How Should the Side Airbag Curtain Module Be Serviced and Repaired to Ensure Safety and Proper Installation on Ford Focus?

You need to keep a Safety Canopy® with its tear seam facing away from your body when servicing or repairing the side air curtain module to prevent fatal injuries caused by accidental deployment. Any vehicle with Safety Canopy® or side air curtain modules must display the word air bag on the headliner when it touches each B-pillar trim section or deployment risks will occur. After Safety Canopy® or side air curtain module deployment you need to replace the headliner and new A-, B-, C-pillar upper trim panels and attaching hardware while removing damaged components to stop potential incorrect deployment. Perform inspection of Safety Canopy® or side air curtain module before the installation process begins; if damage is present and module protection is compromised, conduct a replacement immediately. The proper deployment can be hindered by any deployment path obstruction or fasteners used around the module area. A damage check of the roofline needs to occur before any installation process together with necessary restoration work on the original condition. Prior to vehicle release the air bag warning indicator will light up when the correct Restraints Control Module (RCM) fuse is removed in the ON ignition state along with complete Supplemental Restraint System (SRS) operation being necessary. Start by taking out the headliner and de-energize the SRS system while folding the rear seat backrests down and removing pin-type retainers followed by lifting the parcels shelf. To begin disconnect the electrical connector of the side air curtain module and uninstall both the tether bracket front bolt and pin retainers from the A-pillar trim bracket. The processes include separating the side air curtain module bolt from its A-pillar trim bracket where technicians need to use new torque-prevailing type J-nuts for effective fastener attachment. Begin by unscrewing the middle and rear bolts fastening the side air curtain module then remove the two rear bracket bolts before taking out the module by pulling it toward the vehicle front. The installation process finishes by putting back the SRS system power and reinstalling the headliner while performing the opposite steps of removal. The installation requires torque at 14 Nm which corresponds to 124 pound-inches for all bolts.

How to remove and replace the side Airbag module safely on Ford Focus?

Safety glasses should always be worn when handling side air bag modules to prevent injuries from potential accidental activation. The connectors on the air bag module need to be avoided because probing could result in a deployment incident with personal injury risk for you. Memory saver devices should never be used because they fail to minimize injury risks. A seat with a seat-mounted side air bag along with a safety belt pretensioner requires you to first depower the supplemental restraint system. There is no SRS fault when the air bag warning lamp illuminates because the RCM fuse has been removed during this test cycle. A complete inspection of the SRS operational readiness and lack of faults must occur before any vehicle return to its customer. The first step entails depowering the system before removing the front seat backrest component. Make note of the wiring harness location since a wrong route could lead to damages from seat movement. Use a tool to disconnect the side air bag module wiring harness from the seat frame through the detaching retaining clip. Pull out the side air bag module after removing its retaining nuts and discard these nuts. A side air bag module always requires left-hand or right-hand orientation depending on the seat choice and wire harnesses should rest against the seat base after installation. Use new self-locking nuts to complete the installation by reverting the uninstallation steps. Finally, repower the system.

OEM Ford Focus Airbag

Air Bag Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

60 Airbags found

View related parts
Ford Focus Passenger Air Bag, Upper Part Number: F1EZ-58044A74-A
$842.99 MSRP: $1248.87
You Save: $405.88 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag; Instrument Panel Air Bag, Upper; Passenger Inflator Module
- Position: Upper Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Focus | Electric, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)
View related parts
Ford Focus Driver Inflator Module Part Number: F1EZ-58043B13-AH
$271.25 MSRP: $398.32
You Save: $127.07 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module; Steering Wheel Air Bag; Driver Air Bag
- Position: Driver Side
- Replaces: F1EZ-58043B13-AD, F1EZ-58043B13-AC, F1EZ-58043B13-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2018 Ford Focus | Electric, RS, RS Version, S, SE, SEL, Series 20, SERIES 32, Series 40, Series 70, Series 75, Series 80, ST, ST-Line, Titamium, Titanium, Titanium Econetic, Trend Econetic, ZTW | 1.0L L3, 2.0L L4, 2.3L L4, 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, EV
View related parts
Ford Focus Side Impact Inflator Module, Driver Side Part Number: G1EZ-99611D11-A
$314.96 MSRP: $462.50
You Save: $147.54 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Ford Focus | RS | 4 Cyl 2.3 L GAS
View related parts
Ford Focus Knee Inflator Module, Lower Driver Side Part Number: DM5Z-78045J77-AA
$534.60 MSRP: $785.02
You Save: $250.42 (32%)
ADD TO CART
Product Specifications
- Other Name: Air Bag; Instrument Panel Air Bag, Left Lower; Knee Air Bag
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | Electric, RS, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, BATTERY EV (EV/BEV)
View related parts
Ford Focus Knee Inflator Module, Charcoal Black, Lower Driver Side Part Number: G1EZ-78045J77-AA
$658.29 MSRP: $975.25
You Save: $316.96 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Air Bag; Instrument Panel Air Bag, Left Lower; Knee Air Bag
- Manufacturer Note: Air Bag - Knee
- Position: Driver Side
- Replaces: DM5Z-78045J77-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | Electric, RS, S, SE, SEL, ST, Titamium, Titanium | 1.0L L3, 2.0L L4, 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, BATTERY EV (EV/BEV), EV
View related parts
Ford Focus Inflator Curtain, Passenger Side Part Number: 9S4Z-54042D94-A
$450.45 MSRP: $623.16
You Save: $172.71 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag; Curtain Air Bag, Right; Head Air Bag
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Ford Focus | S, SE, SEL, SES | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Driver Inflator Module Part Number: DM5Z-58043B13-DA
$492.79 MSRP: $772.63
You Save: $279.84 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module; Steering Wheel Air Bag; Driver Air Bag
- Position: Driver Side
- Replaces: CP9Z-58043B13-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | Electric, S, SE, SEL, ST, Titamium, Titanium | 2.0L L4, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV), EV
View related parts
Ford Focus Inflator Curtain, Driver Side Part Number: DM5Z-54042D95-B
$601.65 MSRP: $891.33
You Save: $289.68 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag; Curtain Air Bag, Left, Right; Head Air Bag
- Position: Driver Side
- Replaces: DM5Z-54042D95-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2016 Ford Focus | Electric, RS, S, SE, SEL, ST, Titamium, Titanium | 1.0L L3, 2.0L L4, 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, BATTERY EV (EV/BEV), EV
View related parts
Ford Focus Inflator Curtain, Passenger Side Part Number: CP9Z-54042D95-A
$623.71 MSRP: $924.02
You Save: $300.31 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag; Curtain Air Bag, Left, Right; Head Air Bag
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012 Ford Focus | Electric, S, SE, SEL, Titanium | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)
View related parts
Ford Focus Inflator Curtain, Driver Side Part Number: DM5Z-54042D94-B
$697.42 MSRP: $1033.22
You Save: $335.80 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag; Curtain Air Bag, Left, Right; Head Air Bag
- Position: Driver Side
- Replaces: DM5Z-54042D94-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2016 Ford Focus | Electric, RS, S, SE, SEL, ST, Titamium, Titanium | 1.0L L3, 2.0L L4, 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, BATTERY EV (EV/BEV), EV
View related parts
Ford Focus Side Impact Inflator Module, Front Driver Side Part Number: F1EZ-99611D11-B
$71.99 MSRP: $104.78
You Save: $32.79 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag; Seat Air Bag, Front Left; Front Seat Air Bag
- Position: Driver Side
- Replaces: F1EZ-99611D11-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Focus | Electric, RS, S, SE, SEL, ST, Titamium, Titanium | 1.0L L3, 2.0L L4, 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, BATTERY EV (EV/BEV), EV
View related parts
Ford Focus Side Impact Inflator Module, Front Passenger Side Part Number: F1EZ-99611D10-B
$74.23 MSRP: $108.05
You Save: $33.82 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag; Seat Air Bag, Front Right; Front Seat Air Bag
- Position: Passenger Side
- Replaces: F1EZ-99611D10-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Focus | Electric, RS, S, SE, SEL, ST, Titamium, Titanium | 1.0L L3, 2.0L L4, 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, BATTERY EV (EV/BEV), EV
View related parts
Ford Focus Inflator Curtain, Driver Side Part Number: GM5Z-54042D95-B
$164.43 MSRP: $239.35
You Save: $74.92 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Curtain Assembly; Curtain Air Bag, Left; Head Air Bag
- Position: Driver Side
- Replaces: GM5Z-54042D95-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Ford Focus | Electric, RS, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, BATTERY EV (EV/BEV)
View related parts
Ford Focus Inflator Curtain, Passenger Side Part Number: GM5Z-54042D94-B
$164.43 MSRP: $239.35
You Save: $74.92 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Curtain Assembly; Curtain Air Bag, Right; Head Air Bag
- Position: Passenger Side
- Replaces: GM5Z-54042D94-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Ford Focus | Electric, RS, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, BATTERY EV (EV/BEV)
View related parts
Ford Focus Side Impact Inflator Module, Passenger Side Part Number: G1EZ-99611D10-A
$314.96 MSRP: $462.50
You Save: $147.54 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Ford Focus | RS | 4 Cyl 2.3 L GAS
View related parts
Ford Focus Driver Inflator Module Part Number: DM5Z-58043B13-CA
$514.20 MSRP: $755.07
You Save: $240.87 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module; Steering Wheel Air Bag; Driver Air Bag
- Position: Driver Side
- Replaces: CP9Z-58043B13-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | Electric, RS, S, SE, SEL, ST, Titamium, Titanium | 2.0L L4, 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, BATTERY EV (EV/BEV), EV
View related parts
Ford Focus Inflator Curtain, Passenger Side Part Number: 8S4Z-63042D94-A
$57.33 MSRP: $79.32
You Save: $21.99 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag; Curtain Air Bag, Right; Head Air Bag
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford Focus | S, SE, SES | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Driver Air Bag Part Number: YS4Z-54043B13-AAA
$77.01 MSRP: $106.54
You Save: $29.53 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Air Bag; Steering Wheel Air Bag
- Manufacturer Note: (,H*) , Medium Parchment (use W713191,S900 to attach 043B13 to 3600) , with speed control
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2001 Ford Focus | LX, SE, Sony Limited Edition, ZTS, ZX3 | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Driver Inflator Module Part Number: EM5Z-58043B13-BA
Product Specifications
- Other Name: Module
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2015 Ford Focus | S, SE, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
View related parts
Ford Focus Inflator Curtain, Driver Side Part Number: CP9Z-54042D94-A
Product Specifications
- Other Name: Module - Air Bag; Curtain Air Bag, Left, Right; Head Air Bag
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012 Ford Focus | Electric, S, SE, SEL, Titanium | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)

| Page 1 of 3 |Next >

1-20 of 60 Results

Ford Focus Airbag

OEM Airbag boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Airbag with long life and a perfect fit. Come to our website and find genuine Ford Focus parts. We keep a wide inventory of OEM Focus parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Focus Airbag Parts and Q&A

Inflator Curtain, Passenger Side
9S4Z-54042D94-A
Q: How Should the Side Airbag Curtain Module Be Serviced and Repaired to Ensure Safety and Proper Installation on Ford Focus?
A:
You need to keep a Safety Canopy® with its tear seam facing away from your body when servicing or repairing the side air curtain module to prevent fatal injuries caused by accidental deployment. Any vehicle with Safety Canopy® or side air curtain modules must display the word air bag on the headliner when it touches each B-pillar trim section or deployment risks will occur. After Safety Canopy® or side air curtain module deployment you need to replace the headliner and new A-, B-, C-pillar upper trim panels and attaching hardware while removing damaged components to stop potential incorrect deployment. Perform inspection of Safety Canopy® or side air curtain module before the installation process begins; if damage is present and module protection is compromised, conduct a replacement immediately. The proper deployment can be hindered by any deployment path obstruction or fasteners used around the module area. A damage check of the roofline needs to occur before any installation process together with necessary restoration work on the original condition. Prior to vehicle release the air bag warning indicator will light up when the correct Restraints Control Module (RCM) fuse is removed in the ON ignition state along with complete Supplemental Restraint System (SRS) operation being necessary. Start by taking out the headliner and de-energize the SRS system while folding the rear seat backrests down and removing pin-type retainers followed by lifting the parcels shelf. To begin disconnect the electrical connector of the side air curtain module and uninstall both the tether bracket front bolt and pin retainers from the A-pillar trim bracket. The processes include separating the side air curtain module bolt from its A-pillar trim bracket where technicians need to use new torque-prevailing type J-nuts for effective fastener attachment. Begin by unscrewing the middle and rear bolts fastening the side air curtain module then remove the two rear bracket bolts before taking out the module by pulling it toward the vehicle front. The installation process finishes by putting back the SRS system power and reinstalling the headliner while performing the opposite steps of removal. The installation requires torque at 14 Nm which corresponds to 124 pound-inches for all bolts.
Driver Inflator Module, Midnight Black
YS4Z-54043B13-ABA
Q: How to remove and replace the side Airbag module safely on Ford Focus?
A:
Safety glasses should always be worn when handling side air bag modules to prevent injuries from potential accidental activation. The connectors on the air bag module need to be avoided because probing could result in a deployment incident with personal injury risk for you. Memory saver devices should never be used because they fail to minimize injury risks. A seat with a seat-mounted side air bag along with a safety belt pretensioner requires you to first depower the supplemental restraint system. There is no SRS fault when the air bag warning lamp illuminates because the RCM fuse has been removed during this test cycle. A complete inspection of the SRS operational readiness and lack of faults must occur before any vehicle return to its customer. The first step entails depowering the system before removing the front seat backrest component. Make note of the wiring harness location since a wrong route could lead to damages from seat movement. Use a tool to disconnect the side air bag module wiring harness from the seat frame through the detaching retaining clip. Pull out the side air bag module after removing its retaining nuts and discard these nuts. A side air bag module always requires left-hand or right-hand orientation depending on the seat choice and wire harnesses should rest against the seat base after installation. Use new self-locking nuts to complete the installation by reverting the uninstallation steps. Finally, repower the system.