How to service and repair the parking brake cable on all on Ford Focus?

A technician should start parking brake cable service and repair work by taking out the floor console and activating the parking brake release while working on all vehicles. Adjust the parking brake cable adjustment nut until it reaches thread limit then remove its retaining clip. Position the vehicle in neutral mode before installing it on the hoist while maintaining support for the exhaust pipe. The exhaust tailpipe and muffler assembly must be discarded after nut removal to install fresh assembly nuts with a torques setting of 47 Nm (35 ft. lbs.). Begin the process by disconnecting the hanger isolators followed by removal of the center exhaust hanger isolator then separate the exhaust center and rear heat shields. Remove the parking brake cable from the equalizer then take notes about the outer cable conduit clip positions which will help for reinstalling. You should first detach the parking brake cable from mounting clips then proceed to detach the rear air deflectors if present by unscrewing the clip. Take out the parking brake cable guide bolt from the floor panel together with the cable from its bracket. The sensor bolt for rear wheel speed sensors on vehicles with anti-lock brakes should be removed first and placed aside after installing it with 9 Nm (80 inch lbs.) torque. Vehicle owners should detach all components related to the rear drum brakes starting with the removal of the parking brake cable guide bolt and brake drum followed by lineup of the cable through the lower control arm and backing plate at the cable union. The parking brake cable detachment process requires that you extract the cable from both rear lower control arm calipers and disconnect it from its corresponding levers before taking away the cable conduit retaining clip. The procedure ends with parking brake cable removal followed by black sleeve RH cable and white sleeve LH cable identification before reinstalling by performing the reverse actions while adjusting the parking brake properly.

OEM Ford Focus Parking Brake Cable

Emergency Parking Brake Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Parking Brake Cables found

View related parts
Ford Focus Rear Cable Part Number: CV6Z-2A635-A
$15.51 MSRP: $24.00
You Save: $8.49 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | RS, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Intermediate Cable Part Number: BV6Z-2A603-C
$52.71 MSRP: $86.73
You Save: $34.02 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Replaces: BV6Z-2A603-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | RS, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Intermediate Cable Part Number: AV6Z-2A603-B
$52.05 MSRP: $85.64
You Save: $33.59 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable; Rear Cable
- Manufacturer Note: One Kit Will Service Both Sides
- Replaces: AV6Z-2A603-A, BRCA-58, CV6Z-2A603-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | RS, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Front Cable Part Number: BV6Z-2853-B
$41.11 MSRP: $65.27
You Save: $24.16 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Replaces: CV6Z-2853-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | Electric, S, SE, SEL, ST, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)
View related parts
Ford Focus Front Cable Part Number: 8S4Z-2853-A
$22.32 MSRP: $30.87
You Save: $8.55 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Focus | S, SE, SEL, SES | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Rear Cable Part Number: CV6Z-2A603-E
$54.47 MSRP: $91.27
You Save: $36.80 (41%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: One Kit Will Service Both Sides
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | Electric | BATTERY EV (EV/BEV)
View related parts
Ford Focus Rear Cable Part Number: 2M5Z-2A635-AA
$13.05 MSRP: $17.75
You Save: $4.70 (27%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: RH & LH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Focus | LX, SE, SVT, ZTS, ZTW, ZX3, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Rear Cable Part Number: AS4Z-2A603-B
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Replaces: AS4Z-2A603-A, 9S4Z-2A603-B, 9S4Z-2A603-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Focus | S, SE, SEL, SES | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Rear Cable Part Number: YS4Z-2A635-AA
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: RH or LH, With Rear Drum Brakes
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2003 Ford Focus | LX, SE, Sony Limited Edition, SVT, ZTS, ZTW, ZX3, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Front Cable Part Number: YS4Z-2853-AA
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Manufacturer Note: "Bullet" type cable end
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2007 Ford Focus | LX, S, SE, SES, Sony Limited Edition, ST, SVT, ZTS, ZTW, ZX3, ZX4, ZX4 ST, ZX5, ZXW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Rear Cable Part Number: 3S4Z-2A635-AA
Product Specifications
- Other Name: Cable Assembly - Parking Brake; Brake Cable
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Focus | S, SE, SES, ST, ZX3, ZX4, ZX4 ST, ZX5, ZXW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS

Ford Focus Parking Brake Cable

OEM Parking Brake Cable boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Parking Brake Cable with long life and a perfect fit. Come to our website and find genuine Ford Focus parts. We keep a wide inventory of OEM Focus parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Parking Brake Cable in Ford Focus cars play a very important function of the parking brake system to ensure that the car does not move when it is parked especially on a slope. This is sometimes referred to as the emergency Parking Brake Cable and rolls the parking brake into the overall braking system for the added safety of the car in that it will not be able to roll. Different designs and types of Parking Brake Cable have been used in Ford Focus as the years progressed with these changes mainly focused on the material used in their construction. Consequently, a worn or stretched Parking Brake Cable may not adequately set off the parking brake while a broken cable means that the parking brake does not work at all, which may be dangerous. This paper puts emphasis that Parking Brake Cable of Ford Focus vehicles is required to maintain in a regular manner to support the proper functioning of the parking brake system.

Ford Focus Parking Brake Cable Parts and Q&A

Rear Cable
3S4Z-2A635-AA
Q: How to service and repair the parking brake cable on all on Ford Focus?
A:
A technician should start parking brake cable service and repair work by taking out the floor console and activating the parking brake release while working on all vehicles. Adjust the parking brake cable adjustment nut until it reaches thread limit then remove its retaining clip. Position the vehicle in neutral mode before installing it on the hoist while maintaining support for the Exhaust Pipe. The exhaust tailpipe and Muffler assembly must be discarded after nut removal to install fresh assembly nuts with a torques setting of 47 Nm (35 ft. lbs.). Begin the process by disconnecting the hanger isolators followed by removal of the center exhaust hanger isolator then separate the exhaust center and rear heat shields. Remove the parking brake cable from the equalizer then take notes about the outer cable conduit clip positions which will help for reinstalling. You should first detach the parking brake cable from mounting clips then proceed to detach the rear air deflectors if present by unscrewing the clip. Take out the parking brake cable guide bolt from the floor panel together with the cable from its bracket. The sensor bolt for rear wheel speed sensors on vehicles with anti-lock brakes should be removed first and placed aside after installing it with 9 Nm (80 inch lbs.) torque. Vehicle owners should detach all components related to the rear drum brakes starting with the removal of the parking brake cable guide bolt and brake drum followed by lineup of the cable through the lower Control Arm and backing plate at the cable union. The parking brake cable detachment process requires that you extract the cable from both rear lower control arm calipers and disconnect it from its corresponding levers before taking away the cable conduit retaining clip. The procedure ends with parking brake cable removal followed by black sleeve RH cable and white sleeve LH cable identification before reinstalling by performing the reverse actions while adjusting the parking brake properly.