How to Service and Repair the Yaw Sensor on Ford Explorer?

The first step for yaw rate sensor maintenance requires removal of the pin-type retainer along with the left-hand floor console finish panel. The left-hand instrument panel brace requires removal of its two bolts and two nuts before installation where you must use 9 Nm (80 lb-in) torque setting. You should first disconnect the electrical connector from the stability control sensor cluster then remove two floor heater duct bolts on the left side. Disassemble each electrical harness retainer connected to the stability control sensor cluster and place the parts to the side. Loosen the two stability control sensor cluster bracket nuts to access the stability control sensor cluster which should be removed before reinstallation by securing the nuts to 7 Nm (62 lb-in). The installation ends with performing the steps in reverse order to ensure all components are tightly implemented. The installation of new stability control sensor clusters requires ABS module calibration through scan tool instructions.

OEM Ford Explorer Yaw Sensor

Yaw Rate Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Yaw Sensors found

View related parts
Ford Explorer Yaw Rate Sensor
Part Number: 7L1Z-3C187-A
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Steering Wheel Speed Sensor; Yaw Sensor; Sensor
- Manufacturer Note: Lateral/Yaw Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Explorer | Eddie Bauer, Limited, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Yaw Rate Sensor
Part Number: 6L2Z-3C187-AA
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Steering Wheel Speed Sensor; Yaw Sensor; Sensor
- Manufacturer Note: Lateral/Yaw Sensor
- Replaces: 3C5Z-3C187-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Explorer | Eddie Bauer, Limited, NBX, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Yaw Rate Sensor
Part Number: 3L2Z-3C296-BA
Product Specifications
- Other Name: Sensor Assembly
- Manufacturer Note: Sensor - Yaw
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Ford Explorer | Eddie Bauer, Limited, NBX, Postal, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Sensor
Part Number: 3L2Z-3C187-AA
Product Specifications
- Other Name: Sensor Assembly; ABS Deceleration Sensor; Suspension Yaw Sensor; Steering Wheel Speed Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Ford Explorer | Eddie Bauer, Limited, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Yaw Rate Sensor
Part Number: 3L2Z-3C296-AA
Product Specifications
- Other Name: Sensor Assembly
- Manufacturer Note: Sensor - Yaw
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Ford Explorer | Eddie Bauer, Limited, NBX, Postal, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS

Ford Explorer Yaw Sensor

Welcome to our website where you can discover high-quality, genuine Ford Explorer Yaw Sensor. We offer an extensive inventory of OEM Ford Explorer Yaw Sensor at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Ford Explorer Yaw Sensor Parts Questions & Experts Answers

Yaw Rate Sensor
7L1Z-3C187-A
Q: How to Service and Repair the Yaw Sensor on Ford Explorer?
A: The first step for yaw rate sensor maintenance requires removal of the pin-type retainer along with the left-hand floor console finish panel. The left-hand instrument panel brace requires removal of its two bolts and two nuts before installation where you must use 9 Nm (80 lb-in) torque setting. You should first disconnect the electrical connector from the stability control sensor cluster then remove two floor heater duct bolts on the left side. Disassemble each electrical harness retainer connected to the stability control sensor cluster and place the parts to the side. Loosen the two stability control sensor cluster bracket nuts to access the stability control sensor cluster which should be removed before reinstallation by securing the nuts to 7 Nm (62 lb-in). The installation ends with performing the steps in reverse order to ensure all components are tightly implemented. The installation of new stability control sensor clusters requires ABS module calibration through scan tool instructions.