How to remove and replace the Engine Control Module (ECM) on Ford Edge?

The Powertrain Control Module (PCM) replacement process does not demand new keys nor key programming because of its procedure. The procedure for Programmable Module Installation brings the needed module configuration during this initial stage. Three PCM electrical connections need to be disconnected before using tools to remove the two PCM nuts while carefully extracting the PCM along with its gasket from the vehicle. The process begins with gasket and PCM positioning then proceed to install the two PCM nuts while torqueing them to 5 Nm (44 lb-in). Secure the PCM by replugging the three electrical connectors. The restoration includes completing the steps in the Programmable Module Installation procedure while executing the Parameter Reset procedure to reprogram the passive anti-theft system (PATS).

What are the key features and functions of the Engine Control Module (ECM) and its integrated EEPROM regarding strategy and calibration information on Ford Edge?

The Engine Control Module (Ecm) uses an Electrically Erasable Programmable Read Only Memory (Eeprom) that exists inside the powertrain control module (Pcm) to store vehicle-specific calibration data for programming or flashing multiple times. A new Pcm needs a programmed vehicle identification (Vid) block because a lack of this step leads to possible diagnostic trouble codes (Dtc) P1635 or P1639. Making improper changes to the Vid block since production might activate Dtc P1635 or reveal an incorrect tire/axle ratio which stands as a typical Dtc P1639 cause. Among essential Vin information in the Vid block stands the vehicle identification number (Vin), alongside octane adjust, fuel type, vehicle speed limit, tire size, axle ratio and speed control versus electronic shift-on-the-fly (EssoF) and manual shift-on-the-fly (MsoF). The range limits on tire and axle ratios exist within the Vid block so a notification will appear when the reconfiguration limit reaches its threshold prior to requiring Pcm flash procedure. To activate misfire monitor functionality on vehicles with Dtc permanent reporting, technicians must perform learning of the neutral profile after Pcm replacement through the Misfire Monitor Neutral Profile Learn function available on the scan tool. The learning process must be performed whenever there is a Pcm or crankshaft position (Ckp) sensor change or major engine work takes place. The verification of neutral profile learning completion requires an inspection of the Mp Lrn Pid with a scan tool which should display Yes after completion. The Vid block of a new Pcm contains no programmed data so it must be populated either by transferring data from another Pcm or by manual data entry because of Pcm damage. The process requires a suitable scan tool to enter parameters which must include accurate tire information at revolutions per mile together with axle ratio and 4x4/4x2 settings to prevent the appearance of Dtc P1635 and P1639. The As-Built Data Center should be contacted by technicians for manual updates when either old Pcm is undependable or data is inaccessible. Ford and Lincoln Mercury service center technicians obtain As-Built data through the National Hotline or Pts website although non-Ford technicians benefit from Motorcraft® website access. Alterations to the Vid block must occur to match vehicle hardware and full Eeprom reprogramming is essential when implementing strategy or calibration updates or when resetting the Vid block because of its maximum usage requirement.

OEM Ford Edge Engine Control Module

Engine Control Computer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

59 Engine Control Modules found

View related parts
Ford Edge PCM Part Number: DT4Z-12A650-BDB
$525.51 MSRP: $771.67
You Save: $246.16 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module; ECM
- Replaces: DT4Z-12A650-BDA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Edge | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Edge PCM Part Number: DT4Z-12A650-ASD
$606.38 MSRP: $898.33
You Save: $291.95 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Module - Engine Control - Eec V
- Replaces: DT4Z-12A650-ASC, DT4Z-12A650-ASB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013 Ford Edge | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Edge PCM Part Number: BT4Z-12A650-BTB
$423.36 MSRP: $621.67
You Save: $198.31 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Replaces: BT4Z-12A650-BTA, BT4Z-12A650-AGD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Ford Edge | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Edge PCM Part Number: DT4Z-12A650-BHA
$542.25 MSRP: $803.33
You Save: $261.08 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Edge | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Edge PCM Part Number: BT4Z-12A650-APB
$634.84 MSRP: $940.50
You Save: $305.66 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Replaces: BT4Z-12A650-EJ, BT4Z-12A650-APA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2013 Ford Edge | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Edge ECM Part Number: DT4Z-12A650-ALD
$455.14 MSRP: $668.33
You Save: $213.19 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Module - Engine Control - Eec V; Engine Control Module
- Replaces: DT4Z-12A650-ALC, DT4Z-12A650-ALB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013 Ford Edge | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Edge PCM Part Number: BT4Z-12A650-BUB
$423.36 MSRP: $621.67
You Save: $198.31 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Replaces: BT4Z-12A650-BUA, BT4Z-12A650-AHD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Ford Edge | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Edge PCM Part Number: DT4Z-12A650-AND
$606.38 MSRP: $898.33
You Save: $291.95 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Module - Engine Control - Eec V
- Replaces: DT4Z-12A650-ANC, DT4Z-12A650-ANB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013 Ford Edge | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Edge PCM Part Number: DT4Z-12A650-BJB
$563.63 MSRP: $835.00
You Save: $271.37 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module; ECM
- Replaces: DT4Z-12A650-BJA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Edge | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Edge PCM Part Number: BT4Z-12A650-BHB
$527.78 MSRP: $775.00
You Save: $247.22 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Replaces: BT4Z-12A650-AMD, BT4Z-12A650-BHA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2013 Ford Edge | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Edge PCM Part Number: DT4Z-12A650-BMB
$563.63 MSRP: $835.00
You Save: $271.37 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module; ECM; Module - Engine Control - Eec V
- Replaces: DT4Z-12A650-BMA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Edge | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Edge PCM Part Number: BT4Z-12A650-BNB
$423.36 MSRP: $621.67
You Save: $198.31 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Replaces: BT4Z-12A650-BNA, BT4Z-12A650-ACD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Ford Edge | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Edge PCM Part Number: BT4Z-12A650-BKB
$423.36 MSRP: $621.67
You Save: $198.31 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Replaces: BT4Z-12A650-AAD, BT4Z-12A650-BKA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2013 Ford Edge | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Edge PCM Part Number: K2GZ-12A650-CDANP
$368.88 MSRP: $541.67
You Save: $172.79 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module; ECM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2024 Ford Edge | ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge PCM Part Number: DT4Z-12A650-AKD
$561.38 MSRP: $831.67
You Save: $270.29 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Replaces: DT4Z-12A650-AKC, DT4Z-12A650-AKB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013 Ford Edge | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Edge PCM Part Number: 7U7Z-12A650-HFARM
$664.40 MSRP: $984.30
You Save: $319.90 (33%)
ADD TO CART
Product Specifications
- Other Name: Reman Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module; ECM
- Replaces: 7T4Z-12A650-ZH, 7U7Z-12A650-HHA, 7T4Z-12A650-VH, 7U7Z-12A650-HKA, 7U7Z-12A650-HMA, 7T4Z-12A650-XH, 7T4Z-12A650-ABH, 7U7Z-12A650-HFA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Edge | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Edge PCM Part Number: BT4Z-12A650-BJB
$423.36 MSRP: $621.67
You Save: $198.31 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Replaces: BT4Z-12A650-AND, BT4Z-12A650-BJA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2013 Ford Edge | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Edge PCM Part Number: DT4Z-12A650-AJD
$561.38 MSRP: $831.67
You Save: $270.29 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Replaces: DT4Z-12A650-AJB, DT4Z-12A650-AJC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013 Ford Edge | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Edge PCM Part Number: DT4Z-12A650-BKB
$563.63 MSRP: $835.00
You Save: $271.37 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); Engine Control Module; ECM; Module - Engine Control - Eec V
- Replaces: DT4Z-12A650-BKA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Edge | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Edge PCM Part Number: DT4Z-12A650-BGA
$439.25 MSRP: $645.00
You Save: $205.75 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Control - EEC; Engine Control Module (ECM); ECM; Module - Engine Control - Eec V; Engine Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Edge | Sport | 6 Cyl 3.7 L GAS

| Page 1 of 3 |Next >

1-20 of 59 Results

Ford Edge Engine Control Module

OEM Engine Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Engine Control Module with long life and a perfect fit. Come to our website and find genuine Ford Edge parts. We keep a wide inventory of OEM Edge parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Thus, thousands of 'smart' engineered modules like the Engine Control Module are the ways Ford has proven that it means business when pushing out Edge models. Being one of the main control units of any vehicle, Engine Control Module is responsible for the proper functioning of all the processes taking place in the car's engine, including the air-fuel ratio and the ignition timing. Besides, boosting the performance of the Ford Edge, this advanced ECM is also responsible for the safety aspects of the vehicle by controlling the powertrain effectively. This ingenious part fits Series 4 Ford Edge (2018-present) models compatible with different Edge engine types; base SE, sporty ST, and luxurious SEL trims come with different engine types; 2.0-liter turbocharged four-cylinder, twin-turbocharged V6 among others. The use of engines' Engine Control Module starting from the initial integrated circuit to the current microprocessor based systems is a clear example of the Ford Edge's aspects in the contemporary cars technology for performance tuning. Realtim data processing and adaptve control strategies make the ford edge engine control module unique in automotive market, insomuch as it enables drivers to achieve smooth take offs and maximum fuel economy. Engine Control Module is a significant and well-established feature of its model; it increases its sturdiness and uses the newest technology, which makes the Ford Edge reliable for families and performance lovers.

Ford Edge Engine Control Module Parts and Q&A

PCM
7U7Z-12A650-HFARM
Q: How to remove and replace the Engine Control Module (ECM) on Ford Edge?
A:
The Powertrain Control Module (PCM) replacement process does not demand new keys nor key programming because of its procedure. The procedure for Programmable Module Installation brings the needed module configuration during this initial stage. Three PCM electrical connections need to be disconnected before using tools to remove the two PCM nuts while carefully extracting the PCM along with its gasket from the vehicle. The process begins with gasket and PCM positioning then proceed to install the two PCM nuts while torqueing them to 5 Nm (44 lb-in). Secure the PCM by replugging the three electrical connectors. The restoration includes completing the steps in the Programmable Module Installation procedure while executing the Parameter Reset procedure to reprogram the passive anti-theft system (PATS).
PCM
7U7Z-12A650-HNARM
Q: What are the key features and functions of the Engine Control Module (ECM) and its integrated EEPROM regarding strategy and calibration information on Ford Edge?
A:
The Engine Control Module (Ecm) uses an Electrically Erasable Programmable Read Only Memory (Eeprom) that exists inside the powertrain control module (Pcm) to store vehicle-specific calibration data for programming or flashing multiple times. A new Pcm needs a programmed vehicle identification (Vid) block because a lack of this step leads to possible diagnostic trouble codes (Dtc) P1635 or P1639. Making improper changes to the Vid block since production might activate Dtc P1635 or reveal an incorrect tire/axle ratio which stands as a typical Dtc P1639 cause. Among essential Vin information in the Vid block stands the vehicle identification number (Vin), alongside octane adjust, fuel type, vehicle speed limit, tire size, axle ratio and speed control versus electronic shift-on-the-fly (EssoF) and manual shift-on-the-fly (MsoF). The range limits on tire and axle ratios exist within the Vid block so a notification will appear when the reconfiguration limit reaches its threshold prior to requiring Pcm flash procedure. To activate misfire monitor functionality on vehicles with Dtc permanent reporting, technicians must perform learning of the neutral profile after Pcm replacement through the Misfire Monitor Neutral Profile Learn function available on the scan tool. The learning process must be performed whenever there is a Pcm or crankshaft position (Ckp) sensor change or major engine work takes place. The verification of neutral profile learning completion requires an inspection of the Mp Lrn Pid with a scan tool which should display Yes after completion. The Vid block of a new Pcm contains no programmed data so it must be populated either by transferring data from another Pcm or by manual data entry because of Pcm damage. The process requires a suitable scan tool to enter parameters which must include accurate tire information at revolutions per mile together with axle ratio and 4x4/4x2 settings to prevent the appearance of Dtc P1635 and P1639. The As-Built Data Center should be contacted by technicians for manual updates when either old Pcm is undependable or data is inaccessible. Ford and Lincoln Mercury service center technicians obtain As-Built data through the National Hotline or Pts website although non-Ford technicians benefit from Motorcraft® website access. Alterations to the Vid block must occur to match vehicle hardware and full Eeprom reprogramming is essential when implementing strategy or calibration updates or when resetting the Vid block because of its maximum usage requirement.