact on eyes and painted or plastic materials.
Modulator Valve
9C2Z-2C215-A
Q: How to properly bleed the brake system after installing a new ABS Control Module on Ford E-150?
A:
The brake system needs bleeding during installation of new Hydraulic Control Units and all upstream components starting with the HCU or continuing further upstream. Follow Pressure Bleeding or Manual Bleeding and then finish the bleed operation using the required bleeding method. The most effective bleeding method is pressure bleeding according to recommendations. The next step requires connection of the scan tool for execution of the ABS Service Bleed procedure. Repetition of the Pressure Bleeding or Manual Bleeding methods should follow to guarantee complete bleeding of the system.