How to service and repair the front brake pads on Ford Fusion?

The initial step to service and repair the front brake pads requires using accepted DOT 3 brake fluid because it safeguards brake components from permanent damage. You must be aware of the master cylinder reservoir fluid level and drain fluid until reaching half full in order to proceed. Place the vehicle onto a hoist rack in neutral position. Sight hole probing to retract pistons should be avoided because doing so leads to caliper component damage. Allowing the brake caliper to depend from the brake hose will lead to hose damage. Supported by mechanic's wire, remove the caliper guide pin bolts which are part of the two components. The procedure continues with removal of two brake pad retraction springs before extracting the brake pads alongside brake pad shims and stainless steel shims. Check them for any wear or contamination present. Detach the brake pad slides along with their four brake pad slide clips. Installation begins when you put in place the four brake pad slide clips first. Store the caliper piston and boots in a safe position while using the appropriate tool to push the pistons inside the caliper. Apply the provided grease to the pad backing plate and shims according to indications while ensuring measurement of grease for the back of the brake pad and inner piston stainless steel shim and outer stainless steel shim. Place the cut shim on the inside brake pad and direct it to face ahead with confirmation through bottom sideweir of the shim hole. Mount the brake pad shims together with stainless steel shims onto brake pads followed by attaching the two brake pad retraction springs. Position the caliper guide pin boots properly on the anchor plate so contamination does not occur by placing the boot lip beneath the anchor plate extension. Install the brake caliper while keeping the brake caliper hose untwisted before securing the two guide pin bolts to a torque setting of 27 Nm (20 ft. lbs.). Normal brake operation must be tested after filling the brake master cylinder reservoir with clean specified brake fluid.

OEM Ford Fusion Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Brake Pads found

View related parts
Ford Fusion Brake Pads Part Number: HP5Z-2001-C
$103.28 MSRP: $150.33
You Save: $47.05 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Kit; Disc Brake Pad Set; Front Pads
- Replaces: BRF-1544, HP5Z-2001-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Brake Pads, Front Part Number: 6U2Z-2V001-F
$46.59 MSRP: $66.65
You Save: $20.06 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Front Pads
- Position: Front
- Replaces: 6U2Z-2V001-D, BR-1164-B, 9E5Z-2001-A, 6E5Z-2001-C, 6E5Z-2001-B, BRF-1164, 7E5Z-2001-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2012 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Brake Pads, Rear Part Number: 6U2Z-2V200-B
$45.79 MSRP: $66.65
You Save: $20.86 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Rear; Rear Pads
- Manufacturer Note: Ford Retail Spec
- Position: Rear
- Replaces: 6E5Z-2200-C, BE5Z-2200-A, 6E5Z-2200-B, BRF-24, 9E5Z-2200-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2012 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Brake Pads, Rear Part Number: DG9Z-2200-N
$70.83 MSRP: $106.83
You Save: $36.00 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Disc Brake Pad Set
- Position: Rear
- Replaces: BRF-29, DG9Z-2200-A, DG9Z-2200-J, BRF-1498
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Brake Pads, Rear Part Number: DG9Z-2200-F
$78.12 MSRP: $117.83
You Save: $39.71 (34%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Disc Brake Pad Set
- Position: Rear
- Replaces: BRF-1434, DG9Z-2200-D, BRF-1500
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Brake Pads, Front Part Number: DG9Z-2001-M
$66.29 MSRP: $99.98
You Save: $33.69 (34%)
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Disc Brake Pad Set; Front Pads
- Position: Front
- Replaces: BRF-1502, BRF-33, DG9Z-2001-B, BRF-1533, DG9Z-2001-D, DG9Z-2001-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, SEL, SEL Hybrid, Sport, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Brake Pads, Front Part Number: DG9Z-2001-F
$73.70 MSRP: $111.17
You Save: $37.47 (34%)
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Disc Brake Pad Set
- Manufacturer Note: Warranty Eligible
- Position: Front
- Replaces: BRF-31, DG9Z-2001-A, DG9Z-2001-C, BRF-1501
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Brake Pads, Rear Part Number: DG9Z-2200-R
$65.09 MSRP: $99.98
You Save: $34.89 (35%)
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Rear Pads
- Position: Rear
- Replaces: BRF-1492, DG9Z-2200-H, DG9Z-2200-C, BRF-1497, BRF-35, DG9Z-2200-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Energi SE, Energi Titanium, Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Brake Pads, Rear Part Number: DG9Z-2200-MA
$74.84 MSRP: $115.17
You Save: $40.33 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Replaces: BRF-1555, DG9Z-2200-M, BRF-30, BRF-1499, DG9Z-2200-K, DG9Z-2200-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, SEL, SEL Hybrid, Sport, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Brake Pads, Front Part Number: LG9Z-2001-A
$79.28 MSRP: $122.00
You Save: $42.72 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Disc Brake Pad Set; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Rear Pads Part Number: FU2Z-2V200-D
$45.79 MSRP: $66.65
You Save: $20.86 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad - Brake; Brake Pads
- Replaced by: FU2Z-2V200-H
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Brake Pads, Front Part Number: G3GZ-2001-C
$74.26 MSRP: $112.00
You Save: $37.74 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Lining; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Disc Brake Pad Set
- Manufacturer Note: Warranty Eligible
- Position: Front
- Replaces: BRF-1536, G3GZ-2001-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS

Ford Fusion Brake Pads

OEM Brake Pads boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Pads with long life and a perfect fit. Come to our website and find genuine Ford Fusion parts. We keep a wide inventory of OEM Fusion parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Brake Pads are also used in Ford Fusion cars as important parts in its braking structure and these are used to bring the car to a stand still through friction with the brake rotors. These Brake Pads contain friction compounds that are compressed between metal backing plates to serve the purpose of holding up with high temperature thrant during operation. Maintenance is important because the pads need to be replaced due to the wear and tear that they undergo at some point in time, the averages seem to be around 50,000 miles. Anticipated materials incorporated in Brake Pads used in Ford Fusion models include Non-metallic, semi-metallic, fully metallic, and ceramic Brake Pads. All of them differ for example in friction, wear protection, and noise attenuation characteristics. Furthermore, the application of Brake Pads involves other parts which include clips and springs to be change as a measure of enhancing their efficiency and durability. Altogether, the usage and application of Ford Fusion Brake Pads is improved through proper procurement and management therefore helping the vehicle's safety/performances.

Ford Fusion Brake Pads Parts and Q&A

Brake Pads, Front
6U2Z-2V001-F
Q: How to service and repair the front brake pads on Ford Fusion?
A:
The initial step to service and repair the front brake pads requires using accepted DOT 3 brake fluid because it safeguards brake components from permanent damage. You must be aware of the master cylinder reservoir fluid level and drain fluid until reaching half full in order to proceed. Place the vehicle onto a hoist rack in neutral position. Sight hole probing to retract pistons should be avoided because doing so leads to caliper component damage. Allowing the Brake Caliper to depend from the brake hose will lead to hose damage. Supported by mechanic's wire, remove the caliper guide pin bolts which are part of the two components. The procedure continues with removal of two brake pad retraction springs before extracting the brake pads alongside brake pad shims and stainless steel shims. Check them for any wear or contamination present. Detach the brake pad slides along with their four brake pad slide clips. Installation begins when you put in place the four brake pad slide clips first. Store the caliper piston and boots in a safe position while using the appropriate tool to push the pistons inside the caliper. Apply the provided grease to the pad backing plate and shims according to indications while ensuring measurement of grease for the back of the brake pad and inner piston stainless steel shim and outer stainless steel shim. Place the cut shim on the inside brake pad and direct it to face ahead with confirmation through bottom sideweir of the shim hole. Mount the brake pad shims together with stainless steel shims onto brake pads followed by attaching the two brake pad retraction springs. Position the caliper guide pin boots properly on the anchor plate so contamination does not occur by placing the boot lip beneath the anchor plate extension. Install the brake caliper while keeping the brake caliper hose untwisted before securing the two guide pin bolts to a torque setting of 27 Nm (20 ft. lbs.). Normal brake operation must be tested after filling the brake master cylinder reservoir with clean specified brake fluid.