How to service and repair the front brake pads on Ford Focus?

The initial step to service front brake pads needs proper DOT 3 brake fluid since alternative fluids will permanently harm your brakes and make them unoperable which creates a danger of harm to vehicle occupants. Always handle brake fluid with carefulness and maintain eye protection with a proper sedative solution afterward. In cases of eye contact, use running water for 15-minute eye flushing followed by medical help for prolonged irritation. The ingestion of this substance requires you to drink water followed by vomiting induction before you seek immediate medical attention. Brake fluid has destructive effects on surface components including paint and plastic. Quickly deal with spills by using water for cleaning. Start by checking the master cylinder reservoir brake fluid level then extract fluid until reaching a half-full mark. The vehicle needs to be hoisted while placed in the neutral mode. Start by detaching the brake hose from the supporting bracket followed by removal of the brake pad retaining clip. The caliper sight hole needs to be avoided when retracting pistons due to possible damage. Keep the brake caliper off the flexible hose because you should wire-brace it for support. Set the caliper in place after removing its two bolts then tighten these bolts to 28 Nm (21 ft.lbs.). Check the two brake pads to determine if they meet the layer specification above the metal backing plates before making replacements for worn-out pads and install new pads only in full axle sets. Displacing brake fluid from the master cylinder becomes possible when the caliper piston moves inside housing. To protect these components use a suitable tool and worn brake pad to push the piston into the bores. Conclude pad replacement by performing the reverse steps of installation.

OEM Ford Focus Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Brake Pads found

View related parts
Ford Focus Brake Pads, Front Part Number: G1FZ-2001-A
$76.02 MSRP: $114.67
You Save: $38.65 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads; Disc Brake Pad Set
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Ford Focus | RS | 4 Cyl 2.3 L GAS
View related parts
Ford Focus Brake Pads, Rear Part Number: CV6Z-2200-A
$72.78 MSRP: $112.00
You Save: $39.22 (36%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Disc Brake Pad Set
- Position: Rear
- Replaces: BRF-1445, AV6Z-2200-A, AV6Z-2200-B, BRF-25
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | Electric, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)
View related parts
Ford Focus Brake Pads, Front Part Number: BV6Z-2001-D
$74.26 MSRP: $112.00
You Save: $37.74 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Disc Brake Pad Set
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Focus | S, SE, SEL, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
View related parts
Ford Focus Brake Pads, Rear Part Number: BV6Z-2200-C
$75.91 MSRP: $114.50
You Save: $38.59 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Disc Brake Pad Set
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | Electric | BATTERY EV (EV/BEV)
View related parts
Ford Focus Brake Pads, Front Part Number: BV6Z-2001-B
$79.78 MSRP: $120.33
You Save: $40.55 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Disc Brake Pad Set
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | Electric | BATTERY EV (EV/BEV)
View related parts
Ford Focus Brake Pads, Rear Part Number: FU2Z-2V200-F
$46.59 MSRP: $66.65
You Save: $20.06 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Replaces: BRF-1525, G1FZ-2200-A, BR-1564, G2MZ-2V200-Z, FU2Z-2V200-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Ford Focus | RS, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Brake Pads, Front Part Number: FU2Z-2V001-G
$46.59 MSRP: $66.65
You Save: $20.06 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: CV6Z-2001-A, FU2Z-2V001-B, BRF-14, G2MZ-2V001-AV, BR-1563
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2014 Ford Focus | Electric, S, SE, SEL, Titanium | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)
View related parts
Ford Focus Brake Pads, Front Part Number: EJ7Z-2001-C
$78.57 MSRP: $118.50
You Save: $39.93 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Disc Brake Pad Set; Front Pads
- Position: Front
- Replaced by: CV6Z-2001-N
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2018 Ford Focus | ST | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Brake Pads, Front Part Number: BV6Z-2001-G
$67.80 MSRP: $104.33
You Save: $36.53 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: BV6Z-2001-C, BRF-34
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2017 Ford Focus | ST | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Brake Pads, Front Part Number: 8U2Z-2V001-B
$44.51 MSRP: $66.65
You Save: $22.14 (34%)
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Pads
- Position: Front
- Replaces: 8U2Z-2V001-A, BR-1339, BRF-1339, 9S4Z-2001-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Focus | S, SE, SEL, SES | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Brake Pads, Front Part Number: 5U2Z-2V001-L
$44.51 MSRP: $66.65
You Save: $22.14 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: 5U2Z-2V001-F, 4S4Z-2001-AA, 5S4Z-2001-AA, BR-1044-B, BRF-1397
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Focus | S, SE, SES, ST, ZX3, ZX4, ZX4 ST, ZX5, ZXW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Brake Pads, Front Part Number: YS4Z-2001-AA
$41.33 MSRP: $56.24
You Save: $14.91 (27%)
ADD TO CART
Product Specifications
- Other Name: Kit - Caliper Brake Pad; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Disc Brake Pad Set
- Manufacturer Note: Less SVT
- Position: Front
- Replaced by: YU2Z-2V001-KA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2004 Ford Focus | LX, SE, Sony Limited Edition, ZTS, ZTW, ZX3, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Brake Pads Part Number: 1S4Z-2200-BA
Product Specifications
- Other Name: Kit - Caliper Brake; Disc Brake Pad Kit; Disc Brake Pad Set; Rear Pads; Kit - Caliper Brake Pad
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2007 Ford Focus | LX, S, SE, SES, Sony Limited Edition, ST, SVT, ZTS, ZTW, ZX3, ZX4, ZX4 ST, ZX5, ZXW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Brake Pads, Front Part Number: 2M5Z-2001-AB
Product Specifications
- Other Name: Kit - Caliper Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Kit - Caliper Brake Pad; Disc Brake Pad Set
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2004 Ford Focus | SVT | 4 Cyl 2.0 L GAS

Ford Focus Brake Pads

OEM Brake Pads boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Pads with long life and a perfect fit. Come to our website and find genuine Ford Focus parts. We keep a wide inventory of OEM Focus parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Brake pads are key components of the braking systems of Ford Focus vehicles - consists of metal components that rub against rotors thereby converting kinetic energy to thermal energy and thus slowing the vehicle. They are characteristically metallic coated and synthetic raw material to be able to work at high temperatures such as up to 400 degrees when in use. Different kinds of brake pads have already been utilized on the Ford Focus models such as non-metallic, semi-metallic, metallic, and ceramic brake pads. All three types incorporate different features with regards to the contact's friction, wear abilities and relative noise. Brake Pad maintenance is very important, the pad has to be changed approximately every 50,000 mile and the wear indicator does its job of letting the driver know when it should be changed. Also it is advisable to make sure that new hardware is installed properly in order to get better efficiency and durability of Ford Focus brake pads.

Ford Focus Brake Pads Parts and Q&A

Brake Pads
1S4Z-2200-BA
Q: How to service and repair the front brake pads on Ford Focus?
A:
The initial step to service front brake pads needs proper DOT 3 brake fluid since alternative fluids will permanently harm your brakes and make them unoperable which creates a danger of harm to vehicle occupants. Always handle brake fluid with carefulness and maintain eye protection with a proper sedative solution afterward. In cases of eye contact, use running water for 15-minute eye flushing followed by medical help for prolonged irritation. The ingestion of this substance requires you to drink water followed by vomiting induction before you seek immediate medical attention. Brake fluid has destructive effects on surface components including paint and plastic. Quickly deal with spills by using water for cleaning. Start by checking the master cylinder reservoir brake fluid level then extract fluid until reaching a half-full mark. The vehicle needs to be hoisted while placed in the neutral mode. Start by detaching the brake hose from the supporting bracket followed by removal of the brake pad retaining clip. The caliper sight hole needs to be avoided when retracting pistons due to possible damage. Keep the brake caliper off the flexible hose because you should wire-brace it for support. Set the caliper in place after removing its two bolts then tighten these bolts to 28 Nm (21 ft.lbs.). Check the two brake pads to determine if they meet the layer specification above the metal backing plates before making replacements for worn-out pads and install new pads only in full axle sets. Displacing brake fluid from the master cylinder becomes possible when the caliper piston moves inside housing. To protect these components use a suitable tool and worn brake pad to push the piston into the bores. Conclude pad replacement by performing the reverse steps of installation.